Dell PowerConnect 6248 Support Question
Dell PowerConnect 6248 Support Question
Find answers below for this question about Dell PowerConnect 6248.Need a Dell PowerConnect 6248 manual? We have 5 online manuals for this item!
Question posted by jgb2smi on December 16th, 2013
Powerconnect 6248 How To Find Ipaddress Cli
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by MWatDell on December 17th, 2013 4:38 AM
MWatDell
Member since:
November 17th, 2011 Points: 306,490
Member since:
November 17th, 2011 Points: 306,490
Hi jgb2smi
Not sure which specific ipaddress cli that you are looking for but here's the cli reference guide for PowerConnect 6248:-
ftp://ftp.dell.com/Manuals/all-products/esuprt_ser_stor_net/esuprt_powerconnect/powerconnect-6248_Reference%20Guide_en-us.pdf
Hope this help.
MW@Dell
Related Dell PowerConnect 6248 Manual Pages
User's Guide - Page 19
... topics covered in this product. 1
Introduction
This section describes the switch user-configurable features. The Dell PowerConnect 6224P adds support for PoE capability. The Dell PowerConnect 6224F switch supports 24 1000Base-FX SFP ports and 4 "combo" ports for RJ-45 or SFP interfaces. The Dell PowerConnect 6248 supports 48 1000Base-T copper ports and 4 "combo" ports for...
User's Guide - Page 45
... stack. Defining Fields
User-defined fields can be used to access the device is similar to the Master switch of log files, select match criteria for the following
Accessing the Switch Through the CLI
The switch can contain 1-159 characters, unless otherwise noted on a Linux system.
If access is attached to entering commands on...
User's Guide - Page 56
.../100/1000M Base-T Auto-sensing Full-Duplex RJ-45 Ports
56
Hardware Description
Combo Ports PowerConnect 6248 with 24 10/100/1000 Base-T Ports
10/100/1000Base-T Auto-sensing Full Duplex RJ-45 Ports
Combo Ports
The PowerConnect 6248 front panel provides 48 10/100/1000M Base-T RJ-45 ports and four RJ-45...
User's Guide - Page 59
... an RS-232 maintenance port, on the rear of the switch.
PowerConnect 6224, 6248, and 6224F Rear Panel
Dual 10G slots for XFP, CX4, or stacking modules
Dual 10G slots for XFP, CX4, or 10Gbase-T modules. RS-232 management ...
User's Guide - Page 62
... cable to stacking port two on the top and bottom switches.
62
Hardware Description For PoE switches, you can verify operation by observing the LEDs. The PowerConnect 6248 has four fans. Install a separately purchased stacking module in the stack.
2. Power Supplies
The 6200 series switches have one of the short stacking cables into either of...
Getting Started Guide - Page 266
... counters show stack-port diag show switch
show supported switchtype
LED
LED Dell Power Connect PC6248P ,PC6224P ,PC6248 , PC6224ו.PC6224F -
PowerConnect 6200
PC 6224
1-1
PC 6248
2-1
...
Release Notes - Page 4
...OMNM 4.1 will not discover the switches running firmware version 2.x or earlier.
Only use it to deploy 3.x (or later) firmware to a PowerConnect 62xx device that is not supported.
Firmware Downgrade
Downgrading from 3.2.0.6 to the Dell™ PowerConnect™ 6200 Series Systems CLI Reference Guide and the Dell™ PowerConnect™ 6200 Series Configuration Guide. Firmware...
Release Notes - Page 5
...changing the role of a module, a reboot of the switch will be unique.
¾ HTTP Download
Allow users to download files via the CLI or GUI and supports 1500 characters.
¾ VLAN Name... as protocols for a single command that displays on the stack management unit.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Added Functionality in this Release ¾ Non-Stop Forwarding
This...
Release Notes - Page 7
...DSCP parameter and set the DSCP value. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ MLD Snooping (RFC2710)
In IPv4, Layer 2 switches can use IGMP Snooping to limit the ... is used to share information between neighboring devices (routers, bridges, access servers, and switches).
The miscreant sends ARP requests or responses mapping another station's IP address to all its...
