Craftsman 21419 Support Question
Craftsman 21419 Support Question
Find answers below for this question about Craftsman 21419 - 9 in. Band Saw.Need a Craftsman 21419 manual? We have 1 online manual for this item!
Question posted by glorioussuhn37 on July 16th, 2012
Manual For My Craftsman 9' Band Saw
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.The associates said I need to down load online, but I'm trying to do it but i can't find it.Please help thak you,
Current Answers
Related Craftsman 21419 Manual Pages
Operation Manual - Page 1
Sears, Roebuck and Co., Hoffman
www.sears.comlcraftsman
25126,03 Draft (01/18/08)
Estates,
IL 60179 U.S.A.
perator's
nual
®
tP
BENCH TOP BAND SAW
Model No.
351.214190
CAUTION: Read and follow
all Safety Rules and Operating instructions before First Use of this Product.
Operation Manual - Page 2
...out of power tools.
Remember that may affect a tool's operation. Consult manual for tool. Do not perform makeshift repairs. (Use parts list provided to rain. Never operate power tools
when tired, ... 2-3
3 3 3-4 4-8 8 9 10-13 14-23
ONE-YEAR FULL WARRANTY ON CRAFTSMAN PROFESSIONAL TOOL If this Craftsman tool fails due to a defect in material or
workmanship within one year from the date of...
Operation Manual - Page 3
... power off pieces until it through your tool. Use of improper accessories increases the risk of band saw should be adjusted before assembling: A Miter Gauge Assembly B Table Assembly C Locking Handle with Washer D Table Locking Insert Assembly
may deteriorate these finishes. Check for shipping damage. Use operator's manual to dealer. Secure table in the work...
Operation Manual - Page 4
... loads will cause some drop in voltage and loss of power.
® Wires of the extension cord must be no less than 10% above or below the specified voltage. This tool ...convenient quick tensioning and comprehensive tracking mechanism makes blade changing quick and easy. The Craftsman 9" Bench Top Band Saw features welded steel frame construction and a solid cast iron table surface to 2-prong...
Operation Manual - Page 5
... turned on frame.
5
Wear leather gloves when handling band saw can be turned off but cannot be turned on again.
+ To replace key, slide key into the slot on the left front of the tool and open upper and lower doors. Never wear gloves when operating saw. + Turn blade tension lever on the side...
Operation Manual - Page 6
...contact with another blade. Do not perform tracking adjustment while band saw from blade. Proper tracking is running.
• Disconnect band saw is achieved when drive and idler wheels are aligned. When...and tracked. • Blade guides support blade at sides and rear of the tool frame is a spring loaded, tensioning mechanism and it will go (see Figure 5).
UPPER BLADE GUIDES
= ...
Operation Manual - Page 7
... can strip teeth from bearing.
If hands slip, they could contact blade. • Try to stand to keep workpiece flat against table and guided along desired path. • ...radius. The type of upper guide until it clears workpiece by ¼". CONTOUR SAWING
When contour sawing, use a blade with more than 5" needs proper support.
Loosen upper guide knob (Figure 10, Key No. 25) and...
Operation Manual - Page 8
...tilting table to desired
degree. • Unlock table by loosening locking handle located on band saw with
blade to properly remove foreign particles from power source before cut in contact with...threaded or sliding surfaces.
• Occasionally apply a coat of foreign particles.
• Operate band saw .
• Keep wheels clean. Do not allow
sawdust to accumulate on
the backside of the...
Operation Manual - Page 9
... at weld
1. Blade guide brackets loose
Teeth ripping from workpiece
5. Vibrating workpiece 4. Teeth filling with finer blade
Blade is binding blade 2. Excessive dirt and chips
Saw will not start
Loose electrical connections
1. Replace 3. Adjust blade guides; Clean thoroughly Have qualified electrician check electrical connections
9 Blade too coarse for wheel diameter
6. Gently...
Operation Manual - Page 13
... Support Tracking Adjustment Bracket Idler Shaft
6000ZZ Ball Bearing* 3BMI-26 Retaining Ring Idler Wheel Wheel Band
3AMI-IO Retaining Ring 6-1.0 x lOmm Hex Head Bolt* Driven Shaft Driven Pulley Lower Wheel ...Cabinet Blade 62"Long 6-1.0mm Hex Nut* Seal 5-0.8 x 6mm Socket Head Bolt
Operator's Manual Hardware Bag
* Standard hardware item available locally. O0 STD870510 25108.
O0 25109.00 25110....
Operation Manual - Page 24
... equipment, or heating and cooling systems,
no matter who made it, no matter who sold it -yourself. For the replacement parts, accessories and owner's manuals that you need to do-it ! se a rs. Your Home
For expert troubleshooting and home solutions advice:
www.managemyhome.com
For repair - in items like garage door...
Similar Questions
Repairing Broken Drive Belt On Craftman Band Saw Model 351.214190
How To Remove The Lower Wheel On Craftman Band saw Model 351.214190. Because The Drive Belt Is broke...
How To Remove The Lower Wheel On Craftman Band saw Model 351.214190. Because The Drive Belt Is broke...
(Posted by AVERBECK 9 years ago)
Remove Driven Pulley On Band Saw Model 351.214190
How Do You Remove Driver Pulley On Band Saw Model351.214190
How Do You Remove Driver Pulley On Band Saw Model351.214190
(Posted by AVERBECK 9 years ago)
Where Can I Get A Belt For A 9' Craftsman Band Saw Model 351.214190?
I located one at sears parts direct, but it is running $26.00 and that seems a little high for the b...
I located one at sears parts direct, but it is running $26.00 and that seems a little high for the b...
(Posted by manny22002 11 years ago)
Registration With Help-owl
Help Owl asks me to type a "code" into a MINI-SIZED rectangle.... but NO CLUE of WHAT to type. BU...
Help Owl asks me to type a "code" into a MINI-SIZED rectangle.... but NO CLUE of WHAT to type. BU...
(Posted by dubldee9 11 years ago)
How Do I Adjust My 21400 Band Saw Blade?
I don't have an owners manual and Craftsmen doesn't have one on line.
I don't have an owners manual and Craftsmen doesn't have one on line.
(Posted by jbehling 12 years ago)