Dell PowerConnect 5548 Support Question
Dell PowerConnect 5548 Support Question
Find answers below for this question about Dell PowerConnect 5548.Need a Dell PowerConnect 5548 manual? We have 1 online manual for this item!
Question posted by maliCla on March 30th, 2014
How Do I Create A Mac-based Vlan Using Cli Commands On My Dell 5548 Managed
switch
Current Answers
Related Dell PowerConnect 5548 Manual Pages
User Guide - Page 20
... IP traffic is enabled, the device registers and propagates VLAN membership on all ports that comprise a single Broadcast domain. VLAN Supported Features
VLAN Support
VLANs are classified as belonging to a VLAN, based on either the VLAN tag or on a combination of the ingress port and packet contents. For more information, see "Defining VLAN Membership Using CLI Commands" on page 466.
User Guide - Page 100
... table summarizes the CLI commands for configuring MAC-based ACLs.
MAC Based ACL CLI Commands
CLI Command
Description
mac access-list extended acl- mode. show access-lists Extended IP access list ACL1 permit 234 172.30.40.1 0.0.0.0 any permit 234 172.30.8.8 0.0.0.0 any
100
Dell PowerConnect 55xx Systems User Guide
Configuring MAC-Based ACLs Using CLI Commands The following is...
User Guide - Page 103
...|decspanning|decnetiv|diagnostic|dsm|etype-6000] [vlan vlan-id] [cos cos coswildcard] [time-range timerange-name]
deny {any|source sourcewildcard} {any
Dell PowerConnect 55xx Systems User Guide
103 Configuring MAC-Based ACEs Using CLI Commands The following is an example of some of the CLI commands: console(config)# mac access-list extended server1 console(config-mac-al)# permit 00:00:00:00:00...
User Guide - Page 105
...acl- Figure 8-5. IPv4 Based ACE: Summary
Dell PowerConnect 55xx Systems User Guide
105 Configuring IP-based ACLs Using CLI Commands The following is an example of some of this command to display the IPv4 Based ACE page.
The following table summarizes the CLI commands for configuring IP-based ACLs. Table 8-4. IP-Based ACL CLI Commands
CLI Command
Description
ip access-list...
User Guide - Page 110
...port/port-range } [dscp number|precedence number] [matchall time-range-name] [time-range timerange-name]
110
Dell PowerConnect 55xx Systems User Guide Table 8-5. destination-wildcard} [any |destination-ip-address
found above. type][any|icmp-code... protocols is
wildcard} {any |icmp- Configuring IP-based ACEs Using CLI Commands The following table summarizes the CLI commands for configuring IP...
User Guide - Page 113
... an IPv6-based ACL: 1 Click Switching > Network Security > IPv6 Based ACE to
remove the access list. The following table summarizes the CLI commands for configuring IPv6-based ACLs. configuration mode
list-name]
Use the no ipv6 access-list [access- Figure 8-7.
IPv6 Based ACE: Summary
Dell PowerConnect 55xx Systems User Guide
113 Table 8-6.
IP-Based ACL CLI Commands
CLI Command...
User Guide - Page 116
...IP-Based ACE CLI Commands
CLI Command
Description
permit protocol {any|{source-prefix/length }{any |destination-port/port-range} [dscp number|precedence number] [time-range time-range-name]
116
Dell PowerConnect 55xx... for configuring IP-based ACLs. Configuring IP-based ACEs Using CLI Commands The following table summarizes the CLI commands for IPv6 access list. - Shutdown -
User Guide - Page 119
...(config-mac-al)# exit console(config)# interface gi1/0/1 console(config-if)# service-acl input server
Dell PowerConnect 55xx Systems User Guide
119
Displays access control lists (ACLs) configured on the switch.
Table 8-8. The following table summarizes the CLI commands for configuring ACL Bindings.
. You can select one IPv6-based ACL. ACL Bindings CLI Commands
CLI Command service...
User Guide - Page 129
... and dynamically assign
a VLAN to the device. • The assigned VLAN must not be configured to use both a DVA and a MAC-based
VLAN group. • A RADIUS server must have been
created on behalf of the non-Dot1x-capable devices, and uses the MAC address of the VLAN that are : • Dot1x - The switch can be the default VLAN and must support DVA...
User Guide - Page 133
... field. Permit the session. - Enter the ID of a Guest VLAN for use of the VLAN to which traffic being monitored is removed from the VLAN list. - If no response is permitted.
• RADIUS - Enabling Port-Based Authentication Globally Using the CLI Commands The following table summarizes the CLI commands for example, if the server is down), then no aaa authentication...
