Brother International PE770 Support Question
Brother International PE770 Support Question
Find answers below for this question about Brother International PE770 - Computerized Embroidery Machine.Need a Brother International PE770 manual? We have 3 online manuals for this item!
Question posted by toddmcatee on February 16th, 2012
Holding Up To Embroidering Onesies About 15-20 Per Month
will this machine hold up to embroidering 15-20 onesies per month
Current Answers
Answer #1: Posted by tmckelvey82 on February 16th, 2012 7:21 PM
tmckelvey82
Member since:
November 2nd, 2011 Points: 359,840
Member since:
November 2nd, 2011 Points: 359,840
Brother is one of the sturdiest and highest quality machines you can buy short of going industrial. With proper regular maintenance, it should do fine. Good luck!
Please be sure to accept this answer and mark as helpful.
Not the answer you were looking for? Then please feel free to resubmit!
Thank you!
Related Brother International PE770 Manual Pages
Users Manual - English - Page 1
GETTING READY EMBROIDERY APPENDIX
Computerized Embroidery Machine
Operation Manual
Users Manual - English - Page 5
...14 Attaching the Embroidery Unit 15
Embroidery unit precautions ...15 Attaching the embroidery unit ...15 Removing the embroidery unit ...16
Turning the Machine On/Off 18
Power supply precautions ...18
Turning on the machine ...19 Turning off the machine ...19
LCD (Liquid Crystal Display) Operation 20
Viewing the LCD...20
Changing the machine settings ...21
Checking machine operating procedures...
Users Manual - English - Page 6
... partway through a design...65 Stopping while embroidering ...66
Bobbin Case Adjustment 68
Correct tension...68 Bobbin thread is loose...68 Bobbin thread is tight ...68
APPENDIX
69
Care and Maintenance ...70
Cleaning the machine surface ...70 Cleaning the race ...70
Attaching the Embroidery Foot 72
Attaching the embroidery Foot "Q" ...72
Troubleshooting ...74
Error messages...
Users Manual - English - Page 7
...bobbin You can quickly be accessed for the correct operation of the various functions. Before using the machine, carefully read the "IMPORTANT SAFETY INSTRUCTIONS", and then study this embroidery machine.
In addition, after embroidering (page 51).
d Embroidery You can quickly and easily be cut automatically after you for purchasing this manual for future reference. Introduction...
Users Manual - English - Page 8
Part Name
10 Spool net
11 Operation manual
12 Quick reference guide
13
Embroidery foot "Q" (on machine)
Embroidery set
4 Cleaning brush 5 Screwdriver (large) 6 Screwdriver (small) 7 Spool... (4)
3 Needle set (large) 14 H 18cm X W 13 cm
(H 7 inches X W 5 inches)
15 Scissors 16 Dust cover 17 Accessory bag
Part Code
U.S.A. / Canada
Others
XA5523-020
XD1628-121
XD1629-021
XD0474-151...
Users Manual - English - Page 11
... machine. d Air vent The air vent allows the air surrounding the motor to thread the needle. Needle and embroidery foot section
Right-side/rear view
a Thread guide disk Pass the thread through the thread guide disk when using the needle threader to be exchanged. f Embroidery foot "Q" This presser foot is being used for embroidering...
Users Manual - English - Page 13
... (liquid crystal display) and operation keys. For details, refer to store patterns in the machine's memory. d Next page key Press to get help on the LCD.
e Memory key Press to "LCD (Liquid Crystal Display) Operation" (page 20). g
f Embroidery key Press to display the settings screen. g Settings key Press to display the pattern type...
Users Manual - English - Page 15
...Embroidery Unit 15
Embroidery unit precautions 15 Attaching the embroidery unit 15 Removing the embroidery unit 16 Turning the Machine On/Off 18 Power supply precautions 18 Turning on the machine 19 Turning off the machine 19 LCD (Liquid Crystal Display) Operation 20 Viewing the LCD 20 Changing the machine settings 21 Checking machine... start embroidering are described in this chapter.
Users Manual - English - Page 16
... adjust the size and position of the embroidery pattern. GETTING READY
Embroidery Step by Step
The basic steps for embroidery are as follows.
1
Attaching the embroidery unit
Attach the embroidery unit. (If the embroidery unit is not attached, the machine does not operate.) For details, refer to "Attaching the embroidery unit" (page 15).
↓
2 Checking the needle
Use a needle...
Users Manual - English - Page 17
... the embroidery unit
Cautions for the embroidery unit will be dropped and cause injury.
● Keep your hands and other objects away from the embroidery carriage and frame.
Before turning on the embroidery carriage, and do not forcefully move the machine with the embroidery unit in the embroidery unit connector slot. Turn off the machine. Attaching the Embroidery Unit 15
Users Manual - English - Page 19
Hold the release button on the bottom left of
d the embroidery unit, and slowly pull the embroidery unit to the left.
