Home » Craftsman » Tools » Craftsman 21419

Craftsman 21419 Support Question

Find answers below for this question about Craftsman 21419 - 9 in. Band Saw.
Need a Craftsman 21419 manual? We have 1 online manual for this item!

Craftsman Overview Questions Manuals Reviews Videos Research

Question posted by AVERBECK on April 24th, 2014

Remove Driven Pulley On Band Saw Model 351.214190

How Do You Remove Driver Pulley On Band Saw Model351.214190

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Craftsman 21419 Manual Pages

Operation Manual - Page 1

Sears, Roebuck and Co., Hoffman www.sears.comlcraftsman 25126,03 Draft (01/18/08) Estates, IL 60179 U.S.A. perator's nual ® tP BENCH TOP BAND SAW Model No. 351.214190 CAUTION: Read and follow all Safety Rules and Operating instructions before First Use of this Product.

Operation Manual - Page 2

... apply for which it was not designed. • Disconnect tool when changing blade. © Sears, Roebuck and Co. 2 Remove adjusting tools. Check to determine that being careless for alignment of moving ..., master switches or remove switch keys to cause cancer, birth defects or other masonry products. PROPOSITION 65 WARNING: Some dust created by power sanding, sawing, grinding, drilling and...

Operation Manual - Page 3

... Washer D Table Locking Insert Assembly may deteriorate these finishes. Check for completeness. The band saw . WARNING: Never use highly volatile solvents. If predrilled holes do not leave tool until it stuck in . Remove knob assembly (Key Nos. 16, 17 and 18) from saw frame. • Position table assembly on package) before plugging in the work...

Operation Manual - Page 4

POWER SOURCE The motor is designed for operation on voltages which accept the tool plug. Remove the key to prevent unauthorized use a 3-prong to a live terminal.... unless permitted by a qualified electrician. Up to insure durability. The Craftsman 9" Bench Top Band Saw features welded steel frame construction and a solid cast iron table surface to 50 ft 16 NOTE: Using extension cords...

Operation Manual - Page 5

..., slide key into the slot on the left front of the tool and open upper and lower doors. The saw OFF, push the switch to the up position. Locking Switch in OFF Position REMOVING BLADE WARNING: Disconnect band saw column. Wear leather gloves when handling band saw ON, pull the switch to the down position. NOTE: When...

Operation Manual - Page 6

... is removed, every adjustment should not touch blade when no workpiece is in clockwise direction. Track blade as described in the following section. Do not perform tracking adjustment while band saw is ...tensioned and tracked. • Blade guides support blade at sides and rear of the tool frame is tracking properly, secure position by tightening screws. 6 Slide blade in the ...

Operation Manual - Page 7

...8226; There should be in line with cut determines number of material being performed. CONTOUR SAWING When contour sawing, use hands over 7 Avoid positioning hands in contact with more detrimental, use a ...least three teeth in contact with blade. BLADE PITCH Pitch describes number of blade by tilting saw and use both hands to avoid shocking blade. A blade with work. ® For...

Operation Manual - Page 8

... Refer to Figure 10. • Perform bevel cutting by tilting table to desired degree. • Unlock table by loosening locking handle located on band saw with blade to properly remove foreign particles from power source before cut in any way, have it slick and corrosion free. Do not allow sawdust to accumulate on...

Operation Manual - Page 9

... at weld 1. Blade guides or bearings not adjusted properly 4. Excessive dirt and chips Saw will not start Loose electrical connections 1. Tighten properly 1. Use blade with finer teeth ...of feed too great 3. Inadequate feed pressure 3. Hold workpiece firmly 4. Blade too coarse 1. Remove blade, twist inside out and reinstall blade Crooked cuts Rough cuts 1. Blade too coarse for work...

Operation Manual - Page 11

Recommended Accessories A Multi-Purpose Stand 2, Blade 62" x W' x 14TPI Hook A Blade 62" x 1/4"x 6TPI Hook A Blade 62" x 3/8,x, 4TPI Hook Model No. 9-22224 9-21792 9-21793 9-21794 KEY NO. 30 31 32 33 34 35 36 37 PART NO. N/A 25080.00 25767.00 25081.00 25082.00 ...

Operation Manual - Page 13

... Bracket Idler Shaft 6000ZZ Ball Bearing* 3BMI-26 Retaining Ring Idler Wheel Wheel Band 3AMI-IO Retaining Ring 6-1.0 x lOmm Hex Head Bolt* Driven Shaft Driven Pulley Lower Wheel 5-0.8 x 12mm Socket Head Bolt* Belt 5-0.8 x lOmm Button Head Screw 5mm Flat Washer* Motor Pulley Cabinet Blade 62"Long 6-1.0mm Hex Nut* Seal 5-0.8 x 6mm Socket Head Bolt Operator...