Frigidaire IM115 Support Question
Frigidaire IM115 Support Question
Find answers below for this question about Frigidaire IM115 - Ice Maker Kit.Need a Frigidaire IM115 manual? We have 1 online manual for this item!
Question posted by 2suse on October 3rd, 2013
How To Install Ice Maker Im115
The person who posted this question about this Frigidaire product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Frigidaire IM115 Manual Pages
User Manual - Page 1
... will be responsible for any damage if plastic tubing is used for the supply line. • DO NOT install water supply tubing in a kit from electrical power before connecting a water supply line to install the ice maker kit. • 1/4 inch copper supply line with shut off valve • 1/4 inch brass compression nut and ferrule • Freezer...
User Manual - Page 2
...; ¼ inch Socket Wrench
or Nut Driver • Knife
• Pliers • Needle Nose Pliers • Adjustable Wrench
2 Screws - Use This Page to Identify Parts
1. Ice Maker
2. Qty 1
9. Water Valve - Plastic Clamp - Qty 2
5. Qty 1
7.
User Manual - Page 3
... tight against back of shelf is mounted inside freezer compartment with putty knife.
6. Peel off label covering ice maker hole.
7. DO NOT remove compressor sound baffle (A), if installed.Carefully bend condenser out away from hole.
5. Remove ice tray rack from wall outlet.
2. Rotate while inserting tube until right side of refrigerator.
3 1. Unplug refrigerator from...
User Manual - Page 4
... tight.
10. Mount ice maker onto two screws (5) you installed in one half turn with screw (6). Tighten screw (6) when level.
4 Ice maker is level when gap between freezer wall and ice maker is same at top and bottom. Tighten another one hand, plug ice maker connector into freezer wall. Adjust leveling bracket (7) to level ice maker (1). 9. Start two, long, ice maker mounting screws...
User Manual - Page 5
... holes. Secure plastic water tubing to water valve. DO NOT over tighten.
16. Set ice container (2) on shelf.
18. Make sure connection is tight.
20. On refrigerators with exterior...or alcohol before applying clamps.
17. On models with dynamic condensers, remount sound baffle, if installed. 15. Finger tighten nylon compression nut onto threaded end of rear panel. Holes are only...
User Manual - Page 6
... type shutoff valve.
• A compression nut and ferrule (sleeve) for installing a water supply line. To Connect Water Supply Line To Ice Maker Inlet Valve 1. Slide ferrule (sleeve) into a water softening system.
NOTE: Water line kit number 5303917950, available from the softener may cause ice maker to cycle two or three times before connecting a water supply line...
User Manual - Page 7
... is operating.
• Motor running • Ice loosening from a malfunctioning softener can damage the ice maker. If your dishwasher. • Wash ice container in warm water with mild detergent. The ice maker will hit the ice when the ice container is softened.
The ice maker turns off for short vacations. • If the ice maker will be sure the wire signal arm...
Similar Questions
How Long For Ice Maker Im115 To Make Ice
(Posted by Anabeaye 10 years ago)
How To Manually Cycle Ice Maker Im115
(Posted by moeSeagu 10 years ago)
How To Install Ice Maker Kit Im115
(Posted by mikmDaniel 10 years ago)
Ice Maker Im115
What does the adjustment screw on the front of the ice maker do? it is marked with a -/+ and under t...
What does the adjustment screw on the front of the ice maker do? it is marked with a -/+ and under t...
(Posted by dlbecker7 12 years ago)
Space Dimension Requirements For Frigidaire Complete Ice Maker Kit Im-501?
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
I plan to install an ice maker in a small upright freezer. I need the dimension requirements for th...
(Posted by dan1b 12 years ago)