Home » D-Link » Wireless » D-Link DAP-2590

D-Link DAP-2590 Support Question

Find answers below for this question about D-Link DAP-2590 - AirPremier N Dual Band PoE Access Point.
Need a D-Link DAP-2590 manual? We have 1 online manual for this item!

D-Link Overview Questions Manuals Reviews Videos Research

Question posted by diversitysystems on May 3rd, 2015

Dap-2590 Will Not Stay Online And Locks Up.

I have a pair of DAP-2590s that I am trying to operate in the "bridged AP" mode to extend a WiFi network. The wired unit is setup as a Master and the unwired unit is setup as a Slave. Neither unit will stay in operation for over a few days and then they lockup and quit transmitting (and the LEDS quit blinking and remain lit continuously). As soon as I recycle the power they reboot and come right back up operating correctly. But after a few days either one or both will lockup again. I can't figure out why.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by techyagent on May 4th, 2015 11:00 AM

This answer was accepted by the poster of the original question.

techyagent

Member since:
June 17th, 2014

Points: 4,799,820

1,100
points

I think the radio unit of this product is damaged or malfunctioned you have to found a good technician or take it to the dline official repair facility.

They will take good care of it.

or the problem might solved with a firmware upgrade.

Thanks

Techygirl

Related D-Link DAP-2590 Manual Pages

Product Manual - Page 2

... 5 Features and Benefits 6 Wireless Basics 7 Four Operational Modes 10 Getting Started 11 Using the Configuration Menu 13 Home > Basic Settings > Wireless 15 Access Point mode 15 WDS with AP mode 17 WDS mode 19 Wireless Client mode 21 Open System or Shared Key...Administrator Settings 58 Limit Administrator 59 System Name Settings 60 Login Settings 61 D-Link DAP-2590 User Manual

Product Manual - Page 4

... above . System Requirements • Computers with Windows®, Macintosh®, or Linux-based operating systems with the DAP-2590 will cause damage and void the warranty for this product. Product Overview PPraocdkuacgteOCvoenrtevnietsw • D-Link DAP-2590 AirPremier N Dual Band PoE Access Point • Power Adapter • Manual on CD • Ethernet Cable • ��...

Product Manual - Page 5

...Point The AirPremier N Dual Band PoE Access Point allows network administrators to ensure maximum performance. Additionally, the DAP-2590 supports load balance features to deploy a highly manageable and extremely robust dual band wireless network. To further protect your wireless network, MAC Address Filtering, Wireless LAN segmentation, Disable SSID Broadcast, Rogue AP Detection, and Wireless...

Product Manual - Page 6

... v.3 for your data and communications than its previous versions. • AP Manager II management software - The DAP-2590 isn't supported in the 5.25~5.35 GHz and 5.47 ~ 5.725 GHz frequency ranges in one of four different operation modes to meet your wireless networking needs: Access Point, WDS with AP, WDS, or Wireless Client. • ��F�a��s�te...

Product Manual - Page 7

... on the number of implementation. The DAP-2590 saves money by extending the network beyond the home or office. Enjoy the freedom that is not only increasing in both home and office environments, but in any location within your home, business or public access wireless networks. Configurations can operate in four different modes. Wireless adapter cards used on real-time...

Product Manual - Page 8

Installation Standards-Based Technology The DAP-2590 Wireless Access Point utilizes the 802.11a, 802.11b, 802.11g, and 802.11n (draft) standards. within the specified range of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. you will adversely affect wireless signal range. D-Link DAP-2590 User Manual OFDM works by ...

Product Manual - Page 10

Section 2 - Installation Four Operational Modes Access Point (AP) WDS with AP WDS Wireless Client Create a wireless LAN Wirelessly connect multiple networks while still functioning as a wireless AP Wirelessly connect multiple networks AP acts as a wireless network adapter for your Ethernet enabled device D-Link DAP-2590 User Manual 10

Product Manual - Page 15

... to Disable, and then use the pull-down menu. The channel selection process only occurs when the AP is the name designated for a specific wireless local area network (WLAN). Configuration Home > Basic Settings > Wireless Access Point mode In Access Point mode, the DAP-2590 functions as a wireless AP. Wireless Band: Select either 2.4 GHz or 5 GHz from the pull-down menu to establish a new...

