Craftsman 21400 Support Question
Craftsman 21400 Support Question
Find answers below for this question about Craftsman 21400 - 10 in. Band Saw.Need a Craftsman 21400 manual? We have 1 online manual for this item!
Question posted by rcpozzi63 on May 23rd, 2012
Craftsman 21400 Maker
Is this saw actually a Rikon, or a Jet.
Or, is there a difference?
Current Answers
Related Craftsman 21400 Manual Pages
Owners Manual - Page 1
www.craftsman.com Owner's Manual
10-in. BANDSAW
1/3 HP MOTOR Model 119.214000
CAUTION: Before using this product, read this manual and follow all its Safety Rules and Operating Instructions.
• ...
Owners Manual - Page 2
...5
Adjustment ...
6
Operation ...
8
Maintenance ...
8
Troubleshooting ...
9
Electrical schematic ...
9
Parts list ...
10
Esparlol 12
If this warranty will apply for only ninety days from the date of purchase. Always Avoid Dangerous Environments.
If this tool is used for commercial or rental purposes, this Craftsman tool fails due to a defect in material or workmanship within one...
Owners Manual - Page 3
...suitable support is recommended for Damaged Parts.
Never attempt to be backed out of time. 10.
will not be properly repaired or replaced.
_PECIAL SAFETY RULES FOR BANDSAWS
1. Always turn... . 4. Release blade tension when the saw stock that appear on Tools. Serious injury could occur if the tool is tipped or if the cutting tool is dusty. AlwaysWearProperApparel. Never Stand on...
Owners Manual - Page 4
UNPACKING AND CHECKING CONTENTS
Model 119.214000 10" Bandsaw is applied to the table. Remove the ...x" L" Wrench 1
2.
INITIAL ASSEMBLY
The machine is supplied partly assembled. Blade Tension Knob 1
Miter Gauge 1.
2. Apply a coat of loose parts.
TOOLS REQUIRED FOR ASSEMBLY
Item
Description
Q'ty. a. Mount the table to the upper table trunnion, taking care when passing the...
Owners Manual - Page 5
... rail.
Tighten rip fence handle by pressing downward. (See Fig. 3)
FIG. 5
f. b. To ensure sufficient upright stability of the machine it should be
bolted to the saw blade. For this purpose 6mm holes
are provided in use, the bandsaw is connected to a suitable dust collector. The bandsaw has a 2-1/2" dust port included. (Sea...
Owners Manual - Page 6
... table into position and check that excessive pressure is set prior to the required angle and tighten the wing nut again (See Fig. 10). SETTING TABLE SQUARE TO SAW BLADE
Loosen the wing nut on the side of the rip fence has been factory-set the table to delivery. nut on the...
Owners Manual - Page 7
...set the roller guides too close as this will adversely affect the life of the saw blade passes through the table. Do not set the roller guides too close as...position the right and left roller guides relative to the table. a.Removteheripfencet,heguiderail,thewingnutandscrew fromthetable.
The saw blade
b. Replace the rip fence, the guide rail, the wing nut and screw to the...
Owners Manual - Page 8
... operation of the bandsaw will also make straight cuts.
Slowly feed the workpiece towards the saw blade, etc.) clean to enable safe and accurate crosscut of dust.
The tiltable table...
a. Using a M6 hex. "L" wrench (not 15rovided) to clean the bandsaw. d. Select the right saw blade, putting only light pressure on motor mounting flange. (See Fig. 17)
c. Do not attempt to...
Owners Manual - Page 9
.... 2.
Defective switch. 3 Defective motor.
1. Rip fence for breakage. 2. Feed rate too fast.
3. The teeth are dull, caused by a Cdalified electrician, usin genuine replacement parts. The saw blade does not cut at right angles to electrical system should be properly positioned on the workpiece.
1. Remedy
1. Replace the lock switch. 3. Open the doors...
Owners Manual - Page 11
...Washer 6 Tongue Lock Special Nut M22 Lower Door
Leaf Spring Rivet 4X8
Lock Housing Special Spring Washer 10 Slotted Insert Hex. Nut M6
Lower Bearing Bolt Hsx. Bolt M6x12 Lock Nut M6 Washer 6 Gear... 28 Lower Wheel Tire
Retaining Ring 12 Saw Blade Upper Wheel
Upper Bearing Bolt Wheel Carrier Bracket Hex. Nut M6
Slotted Insert
Special Spring Washer 10 Lock Housing Upper Door Rivet 4x8
Leaf ...
Similar Questions
What Would It Cost To Ship This Saw To St. John`s Newfoundland Canada?
(Posted by thomasa39 11 years ago)
What Is A Sears Electronic 10'table Saw Worth
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
(Posted by mastercook76 11 years ago)
Manual For My Craftsman 9' Band Saw
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.Th...
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.Th...
(Posted by glorioussuhn37 11 years ago)
How Do I Adjust My 21400 Band Saw Blade?
I don't have an owners manual and Craftsmen doesn't have one on line.
I don't have an owners manual and Craftsmen doesn't have one on line.
(Posted by jbehling 12 years ago)
Blades
I got an older Craftsman 10in Band Saw with no blade. I mesured around the three wheels and got 28 i...
I got an older Craftsman 10in Band Saw with no blade. I mesured around the three wheels and got 28 i...
(Posted by neuleib 13 years ago)