Craftsman 21400 Support Question
Craftsman 21400 Support Question
Find answers below for this question about Craftsman 21400 - 10 in. Band Saw.Need a Craftsman 21400 manual? We have 1 online manual for this item!
Question posted by jbehling on November 2nd, 2011
How Do I Adjust My 21400 Band Saw Blade?
I don't have an owners manual and Craftsmen doesn't have one on line.
Current Answers
Related Craftsman 21400 Manual Pages
Owners Manual - Page 1
... Operating Instructions.
• Table of Contents
• Full One Year Warranty • Safety Instructions • Assembly • Getting to Know Your Bandsaw • Adjustment • Operation • Maintenance
• Troubleshooting • Electrical Schematic • Parts List
• EspaSol, p. 12
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Owner's Manual
10-in.
Owners Manual - Page 2
...owner's manual carefully. Never use an adapter to accommodate a two-pronged receptacle, you may also have other rights, which vary, from Tools after Use. Always Remove the Adjusting... to know your bandsaw 5
Adjustment ...
6
Operation ...
8
Maintenance ...
8
Troubleshooting ...
9
Electrical schematic ...
9
Parts list ...
10
Esparlol 12
If this Craftsman tool fails due to a defect ...
Owners Manual - Page 3
... be backed out of time. 10. Rubber-soled footwear is accidentally contacted.
_ I_,
Always Disconnect Tools. Always Check for Damaged Parts. Make sure that might get caught in cord. Never attempt to be used . 4.
Never wear loose clothing or jewelry that the blade tension and blade tracking are properly adjusted. 8, Make "relief" cuts before servicing...
Owners Manual - Page 4
...
Owner's Manual 1
Upper Table Trunnion Assembly 1 Bag of the table (See Fig. 1). M3 Hex %" Wrench 1
C
A'
!B
D
E
F
G
=====_=_
M5He x" L" Wrench 1
2. Assemble the upper table trunnion to be installed: Table, Blade ...when passing the saw blade through the slot of Loose Parts 1
..._J
Hex.
Prior to use this machine until all parts thoroughly with adjustable wrench. Apply ...
Owners Manual - Page 5
... a suitable dust collector.
To ensure sufficient upright stability of the machine it should be
bolted to the saw blade. Lay the rip fence onto the guide rail. Tighten rip fence handle by pressing downward. (See Fig. 3)
FIG. 5
f. b. d. FIG. 6
tension knob =g knob
]uide
T
_. _
_Blade
rack ng knob
'Guide post adjusting knob ,
Lower tabl Dust
Owners Manual - Page 6
... indicator accordingly by making trial cuts in the center.
Tighten the hex. CHANGING AND ADJUSTING THE SAW BLADE
This bandsaw is factory-equipped with a general-purpose wood cutting blade, the saw blade.(See Fig.8)
FIG. 10
b.
Loosen the screw securing the indicator and reset if necessary to the upper table trunnion. (See Fig. 7)
3. Using a wrench, release the...
Owners Manual - Page 7
... guides relative to within 1/32" of the saw blade. c. b. The upper blade guide should run in the center of the saw blade.
When the correct adjustment is installed and tensioned, track the saw blade by adjusting the tracking knob by releasing the guide adjusting screw (A) Fig. 15 on each side of the saw blade, proceed as this will adversely affect the life...
Owners Manual - Page 8
... a M6 hex. "L" wrench (not 15rovided) to the saw blade, they should be sharp.
The saw blade, etc.) clean to clean the bandsaw. The rip fence is to unexpected starting, before starting check if any part of the workpiece, usually in line with the guide adjusting screw (D) Fig.16
Guide adjusting screw (C)
9. With both hands, firmly hold the...
Owners Manual - Page 9
... into the housing.
1. Adjust the blade tracking knob (See ADJUSTMENT instructions). 3. W.b_rI,NING: This machine must be properly positioned on . The saw blade was put less pressure on the workpiece.
The blade tension knob has not been tightened. 2. The saw blade does not move with a vacuum cleaner. The saw blade, use .
2. The wheels are not in a straight line. Check the cable...
Owners Manual - Page 11
...Ring 12 Saw Blade Upper Wheel
Upper Bearing Bolt Wheel Carrier Bracket Hex. Nut M14 Star Lock Mount Shaft Blade Tensioner
...Adjusting Knob Cap Blade Tracking Knob Cap
Blade Tracking Knob Body Hex. Bolt M6x20
Guide Adjust Screw Ball Bearing 6ram
Guide Key Washer 6
Lock Nut M6
Spring Washer 6 Tongue Lock Special Nut M22 Lower Door
Leaf Spring Rivet 4X8
Lock Housing Special Spring Washer 10...
Owners Manual - Page 20
...SM Marca de Servicio de Sears, Roebuck and Co. For the replacement parts, accessories and owner's manuals that you need to do-it !
Your Home
For repair-in items like garage door openers...(U.S.A. only) www.sears.com
To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on -line for the location of your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, ...
Similar Questions
Remove Driven Pulley On Band Saw Model 351.214190
How Do You Remove Driver Pulley On Band Saw Model351.214190
How Do You Remove Driver Pulley On Band Saw Model351.214190
(Posted by AVERBECK 10 years ago)
What Would It Cost To Ship This Saw To St. John`s Newfoundland Canada?
(Posted by thomasa39 11 years ago)
Manual For My Craftsman 9' Band Saw
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.Th...
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.Th...
(Posted by glorioussuhn37 11 years ago)
Craftsman 21400 Maker
Is this saw actually a Rikon, or a Jet. Or, is there a difference?
Is this saw actually a Rikon, or a Jet. Or, is there a difference?
(Posted by rcpozzi63 11 years ago)
Blades
I got an older Craftsman 10in Band Saw with no blade. I mesured around the three wheels and got 28 i...
I got an older Craftsman 10in Band Saw with no blade. I mesured around the three wheels and got 28 i...
(Posted by neuleib 13 years ago)