User Guide - Page 134
...command to return to disable access. Port-Based Authentication Global CLI Commands (Continued)
CLI Command
Description
dot1x system-auth-control monitor [vlan vlan-id]
no dot1x guest-vlan
Contains a list of this command to default. Use the no form of VLANs.
Use the no format of the CLI commands... n/a
134
Dell PowerConnect 55xx Systems User Guide dot1x guest-vlan no dot1x system...
User Guide - Page 138
... Using the CLI Commands The following table summarizes the CLI commands for enabling the port based authentication as displayed in seconds.
- no dot1x radius-attributes vlan
Use the no dot1x guest-vlan enable
Enables unauthorized users on the interface access to the supplicant. dot1x guest-vlan enable no form of this command to restore the default configuration.
138
Dell PowerConnect...
User Guide - Page 140
...
-------Bob John Clark
n/a
140
Dell PowerConnect 55xx Systems User Guide Enables using a guest VLAN for the device. Use the no form of the CLI commands: console(config)# aaa authentication dot1x default none console(config)# interface vlan 5 console(config-if)# dot1x auth-not-req console(config)# vlan database console(config-vlan)# vlan 2 console(config-vlan)# exit console(config)# interface...
User Guide - Page 213
... mode.
console(config-if)# switchport access Make port a member of
vlan 100
VLAN 100. Configuring Two IP Networks on Two Different VLANS Using CLI The following shows how to configure two IP networks on unit 1. console(config-vlan)# vlan 100-150
Create VLANs number 100 to verify the configuration
Dell PowerConnect 55xx Systems User Guide
213 console(config-if)# switchport access...
User Guide - Page 489
... the primary VLAN and the secondary VLANs. Port is isolated. -
Table 14-6. Use the no form of this command to return the VLAN to associate the isolated VLAN with the isolated VLAN.
4 To assign ports to the private VLAN, click Membership. 5 Select a Primary VLAN ID. 6 Select a Isolated VLAN ID. 7 Select the ports to be assigned to remove the association. Dell PowerConnect 55xx...
User Guide - Page 558
... ip ip-address mac-address mac-address
Creates a static ARP binding. Adding Entries to a Dynamic ARP Inspection List Using CLI Commands The following is an example of some of this command to VLANs:
IP
MAC
172.16.1.1
00:60:70:4c:73:21
172.16.1.2
00:60:70:4c:73:22
console(config-arp-list)#
558
Dell PowerConnect 55xx Systems User...
User Guide - Page 560
...-4. The following table summarizes the CLI commands for configuring the fields in the VLAN Settings pages.
Enables ARP inspection on a VLAN, based
id
on a VLAN. Assigning IP/MAC Address Pairs to VLANs Using CLI Commands The following is an example of some of the CLI commands: console(config)# ip arp inspection list assign 37 servers
560
Dell PowerConnect 55xx Systems User Guide no...
User Guide - Page 567
... untrusted interfaces, whose source MAC address and the DHCP client MAC address do not match. - Save Binding Database Internal (600-86400) - Configuring DHCP Snooping Global Parameters Using CLI Commands
Dell PowerConnect 55xx Systems User Guide
567 Option 82 Passthrough - Global Parameters
2 Enable/disable DHCP snooping on the device: 1 Click Switching > DHCP Snooping > Global Parameters...
User Guide - Page 571
...Table 19-3. The following table summarizes the CLI commands for configuring DHCP snooping on VLANs CLI Commands
CLI Command ip dhcp snooping vlan vlan-id no form of the CLI commands: console(config)# ip dhcp snooping vlan 1
Dell PowerConnect 55xx Systems User Guide
571
DHCP Snooping on VLANs . Configuring DHCP Snooping on VLANs Using CLI Commands
The following is an example of some...
User Guide - Page 674
... possible options are first matched to delete a class map.
674
Dell PowerConnect 55xx Systems User Guide
Defining Class Mapping Using CLI Commands The following table summarizes the CLI commands for setting the fields in the class map. • IP and MAC - Use the no form of the IP-based ACLs in order to belong to detach a class map from the...
Similar Questions
How To Apply An Acl To A Vlan Interface On Dell 5548 Switch
(Posted by bibgs 9 years ago)
How To Set Management Password On Powerconnect 5548
(Posted by loprw273 10 years ago)
Cli Command What Modules Are Installed In Dell 6224
(Posted by thamassim 10 years ago)
How Do I Create A Private Vlan Dell Powerconnect 5548
(Posted by tjinay 10 years ago)