Product Manual - Page 17

... AP mode In WDS with AP mode is the name designated (SSID): for a specific wireless local area network (WLAN). The SSID's factory default setting is booting up. Wireless Band: Select either 2.4 GHz or 5 GHz from the pull-down menu. Enabling this feature automatically selects Selection: the channel that will automatically scan and match the wireless settings.) D-Link DAP-2590...

Product Manual - Page 28

...) is expected. If there are packets sent by an access point to save the power of wireless clients, while setting a lower one can be supported include...GHz). The AP will vary. Specify a value in the 5 GHz band. Network conditions and environmental factors, including volume of the DAP-2590. Actual data throughput will adjust the base transfer rate depending on the wireless LAN. ...

Product Manual - Page 29

...and reports sent between two access points where interference is a major concern. WMM (Wi-Fi WMM stands for load balancing. Internet Group Management Protocol allows the AP to select 100%, 50%,...that has been specified, the DAP-2590 will forward multicast packets to share the wireless network traffic and the client using multiple APs. For example, if wireless coverage is the default setting...

Product Manual - Page 30

...access (zero to associate with the AP if the utilization exceeds the value the user specifies. Network Utilization: Set the maximum utilization of 10 is recommended. The default setting is reached, the device will not allow network... of this access point for service. The DAP-2590 will pause one minute to allow any new clients to 64 users).To use this network utilization threshold is...

Product Manual - Page 46

... to let the changes take effect. Information: D-Link DAP-2590 User Manual 46 Once a user is entered, it from this list. Access Control List: Select Disable to accept only those devices with MAC addresses on the Access Control List. Configuration Filters > Wireless MAC ACL The DAP-2590 features a wireless MAC Access Control List filter. Select Accept to disable the...

Product Manual - Page 47

..., which allows stations to intercommunicate by connecting to the Ethernet. Section 3 - Wireless Band: Displays the current wireless band rate. D-Link DAP-2590 User Manual 47 If the Ethernet connection between the LAN and the AP is Enable. In Guest mode, wireless stations cannot exchange data with the AP to be blocked. Ethernet to let the changes take effect. When disabled...

Product Manual - Page 63

.... Public Enter the public SNMP community string. Community String: Private Enter the private SNMP community string. D-Link DAP-2590 User Manual 63 Section 3 - Password: Each of the SNMP manager to receive traps sent from the wireless access point. This is the IP address of the six main categories display various hidden administrator parameters and settings...

Product Manual - Page 71

... Simple WLAN Management Tool When one needs to set up to maintain the wireless network. All AirPremier 11n Business APs support this tool, which can manage up a wireless local area network (WLAN) in a small office, solutions provided for multiple APs an effortless process. Multiple access points (APs) will make WLAN deployment easier and more effort in a small office environment is...

Product Manual - Page 73

... want to check the status of the Slave APs. Section 4 - Using the AP Array Situations Encountered with the longest run-time will become Backup Master APs. • Manually Configured Slave AP: At intervals of one minute, the Master AP will work as stand-alone APs until a new Master joins the array. D-Link DAP-2590 User Manual 73 Note: The other Master APs will become the Master AP.

Product Manual - Page 78

Please see item 3 of the DAP-2590 Wireless Access Point. Any computers that can occur during the installation and operation of this Troubleshooting section to configure the DAP-2590. 1. Go to the DAP-2590. If the LED is not ON, check if the cable for the network adapters are having any technical difficulties. They must have changed the default IP address, make...

Product Manual - Page 79

... Infrastructure mode. The Connect to the wireless adapter. The wireless client cannot access the Internet within the same IP address range as shown in the taskbar, then select the Support tab and the IP address will not need to the wireless adapter is necessary to assign a Static IP Address to Wireless Network screen will appear. D-Link DAP-2590 User...

Product Manual - Page 80

... your product away - D-Link products let you access your network from the wall or other objects. • If you are indicating normal activity. Turn the DAP-2590 back on again, and then turn on the AP and the wireless client are correctly entered for the DAP-2590. Try changing the channel on your DAP-2590, and on all security settings. •...