Release Notes - Page 9
...on a router with unwanted destination addresses.
¾ Clear ARP Cache Management Port
A new CLI command has been added to enable clearing of the ARP table of entries learned from the management...route into another area can lead to routing loops in the link state topology. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ Ping/Traceroute Enhancements
New ping options have been added ...
Release Notes - Page 11
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ Configured Tunnels MTU
To comply with RFC 4213, Basic ...
This adds configuration options for carrying IPv6 traffic. The ip helper-address commands configure both DHCP and UDP relay.
¾ OSPF Enhancements
A CLI command is support for a 6 to 4 border router that includes other 6 to 4 border routers and 6 to 4 relay routers.
&#...
Release Notes - Page 13
...agents that port as the blocking state). System Firmware Version 3.2.0.6
Page 11 PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Changed Functionality in this state until it receives a BPDU ...tree states include blocking, listening, learning, and forwarding. Loop Guard - The reasons for all CLI. When a port is not forwarded (acting in designated roles should be modified; In the ...
Release Notes - Page 15
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
¾ Trap Configuration
In previous versions of the software, configuration of the...all trap flags. snmp-server enable traps is automatically enabled. If your previous configuration had flow control disabled, you upgrade a switch to 128. Also note that the keyword "trap" has changed to the plural "traps".
¾ SNTP Server Priority
The...
Release Notes - Page 17
... mode
Rationale: The mdix { auto | on ports. It has been replaced by the no spanning-tree bpdu flooding command. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Deprecated Commands and Parameters The following CLI commands have been deprecated: • forward • discard-shutdown
Global Configuration mode
Rationale: The logging buffered size command has...
Release Notes - Page 19
... not walk all objects in connected_unit/connected_stby state. PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Issues Resolved
The following is a list of issues resolved in CLI to accept control characters: 'a-z' | 'A-Z' | ...be deleted. Added a new MLD rule to the FFP which will trap to remove switch x priority x. Re-enabled objects to the running -config command. Added a comment to...
Release Notes - Page 21
... Portal user can be present.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Description Cannot enter Daylight Saving Time from Web interface.
Custom Protocol VLAN shows incorrect VLAN ID. System Firmware Version 3.2.0.6
Page 19 On the interface ethernet CLI command, switch gives error message when entering interface names in CLI help . Adding VLAN range issues...
Release Notes - Page 23
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
CLI Reference Manual Updates
Non-Stop Forwarding
Title nsf no nsf show nsf show checkpoint statistics clear checkpoint statistics vlan routing vlanid [index] nsf [ ietf ] [ planned-...
Release Notes - Page 25
... in the quiet state for details.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
RADIUS Accounting Servers
Title radius-server host acct
Description The switches do not support creating accounting server names with the same name although the CLI Reference Manual and User Guide state that the switch waits before authorizing the client if the...
Release Notes - Page 27
...Firmware Version 3.2.0.6
Page 25 Issue with large configuration. CLI command stackport config rejection does not display the cause....capable. Increase the dead internal timer.
None.
PowerConnect 6224/6224F/6224P/6248/6248P Release Notes
Known Issues
Summary Non-configuration... number. If the configuration is saved and the switch is reset, the configuration is possible that all user...
Configuration Guide - Page 9
... settings, use system interfaces and utilities, and create and use the Dell™PowerConnect™ 6200 Series switch in a mixed IPv6/IPv4 network.
• "Quality of Service" on page...servers.
• "IPv6" on page 135 describes configuring and using the command line interface (CLI). 1
About this Document
9
About this Document
This configuration guide provides examples of how to...
Similar Questions
How To Save Config On Dell Powerconnect 6248 Browser
(Posted by bisbesuepat 9 years ago)
How To Firmware Update Dell Powerconnect 6248 From Cli
(Posted by danidedsp 10 years ago)
Powerconnect 6248 Stacking Module Is It Hot Swappable
PowerConnect 6248 stacking module is it hot swappable? I am trying to add a switch to an existing 6...
PowerConnect 6248 stacking module is it hot swappable? I am trying to add a switch to an existing 6...
(Posted by richardcadogan 11 years ago)