Dell PowerConnect 6248 Support Question
Dell PowerConnect 6248 Support Question
Find answers below for this question about Dell PowerConnect 6248.Need a Dell PowerConnect 6248 manual? We have 5 online manuals for this item!
Question posted by netrenaer on September 14th, 2013
How Do I Restart A Powerconnect 6248 Remotely
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerConnect 6248 Manual Pages
Command Line Interface Guide - Page 1327
"ColdAuto-Restart" means that the system switched from the active manager to the backup manager and was unable to start the last ...on the management unit. "Power-On" Move means that the primary management card restarted due to take over.
AdministrativeThere are four options. "Warm-AutoRestart" means that the switch rebooted. For the backup manager, the value is set to 0d 00:00:00...
User's Guide - Page 19
Release notes are standalone Layer 2 and 3 switches that extend the Dell PowerConnect LAN switching product range. The Dell PowerConnect 6248 supports 48 1000Base-T copper ports and 4 "combo" ports for RJ-45 or SFP interfaces. The Dell PowerConnect 6224 switch supports 24 1000Base-T copper ports and 4 "combo" ports for RJ-45 or SFP interfaces. For a list of service, security...
User's Guide - Page 21
... the user to be captured across the entire network. Trivial File Transfer Protocol (TFTP) The PowerConnect 6200 Series switches support boot image, firmware, and configuration upload or download through TFTP. For information about SNTP, see "Managing Logs."
Remote Monitoring (RMON) RMON is composed of backup firmware images. Syslog Syslog is fully manageable using...
User's Guide - Page 56
.../1000M Base-T Auto-sensing Full-Duplex RJ-45 Ports
56
Hardware Description
Combo Ports Figure 4-2. PowerConnect 6248 with 24 10/100/1000 Base-T Ports
10/100/1000Base-T Auto-sensing Full Duplex RJ-45 Ports
Combo Ports
The PowerConnect 6248 front panel provides 48 10/100/1000M Base-T RJ-45 ports and four RJ-45...
User's Guide - Page 59
..., 6248, and 6224F Rear Panel
Dual 10G slots for XFP, CX4, or stacking modules
Dual 10G slots for XFP, CX4, or 10Gbase-T modules.
RS-232 management port
DC power
AC power
Hardware Description
59 Figure 4-6. RS-232 management port
DC power
AC power
Figure 4-7. Rear Panel
Each PowerConnect 6200 series switch provides an...
User's Guide - Page 62
... the LEDs. See "System LEDs" for information on the switch to connect the switches. The PowerConnect 6248 has four fans. Connect one internal power supply which requires standard AC.
Stacking
You can also attach a redundant DC power supply, such as the PowerConnect RPS-600. For each switch in the stack.
2. Use the remaining stacking cable to...
User's Guide - Page 549
...) for example, to be redistributed by the operator (see "Nonstop Forwarding" on page 258).
When OSPF graceful restart is displayed.
• Subnets - In helper mode, a switch continues to advertise to be redistributed. • Metric -
Graceful restart can continue to be configured to forward packets through this protocol to address a partial hardware
Configuring Routing...
User's Guide - Page 669
... change and and the potential for example, to address a partial hardware failure), to forward packets using OSPFv3 routes while a backup switch takes over management unit responsibility. Configuring IPv6
669 Graceful restart can continue to correct faulty system behavior which determine OSPFv3 routes).
The operator may initiate a failover in a stack fails, the hardware...
Getting Started Guide - Page 266
... counters show stack-port diag show switch
show supported switchtype
LED
LED Dell Power Connect PC6248P ,PC6224P ,PC6248 , PC6224ו.PC6224F -
PowerConnect 6200
PC 6224
1-1
PC 6248
2-1
...
Release Notes - Page 3
... in the zip file to installing or upgrading of firmware be thoroughly reviewed prior to update the boot code AND firmware. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Introduction
This document provides specific information for the Dell PowerConnect 6200 Series switches, firmware version 3.2.0.6.
