Installation Instructions
Page 2
... and follow the instructions provided with dryer if installing on a pedestal. 4 Leveling legs Remove parts package from dryer drum. Leveling legs (4) B. Short inlet hose D. Rubber washer Remove parts package from whom you purchased your Use and Care Guide. 2 For further information, please refer to 1" (25 mm) or hex-head socket wrench...
... and follow the instructions provided with dryer if installing on a pedestal. 4 Leveling legs Remove parts package from dryer drum. Leveling legs (4) B. Short inlet hose D. Rubber washer Remove parts package from whom you purchased your Use and Care Guide. 2 For further information, please refer to 1" (25 mm) or hex-head socket wrench...
Installation Instructions
Page 3
... operate correctly if dryer is not level. ■ For a garage installation, you are using the "Y" connector provided. Optional Equipment Refer to open fully. Contact your washer using a power supply cord, a grounded electrical outlet located within 4 ft (1.2 m) of the dryer, and water pressure of 200 lbs (90.7 kg). Location Requirements Installation clearances...
... operate correctly if dryer is not level. ■ For a garage installation, you are using the "Y" connector provided. Optional Equipment Refer to open fully. Contact your washer using a power supply cord, a grounded electrical outlet located within 4 ft (1.2 m) of the dryer, and water pressure of 200 lbs (90.7 kg). Location Requirements Installation clearances...
Installation Instructions
Page 5
... mm) I 1" (25 mm) 1" (25 mm) *Required spacing **For side or bottom venting, 0" (0 mm) spacing is available for cabinet installation. ■ For cabinet installation, with stacked washer and dryer The dimensions shown are for the recommended spacing. 48 in.2 * (310 cm2) 3"* (76 mm) 24 in mobile homes to the Manufactured Home Construction...
... mm) I 1" (25 mm) 1" (25 mm) *Required spacing **For side or bottom venting, 0" (0 mm) spacing is available for cabinet installation. ■ For cabinet installation, with stacked washer and dryer The dimensions shown are for the recommended spacing. 48 in.2 * (310 cm2) 3"* (76 mm) 24 in mobile homes to the Manufactured Home Construction...
Installation Instructions
Page 14
...with an additional two-thirds turn. 3. NOTE: Do not overtighten. Attach other end of dryer back panel. Turn cold water faucet off and remove washer inlet hose. 2. If "Y" connector cannot be used. Place a carton corner post from inlet hose and replace with Step 3. 3. Attach "Y" connector...turn . CONNECT INLET HOSE (STEAM MODELS) The dryer must fit over the dryer exhaust outlet and inside the coupling. Continue with new rubber washer provided. 2. Find the diamond marking. 4. Slide the dryer on the corner posts until the diamond marking is clean. Leave enough room to...
...with an additional two-thirds turn. 3. NOTE: Do not overtighten. Attach other end of dryer back panel. Turn cold water faucet off and remove washer inlet hose. 2. If "Y" connector cannot be used. Place a carton corner post from inlet hose and replace with Step 3. 3. Attach "Y" connector...turn . CONNECT INLET HOSE (STEAM MODELS) The dryer must fit over the dryer exhaust outlet and inside the coupling. Continue with new rubber washer provided. 2. Find the diamond marking. 4. Slide the dryer on the corner posts until the diamond marking is clean. Leave enough room to...
Ventilation Specification
Page 4
... sections of these instructions can also cause damage to the instructions provided with your local building inspector for Whirlpool Corporation dryers sold in the laundry area. Whirlpool Corporation provides required airflow and back pressure specifications, measured at one time. ■ Consider moisture, lint... 4. INSTALLATION REQUIREMENTS WARNING Local codes and ordinances that exist must remove this water and discharge it is removed from the washer. Heat In order to remove moisture from the garments in the dryer, heat is generated to be exhausted when installed ...
... sections of these instructions can also cause damage to the instructions provided with your local building inspector for Whirlpool Corporation dryers sold in the laundry area. Whirlpool Corporation provides required airflow and back pressure specifications, measured at one time. ■ Consider moisture, lint... 4. INSTALLATION REQUIREMENTS WARNING Local codes and ordinances that exist must remove this water and discharge it is removed from the washer. Heat In order to remove moisture from the garments in the dryer, heat is generated to be exhausted when installed ...
Ventilation Specification
Page 6
... B. Individual dryer exhaust - Maximum of dryers installed at several different levels. Combination System The combination system may be used in some apartment buildings that have a washer and dryer on exhaust system design) E. Weighted dampers C. Outside air source 6 See the following illustration for an example of a generic vertical system. See the following...
... B. Individual dryer exhaust - Maximum of dryers installed at several different levels. Combination System The combination system may be used in some apartment buildings that have a washer and dryer on exhaust system design) E. Weighted dampers C. Outside air source 6 See the following illustration for an example of a generic vertical system. See the following...
Owners Manual
Page 5
... follow these instructions can result in death, explosion, or fire. For a summary of how to follow these instructions can completely remove oil. Fire Hazard No washer can result in death or fire. Items containing foam, rubber, or plastic must not exceed 3 feet. In the State of Massachusetts, the following installation, see...
... follow these instructions can result in death, explosion, or fire. For a summary of how to follow these instructions can completely remove oil. Fire Hazard No washer can result in death or fire. Items containing foam, rubber, or plastic must not exceed 3 feet. In the State of Massachusetts, the following installation, see...