Whirlpool WED6400SB - Cabrio 7.0 Cu Ft Capacity Electric Dryer Support and Manuals
Get Help and Manuals for this Whirlpool item
View All Support Options Below
Free Whirlpool WED6400SB manuals!
Problems with Whirlpool WED6400SB?
Ask a Question
Free Whirlpool WED6400SB manuals!
Problems with Whirlpool WED6400SB?
Ask a Question
Most Recent Whirlpool WED6400SB Questions
Wiring To Heating Element
i unplugged heating element and ordered new one. I can't remember where the wires connect
i unplugged heating element and ordered new one. I can't remember where the wires connect
(Posted by Rkronenb 8 years ago)
Af Flashing On Estimated Time Remaining What Does It Mean?
(Posted by Anonymous-143053 9 years ago)
Cabrio Dryer Won't Start Sensing Light On
(Posted by Jikokai 10 years ago)
Wed6400sgo Cabrio Doesn't Heat
Is there a heating element? Is there a service manual and parts breakdown schematic available online...
Is there a heating element? Is there a service manual and parts breakdown schematic available online...
(Posted by lboyle14 10 years ago)
Popular Whirlpool WED6400SB Manual Pages
Use and Care Guide - Page 3
...Installation and service must be detected by UL or CSA.
WARNING: For your gas supplier from a neighbor's phone. Gas suppliers recommend that you smell gas" instructions.
3 If a gas leak is detected, follow the "What to do not use any electrical... manual must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Fuel Gas Code,...
Use and Care Guide - Page 5
... the desired drying
time is a guide to persons, read the IMPORTANT SAFETY INSTRUCTIONS before each cycle. 1. TIMED DRY - Your dryer may not have all of load, and adjust Dryness Level for optimal performance. Select AUTOMATIC or TIMED cycle. 5.
The following is displayed 4. Please refer to specific sections of fire, electric shock, or injury to using...
Use and Care Guide - Page 6
...Settings Charts. A sensor detects the moisture in the dryer too long.
The dryer will continue to handle and reduces wrinkling. Cool Down makes the loads easier to tumble with heat followed by pressing Dryness and choosing More, Normal, Less, or Damp. Follow package instructions... with heat.
Steam models
Non-Steam models
Automatic ..." section) for a guide to drying various loads....
Use and Care Guide - Page 8
....
Press END OF CYCLE SIGNAL until the dryer goes into the cycle.
Wet The Wet light illuminates at any time to turn on during the WRINKLE SHIELD™ setting. The Wet light illuminates until the desired volume (Loud, Soft, or Off) is not detected after cool down part of the cycle reduces wrinkling. Damp...
Use and Care Guide - Page 9
...to different installations, environmental conditions or personal preference. Press PAUSE/CANCEL twice.
2. Changing Modifiers and Options after pressing Start 1. Press START to save the drying setting.
5. Press and hold ) START button (about 1 second).
9 The drying setting you purchased your Auto Dry cycles.
Dryer back panel
3.
The last selection will affect all of the manual or...
Use and Care Guide - Page 11
... inlet hoses and hose screen after 5 years of use dryer again
1. Reinstalling the dryer
Follow the "Installation Instructions" to faucet. Plug in death or electrical shock.
1. Flush water pipes. Turn on vacation or not using your dryer. Open the dryer door. Replace all parts and panels before servicing. Steam models only: Disconnect the water inlet hose from faucet and drain.
This...
Use and Care Guide - Page 12
... on .
Electric dryers use ? Refer to "Electrical Connection" in the Installation Instructions for details.
Confirm the exterior vent exhaust hood is the dryer level front to back and side to side? Refer to "Plan Vent System" in the Installation Instructions for details.
Large loads may require pressing and holding the Start button for service.
■ "L2" Diagnostic Code (low...
Use and Care Guide - Page 15
... calling
Whirlpool. Service calls to the appliance.
8. If you on the duration of implied warranties of your major appliance, to replace or repair house fuses, or to resolve the
problem after checking "Troubleshooting," additional help you obtain assistance or service if you need to published user or operator instructions and/or installation instructions.
2. Repairs to parts or...
Installation Instructions - Page 1
... and Parts 2 Optional Equipment 2 Location Requirements 3
ELECTRIC DRYER POWER HOOKUP 4 Electrical Requirements 4 Electrical Connection 5
VENTING 10 Venting Requirements 10 Plan Vent System 11 Install Vent System 12
INSTALL LEVELING LEGS 12 CONNECT VENT 12 CONNECT INLET HOSE (STEAM MODELS 13 LEVEL DRYER 13 COMPLETE INSTALLATION 13
Reverse Door Swing 14 TROUBLESHOOTING 15
Dryer...
Installation Instructions - Page 2
... driver (recommended)
■ Tape measure
■ Pliers
4 Leveling legs
A
B
A. NOTE: Do not use leveling legs supplied with dryer if installing on a pedestal. Parts needed
Check local codes. For further information, please refer to your dryer.
2 See "Electrical Requirements" and "Venting Requirements" before starting installation. Optional Equipment
Refer to the "Assistance or Service...
Installation Instructions - Page 3
... nearby window) should be exposed to support total dryer weight of 1" (25 mm) under entire dryer. Cold water supply may not shut off at temperatures below 45ºF (7ºC). Check code requirements. See "Venting Requirements." Installation must conform to open fully. Openings (such as dryer exhaust opening.
3
NOTE: Most installations require minimum 5" (127 mm) clearance for...
Installation Instructions - Page 10
...install flexible metal vent in your dealer or by calling Whirlpool Service. Do not use plastic or metal foil vent. ■ 4" (102 mm) heavy metal exhaust vent and clamps must be
used for cleaning.
■ Flexible metal vent must not be fully extended and supported when the dryer is not plugged with lint.
■ Replace... heavy metal vent.
■ Review vent system chart. Box hood style...
Installation Instructions - Page 11
... necessary to the manufacturer's instructions. Refer to connect elbows H.
Please see the "Assistance or Service" section in :
Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc. If you prefer, you may result in your installation.
Exhaust hood
H
E. Exhaust outlet
Optional exhaust installations
A
B
C
A. all models
This dryer can cause moisture and lint...
Installation Instructions - Page 13
... hoses.
If there is not level, prop up or down and check again for certain part replacement or repair.
13 For power supply cord installation, plug into a grounded outlet. NOTE: Do not overtighten. Damage to adjust the legs up the dryer using a wood block.
A
A. Inlet to fill valve at bottom of long hose to cold...
Installation Instructions - Page 14
... turning on the door. Cosmetic screw
A
3. Install 4 plastic plugs into an outlet and/or electrical supply
is connected. ■ Household fuse is intact and tight, or circuit breaker has
not tripped. ■ Dryer door is closed.
Reverse the strike 1.
This odor is common when the heating element is first heated. NOTE: Door strike and plugs must be a problem...
Whirlpool WED6400SB Reviews
We have not received any reviews for Whirlpool yet.