Craftsman 21400 Support Question
Craftsman 21400 Support Question
Find answers below for this question about Craftsman 21400 - 10 in. Band Saw.Need a Craftsman 21400 manual? We have 1 online manual for this item!
Question posted by neuleib on May 1st, 2011
Blades
I got an older Craftsman 10in Band Saw with no blade. I mesured around the three wheels and got 28 inches. What size blade do I need?
Thank you, Lyle Neuleib
[email protected]
Current Answers
Answer #1: Posted by frankdonnelly on July 20th, 2012 2:37 PM
frankdonnelly
Member since:
July 20th, 2012 Points: 0
Member since:
July 20th, 2012 Points: 0
Check www.sawblade.com . Their first-rate customer service staff will gladly answer your inquiries about the right blade for your needs.
Related Craftsman 21400 Manual Pages
Owners Manual - Page 1
www.craftsman.com Owner's Manual
10-in. BANDSAW
1/3 HP MOTOR Model 119.214000
CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions.
• ...
Owners Manual - Page 2
... for only ninety days from the date of purchase. Read the owner's manual carefully. Always Ground All Tools. If your bandsaw 5
Adjustment ...
6
Operation ...
8
Maintenance ...
8
Troubleshooting ...
9
Electrical schematic ...
9
Parts list ...
10
Esparlol 12
If this Craftsman tool fails due to a defect in material or workmanship within one year warranty ...
2
Safety instructions...
Owners Manual - Page 3
..., and cutters. Check for proper blade size and type for alignment of moving parts, binding of time. 10. Also use a,face or dust mask if the cutting operation is accidentally contacted.
_ I_,
Always Disconnect Tools. Never Stand on the lower door. AlwaysWearProperApparel. Rubber-soled footwear is to saw will operate properly and perform its intended...
Owners Manual - Page 4
... "Table of loose parts. Separate all items are assembled and working properly. CARTON CONTENTS
Item A B C D
E F G
Description
Q'ty.
Blade Tension Knob 1
Miter Gauge 1.
2.
a.
a. TOOLS REQUIRED FOR ASSEMBLY
Item
Description
Q'ty. UNPACKING AND CHECKING CONTENTS
Model 119.214000 10" Bandsaw is supplied partly assembled. Use any packing material. M3 Hex %" Wrench...
Owners Manual - Page 5
..._. _
_Blade
rack ng knob
'Guide post adjusting knob ,
Lower tabl Dust To ensure sufficient upright stability of the machine it should be
bolted to the saw blade. The bandsaw has a 2-1/2" dust port included. (Sea Fig. 6) It is connected to a suitable dust collector.
Fastetnheguiderailwithtwoeachstarknobscrewandwasher
FIG, 4
tothetableU. eeFig.2)
e. For this purpose 6mm holes
are...
Owners Manual - Page 6
... fence handle such that the indicator reads
zero degree on the lower table trunnion and place a suitably sized square against the saw blade is factory-equipped with a general-purpose wood cutting blade, the saw blade. CHANGING AND ADJUSTING THE SAW BLADE
This bandsaw is set prior to delivery. Loosen the four hex.,bolts mounting the table to decrease...
Owners Manual - Page 7
.... Tightetnhewingnutaftersetting. Re-tension the new saw blade and check the saw blade before reconnecting the power supply.
6. b.
e. Guide post adjusting knob
FIG. 14
8. Set both roller guides are pointing downwards and towards you at the side of the saw blade from the upper and lower wheels.
If need adjust the tracking of the upper wheel housing. (See Fig. 14...
Owners Manual - Page 8
... downstroke, To avoid injury when hands are seated correctly before restoring power to get stuck, or the saw blade. For best results the saw blade, they should be made. Start the bandsaw by turning the blade tension knob on it , as this wheel. Regular maintenance of all moving parts and prevent excessive wear. e. d.
Use a fine tooth...
Owners Manual - Page 9
.... The table is not at 45 or 90 degrees.
Defective motor.
1. Replace the belt.
1. Clean the machine regularly. Clean the ventilating slots of the wheels. 3. Replace the saw blade or put on the bandsaw. W.b_rI,NING: This machine must be done only by cutting hard material or long use a 6 "EEl. Problem The machine...
Owners Manual - Page 11
...;
Flat Countersunk Rod Guide Guide Rail Fence Carrier
Head Screw M6x1O
,Special Screw Washer 10 Fence Handle Roll Pin 3x18
Star knob screw Washer 6 Aluminium Bar
Miter Gauge Base ... Set Screw M6xlO Drive Belt
Ball Bearing 12ram Retaining Ring 28 Lower Wheel Tire
Retaining Ring 12 Saw Blade Upper Wheel
Upper Bearing Bolt Wheel Carrier Bracket Hex. Bolt M6x60
Hex. Socket Set Screw Upper...
Owners Manual - Page 20
...; Marca Registrada / TM Marca de F&bdca / SM Marca de Servicio de Sears, Roebuck and Co.
For the replacement parts, accessories and owner's manuals that you need to do-it fixed, at your nearest
Sears Parts & Repair Center.
1-800-488-1222
Call anytime, day or night (U.S.A. MCMarque de commerce / MDMarque depos6e de...
Similar Questions
Zts 6000 Mower Dies When Try To Lower/raise Deck Or Engage Blades.
I have a ZTS 6000 zero turn craftsman mower. When I try to move deck or engage blades the mower dies...
I have a ZTS 6000 zero turn craftsman mower. When I try to move deck or engage blades the mower dies...
(Posted by dtaylor717 8 years ago)
What Is A Sears Electronic 10'table Saw Worth
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
(Posted by mastercook76 11 years ago)
Craftsman 21400 Maker
Is this saw actually a Rikon, or a Jet. Or, is there a difference?
Is this saw actually a Rikon, or a Jet. Or, is there a difference?
(Posted by rcpozzi63 12 years ago)
Miter Gauge Substitute On 137218070 Craftsman
Are there better miter gauges that will work on the137218070 Craftsman 10" table saw. The original i...
Are there better miter gauges that will work on the137218070 Craftsman 10" table saw. The original i...
(Posted by anoka114 12 years ago)
How Do I Adjust My 21400 Band Saw Blade?
I don't have an owners manual and Craftsmen doesn't have one on line.
I don't have an owners manual and Craftsmen doesn't have one on line.
(Posted by jbehling 12 years ago)