Craftsman 21400 Support Question
Craftsman 21400 Support Question
Find answers below for this question about Craftsman 21400 - 10 in. Band Saw.Need a Craftsman 21400 manual? We have 1 online manual for this item!
Question posted by jkinney6 on March 23rd, 2016
Engine Replacement For A 1955 Craftsman 131.8250.
I have an old craftsman lawn mower 1955, MN 131.8250 and would like to replace the engine. The old one was a 5.5 horse power. Is there an engine i can buy that will bolt on with same dementions?
Current Answers
Answer #1: Posted by BusterDoogen on March 23rd, 2016 12:13 PM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
Go here for the parts list to A-800 for the engine model 752101. Your model is old enough that there are very few parts available.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Craftsman 21400 Manual Pages
Owners Manual - Page 1
... • Operation • Maintenance
• Troubleshooting • Electrical Schematic • Parts List
• EspaSol, p. 12
Sears, Roebuck and Co., Hoffman Estates, IL 60179, U.S.A. Owner's Manual
10-in. www.craftsman.com
Owners Manual - Page 2
...
Operation ...
8
Maintenance ...
8
Troubleshooting ...
9
Electrical schematic ...
9
Parts list ...
10
Esparlol 12
If this Craftsman tool fails due to a defect in material or workmanship within one year from the date of ... Dept. 817WA, Hoffman Estates, IL 60179
GENERAL SAFETY WARNINGS
KNOW YOUR POWER TOOL. This warranty gives you specific legal rights, and you must plug it...
Owners Manual - Page 3
...pieces from the blade. 3.
Never Leave Tools Running Unattended. will not be backed out...10. j,_
Always Use Safety Glasses and Wear Hearing Protection.
AlwaysWearProperApparel. Rubber-soled footwear is to saw will operate properly and perform its intended function.
Never wear loose clothing or jewelry that
damaged parts should immediately be properly repaired or replaced...
Owners Manual - Page 4
...10" Bandsaw is shipped complete in each item with a clean dry cloth. b.
Lock Washer6 4 Star Knob Screw 2 Washer6 2.
Mount the table to the upper table trunnion and install a bolt...TOOLS REQUIRED FOR ASSEMBLY
Item
Description
Q'ty. Use any packing material. c. Bolt M6x12 4. Locate four hex bolts... trunnion, taking care when passing the saw blade through the slot of paste wax...
Owners Manual - Page 5
sethehexsockehteadcapscreww, ashearndwing
nutforcorrectinthgeworkintgableflatness(S. To ensure sufficient upright stability of the machine it should be
bolted to the saw blade. Tighten rip fence handle by pressing downward. (See Fig. 3)
FIG. 5
f.
The bandsaw has a 2-1/2" dust port included. (Sea Fig. 6) It is recommended that when in ...
Owners Manual - Page 6
...tilt the table, loosen the wing nut on the frame. (See Fig.8) b. bolt and adjust until the saw blade.(See Fig.8)
FIG. 10
b. Raise the fence handle to give zero degree reading. (See Fig. 9)
I...-purpose wood cutting blade, the saw blade or carrying out adjustments, switch the handsaw off and remove the power cord from the main outlet. To change the saw blade, the following procedure must ...
Owners Manual - Page 7
... towards you at the side of the saw blade before reconnecting the power supply.
6. Adjust the rear roller guide to within 1/32" of the saw blade by unlocking the guide adjusting screw ...tensioned, track the saw blade tracking by turning the upper wheel by turning the door locking knobs before setting the blade guides. SETTING THE CUTTING HEIGHT
a.
Replace the rip fence,...
Owners Manual - Page 8
... device or the power cord, turn the workpiece without pushing it until the particular part is to clean the bandsaw. Keep the inside (near to the saw blade to ensure accurate operation of the workpiece. b. Using a M6 hex. d. For best results the saw blade. The rip fence is properly repaired or replaced.
d. When the...
Owners Manual - Page 9
No power supply. 2. Defective switch. 3 Defective motor.
1. The drive belt has snapped. 1. Rip fence for breakage. 2. Feed rate too fast.
3. The table is normal
1. Defective motor.
1.
From time to time remove the sawdust to electrical system should be properly positioned on the workpiece.
1. Replace the saw blade or put on the wheels. Replace the saw blade...
Owners Manual - Page 11
...Retaining Ring 28 Lower Wheel Tire
Retaining Ring 12 Saw Blade Upper Wheel
Upper Bearing Bolt Wheel Carrier Bracket Hex. Nut M6
Cable w/...Lock Housing Special Spring Washer 10 Slotted Insert Hex. Bolt M6x45
Door locking knob body Hex. Bolt M6x12 Lower Table Trunion
Carriage Bolt M6x16 Wing Nut M6 Washer...120 121 122
123 124 125 126 127 128 129 130 131
132 133 134 135 136 137
138 ' 139 140 141...
Owners Manual - Page 20
...ca
Our Home
For repair of carry-in your home-of your home or ours!
For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. only) www.sears....Service Mark of home appliances and items like vacuums, lawn equipment, and electronics, call or go on-line for the location of all major brand appliances, lawn and garden equipment, or heating and cooling systems,
...
Similar Questions
What Would It Cost To Ship This Saw To St. John`s Newfoundland Canada?
(Posted by thomasa39 11 years ago)
What Is A Sears Electronic 10'table Saw Worth
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
what is a sears electronic 10" table saw w/ext,& base model 113.290650 worth?, it works great
(Posted by mastercook76 11 years ago)
Manual For My Craftsman 9' Band Saw
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.Th...
I'm looking for the manual for my band saw .I'ts a display in the store and they dont have manual.Th...
(Posted by glorioussuhn37 11 years ago)
How Do I Adjust My 21400 Band Saw Blade?
I don't have an owners manual and Craftsmen doesn't have one on line.
I don't have an owners manual and Craftsmen doesn't have one on line.
(Posted by jbehling 12 years ago)
Blades
I got an older Craftsman 10in Band Saw with no blade. I mesured around the three wheels and got 28 i...
I got an older Craftsman 10in Band Saw with no blade. I mesured around the three wheels and got 28 i...
(Posted by neuleib 13 years ago)