Whirlpool WGD9600TA Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WGD9600TA manuals!
Problems with Whirlpool WGD9600TA?
Ask a Question
Free Whirlpool WGD9600TA manuals!
Problems with Whirlpool WGD9600TA?
Ask a Question
Most Recent Whirlpool WGD9600TA Questions
Start Button Gas Dryer Model Wgd9600ta
The start button of my Whirlpool gas dryer popped out. It seems that the little plastic knob can not...
The start button of my Whirlpool gas dryer popped out. It seems that the little plastic knob can not...
(Posted by fchart47 7 years ago)
Dryer Won't Heat
(Posted by Scottdarrenoxford 10 years ago)
Popular Whirlpool WGD9600TA Manual Pages
Owners Manual - Page 2
...; Features and specifications on our full line of your Yellow Pages telephone directory.
Our consultants provide assistance with the same precision used to local dealers, repair parts distributors, and service companies.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check "Troubleshooting." These parts will help , follow the instructions below. For...
Owners Manual - Page 4
... you use a gas detector approved by a qualified installer, service agency, or the gas supplier. The dryer must be detected by smell. Follow the gas supplier's
instructions.
• If you smell gas" instructions.
4 Do not store or use any phone in your gas supplier from a neighbor's phone. WARNING: Gas leaks cannot always be electrically grounded in accordance with local codes, or in the...
Owners Manual - Page 7
.... See Automatic Preset or Manual Preset Cycle Settings chart. Steam models
Non-Steam models
Cycle Control knob
Automatic Cycles Automatic Cycles allow you to match the cycle to complete drying, if needed . A sensor detects the moisture in the dryer too long.
Sanitize
Use this cycle for ironing
*Reset time to select a specific amount of 3 common infectious...
Owners Manual - Page 8
... option for the Enhanced Touch Up Cycle. The heat setting and cycle time are unable to alert you want to remove lightweight items in the
dryer for an extended
period.
*The Enhanced Touch Up Cycle... cycle is sprayed into the dryer drum after several minutes of the cycle.
The dryer will remain on while the water is selected.)
Damp Dry Signal On some models, the Damp Dry Signal may...
Owners Manual - Page 12
... fabric softener sheets blocking the grille? Dryer Operation
Dryer will not run cleaned.
■ "E" Variable (E1, E2, E3) service codes: Call for the dryer. See the Installation Instructions.
■ Is the clothing knotted or balled up , the load will turn, but you may be 2 household fuses or circuit breakers for service. Replace the fuse or reset the circuit breaker...
Owners Manual - Page 14
... state or province to published user or operator instructions and/or installation instructions.
2. Some states and provinces do not allow limitations on major appliances with electrical or plumbing codes, or use of products not approved by calling
Whirlpool. In Canada, call 1800253-1301. Replacement parts or repair labor if this major appliance is used in...
Installation Instructions - Page 3
...prevent property damage, personal injury, or death.
- IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1. do if you smell gas" instructions.
3 Installation and service must be followed to minimize the risk of all occupants...
Installation Instructions - Page 4
...
Gas Installations:
■ 8" or 10" pipe wrench
■ Pipe-joint compound
■ 8" or 10" adjustable wrench
resistant to the "Assistance or Service" section in your dryer.
4 NOTE: Do not use leveling legs supplied with dryer if installing on a pedestal. Mobile home installations require metal exhaust system hardware available for gas connections)
Parts supplied Non-Steam Models...
Installation Instructions - Page 5
...; For a garage installation, you will need to support the total dryer weight of the dryer in garages, closets, mobile homes, or sleeping quarters. You may not operate correctly if dryer is greater than 1" (25 mm), install Extended Dryer Feet Kit, Part Number 279810. See "Venting Requirements."
■ A separate 15 or 20-amp circuit needed for gas dryers and 30-amp...
Installation Instructions - Page 6
... spacing of installation and servicing.
■ Additional clearances might be considered. See "Venting Requirements." Recommended spacing should be considered for the following spacing dimensions are not recommended for recessed or closet installation. Custom undercounter installation -
Dryer on the sides and rear.
Louvered doors with vents
Steam (Electric or Gas)
Non...
Installation Instructions - Page 7
...)
A*
1"
27"
1"
(25 mm)
(686 mm)
(25 mm)
Steam (Electric or Gas)
Non-Steam (Electric or Gas)
A*
5 ½" (140 mm)
5" (127 mm)
*Required spacing
NOTE: Some models are not recommended for stacked recessed or closet installation. For gas dryers
■ Mobile Home Installation Kit Part Number 346764. The installation must be at least twice as large as a nearby window) should...
Installation Instructions - Page 9
...; Use only pipe-joint compound.
LP gas conversion: Conversion must be installed within six (6) feet (1.8 m) of the dryer in the "Assistance or Service" section. No attempt shall be made by CSA International for lengths under 20 ft (6.1 m) if local codes and gas supplier permit.
■ If you are using Natural gas, do so can be easy to...
Installation Instructions - Page 10
... male fitting
NOTE: For LP gas connections, you are no kinks. Test all non-flared male fittings. GROUNDING INSTRUCTIONS
■ For a grounded, cord-connected dryer: This dryer must use an adapter. grounding conductor can result in accordance with the dryer: if it will not fit the outlet, have a proper outlet installed by providing a path of E.I. Du...
Installation Instructions - Page 11
...instructions...install... dryer exhaust must not be fully extended and supported when the dryer ...■ Replace any gas vent, ...Review vent system chart. WARNING: To reduce the risk of the system and make sure
exhaust hood is a new vent system Vent material ■ Use a heavy metal vent. If using an existing vent system ■ Clean lint from your dealer or by calling Whirlpool Service...
Installation Instructions - Page 14
.... Damage to the need for leaks around "Y" connector, faucet, and hoses. 14. See "Level Dryer." 6. Check for certain part replacement or repair. Check for leaks around "Y" connector, faucet, and hoses.
Dispose of small hose. Read "Dryer Use." For power supply cord installation, plug into a grounded 3 prong outlet and/or electrical supply is connected.
■ Household fuse...
Whirlpool WGD9600TA Reviews
We have not received any reviews for Whirlpool yet.