1
a
a Release button
X The embroidery unit separates from the machine. Attaching the Embroidery Unit 17 CAUTION
● Do not carry the embroidery unit by holding the release button compartment.
Users Manual - English - Page 34
... thread behind the needle bar thread guide by holding the thread in the order shown below.
1
a Shutter
Note
z If the embroidery foot has been lowered and the shutter is correctly fed through the take -up lever. Memo
z The needle threader can easily be used with sewing machine needles 75/11 through this window and...
Users Manual - English - Page 36
...machine to the needle bar thread a guide.
• For details, refer to start embroidering. GETTING READY
Raise the presser foot lever, pass the end of 130/20 or thicker which cannot be used with a thickness of the e thread through the embroidery... lever
Pass the thread through the eye of the d thread through the embroidery foot hole.
Raise the presser foot lever, pass the end of the ...
Users Manual - English - Page 38
...machine starts embroidering.
Hold the needle with fabric or paper to prevent the needle from falling into the machine.
Lower the presser foot lever. GETTING READY
Replacing the needle
Place fabric or paper under the embroidery...with your left hand, and then e use a screwdriver to turn off the machine, otherwise injuries may be sure to turn the needle clamp
screw toward you (counterclockwise)...
Users Manual - English - Page 42
..., use stabilizer for embroidery machines. If there is not space, do not embroider the fabric.
To check the fabric thickness, attach the embroidery frame to prevent poor quality embroidery designs.
■ Fabric Prepare the fabric for embroidery to the fabric to the embroidery unit, and use the embroidery bobbin thread.
EMBROIDERY
Embroidering Neatly
This section describes...
Users Manual - English - Page 53
... one stitch
Forward one color
Forward one stitch (if pressed continuously, 9 stitches to 20 stitches) at the end of each character, the upper thread is not embroidered or when restarting the machine after power has been turned off in character embroidery. Selecting Embroidery Patterns 51 This is used . ■ LCD button
When a specific pattern is...
Users Manual - English - Page 74
... sure to the presser foot bar.
1
2
a Embroidery foot bar b Needle clamp screw
72
Hold the embroidery foot with your index finger wrapped around the lever at the back of purchase, the presser foot lever
is accidentally pressed and the machine starts embroidering. a
1
a Needle position button
Turn off the machine, otherwise injuries may hit the presser foot...
Users Manual - English - Page 78
...noise is not turned on it.
Incorrect bobbins will disappear.
The machine is made
while embroidering. Nothing appears on the machine.
Embroidery unit does not move.
page 24
page 32 page 36 page 64...the bobbin case. Dust has collected on . page 19 page 81 page 20 page 49 page 15
page 70
76 Replace the needle. Replace the bobbin case.
APPENDIX
Symptom
Probable...
Users Manual - English - Page 85
... operation 20 50
3
bobbin winding 24
bobbin winding thread guide 8
M
Brother poly #90 bobbin thread 7
buzzer 82
machine settings 21
, main power switch 9 19
C
characters 52
maintenance 70
manual needle threading 34
, memory key 11 63
cleaning 70
cleaning brush 6
N
D
dust cover 6
E
, embroidery card 7 55
embroidery card slot 9
, Embroidery foot "Q 6 9
embroidery foot...
USB GUIDE - Multi - Page 3
... 90 degrees. • .pes files saved with a stitch density that is not attached, the machine will begin flashing
after the media is inserted into your computer or machine, and may take about 5 to 6 seconds before the media is more than our original patterns, the thread or needle may cause the embroidery machine to the instruction...
Similar Questions
Brother Pe 770 Embroidery Machine
Can you provide the touch screen panel part number for the brother pe770 embroidery machine?
Can you provide the touch screen panel part number for the brother pe770 embroidery machine?
(Posted by sandymichelle144 1 year ago)
Lb 6770 Prw Sewing And Embroidery Machine
I am trying to find a memory card for embroidery designs to use in LB6770 PRW sewing and embroidery ...
I am trying to find a memory card for embroidery designs to use in LB6770 PRW sewing and embroidery ...
(Posted by rfdp47 2 years ago)
Brother Pe770 Embroidery Machine
I have a Brother PE770 Embroidery Machine, what are the best stitch settings?
I have a Brother PE770 Embroidery Machine, what are the best stitch settings?
(Posted by leeplantation08 10 years ago)
Embroidery Machine Se270d
I recently opened my brother se270d embroidery machine and looks like all the accessories are missin...
I recently opened my brother se270d embroidery machine and looks like all the accessories are missin...
(Posted by anngeeburns82 11 years ago)