You MUST follow the procedure set forth in the Dell...
Release Notes - Page 4
... to deploy firmware, do not use the method described in these Release Notes to a backup location before performing this firmware.
Hardware Supported
PowerConnect 6224 PowerConnect 6248 PowerConnect 6224F PowerConnect 6224P PowerConnect 6248P
2
System Firmware Version 3.2.0.6
Supported Firmware Functionality
For more details regarding the functionalities listed, please refer to...
Release Notes - Page 5
...a VLAN name as an alternative to forward packets while the control and management planes restart as protocols for protocol-based VLANs.
This feature is configurable via the CLI or ... of the switch will allow the forwarding plane of stack units to continue to a number when RADIUS indicates the Tunnel-Private-Group-ID for a supplicant. PowerConnect 6224/6224F/6224P/6248/6248P Release ...
Release Notes - Page 7
...feature prevents a class of man-in a VLAN). PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ MLD Snooping (RFC2710)
In IPv4, Layer 2 switches can use IGMP Snooping to limit the flooding of... is used to share information between neighboring devices (routers, bridges, access servers, and switches). This list is constructed by default if using phones with Cisco™ devices running ...
Release Notes - Page 15
.... If your previous configuration had flow control disabled, you upgrade a switch to 20-600 centiseconds.
¾ IP Multicast Static Route Configuration
The command for configuring all trap flags. The ip multicast staticroute command is enabled by default.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ Trap Configuration
In previous versions of the...
Release Notes - Page 19
...not be deleted for logging syslog.
Re-enabled objects to remove switch x priority x. Make the Web field names similar to accept ...switch 2 priority 2 command does not work. The user cannot determine how cutthrough mode is configured via the show UTC time instead of issues resolved in the respective APIs. Configured non-existing host cannot be deleted.
PowerConnect 6224/6224F/6224P/6248...
Release Notes - Page 23
.... Since the IETF implementation is the only one supported, this command to disable graceful restart. • ietf - Default: A helpful neighbor exits helper mode upon a topology change occurs. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
CLI Reference Manual Updates
Non-Stop Forwarding
Title nsf no nsf show nsf show checkpoint statistics clear checkpoint...
Release Notes - Page 25
.... The user would have to type "y" or "n" to continue to delete the message, and disable the banner.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
RADIUS Accounting Servers
Title radius-server host acct
Description The switches do not support creating accounting server names with the same name although the CLI Reference Manual and...
Release Notes - Page 27
...Firmware Version 3.2.0.6
Page 25 VLAN configuration is applied correctly. User Impact When the switch reboots and attempts to save configuration changes even though no reason for file download ...to avoid the restarting order. Increase the dead internal timer. TACACS operation
Ping fails with 33% to startup-config through HTTP.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes...
Release Notes - Page 29
...Page 27 Workaround The administrator can work around this problem by shutting down the port and restarting it after getting the VLAN assigned, DUT stops advertising Voice VLAN reply TLV in its ...used as login method and enable authentication is none, the user is changed .
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Summary
ISDP updates are not including Voice VLAN Reply TLV when ...
Release Notes - Page 31
...for VLAN routing interfaces. User Impact The maximum number of the PowerConnect 6200 series switches. DiffServ
Description Failed to attach diffserv policy to become active with...known limitation of MAC-based VLANs is for the interface being configured.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
LACP
Description LAGs Supported
VLAN
Description vlan association mac command...
Similar Questions
How To Save Config On Dell Powerconnect 6248 Browser
(Posted by bisbesuepat 9 years ago)
How To Document Dell Powerconnect 6248 Configuration
(Posted by wertscu 9 years ago)
Powerconnect 6248 Stacking Module Is It Hot Swappable
PowerConnect 6248 stacking module is it hot swappable? I am trying to add a switch to an existing 6...
PowerConnect 6248 stacking module is it hot swappable? I am trying to add a switch to an existing 6...
(Posted by richardcadogan 11 years ago)