XE-A506 Operation Manual in English and Spanish
Page 5
... (Void mode 68 HOW TO USE AN SD MEMORY CARD...69 1 What You Can Do with an SD Memory Card 69 2 In Case of SD Error...70 3 Inserting and Removing an SD Memory Card 71 4 Formatting an SD Memory Card ...71 5 Saving and Restoring All the Data ...72 6 Writing...Paper 74 4 Replacing the Paper Roll ...75 5 Removing a Paper Jam ...77 6 Cleaning the Print Head...77 7 Removing the Till and the Drawer...78 8 Opening the Drawer by Hand ...78 9 Before Calling for Service ...79 Error message table ...79 SPECIFICATIONS ...80 MANUAL DE INSTRUCCIONES (VERSION EN ESPAÑOL) 3 Amount for ......
... (Void mode 68 HOW TO USE AN SD MEMORY CARD...69 1 What You Can Do with an SD Memory Card 69 2 In Case of SD Error...70 3 Inserting and Removing an SD Memory Card 71 4 Formatting an SD Memory Card ...71 5 Saving and Restoring All the Data ...72 6 Writing...Paper 74 4 Replacing the Paper Roll ...75 5 Removing a Paper Jam ...77 6 Cleaning the Print Head...77 7 Removing the Till and the Drawer...78 8 Opening the Drawer by Hand ...78 9 Before Calling for Service ...79 Error message table ...79 SPECIFICATIONS ...80 MANUAL DE INSTRUCCIONES (VERSION EN ESPAÑOL) 3 Amount for ......
XE-A506 Operation Manual in English and Spanish
Page 11
...to the printing position as illustrated above . 2. Remove the white retainer at the position shown at the right. Move the print head release lever to the procedure shown below with the register. To charge the batteries, set the mode switch to clear message after ... position other than "OFF" with the power cord plugged into the AC outlet. Retainer Print head release lever (printing position) 5 Installing paper rolls Precaution: The paper cutter is operated by mistake, an error message such as illustrated above . 9 The register can print receipts and journals. Set a ...
...to the printing position as illustrated above . 2. Remove the white retainer at the position shown at the right. Move the print head release lever to the procedure shown below with the register. To charge the batteries, set the mode switch to clear message after ... position other than "OFF" with the power cord plugged into the AC outlet. Retainer Print head release lever (printing position) 5 Installing paper rolls Precaution: The paper cutter is operated by mistake, an error message such as illustrated above . 9 The register can print receipts and journals. Set a ...
XE-A506 Operation Manual in English and Spanish
Page 76
...(a permanent magnet and electromagnet are ready to section 4 in this machine.) • Use the print head release lever only when necessary. • Never pull the paper when it . • Avoid heat....returns to normal operation after power recovery. (See the sample print.) 2 In Case of Printer Error If the printer runs out of high humidity and temperature, exposure to direct sunlight, contact with ...glue, thinner or a freshly copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until you want to the correct position, then...
...(a permanent magnet and electromagnet are ready to section 4 in this machine.) • Use the print head release lever only when necessary. • Never pull the paper when it . • Avoid heat....returns to normal operation after power recovery. (See the sample print.) 2 In Case of Printer Error If the printer runs out of high humidity and temperature, exposure to direct sunlight, contact with ...glue, thinner or a freshly copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until you want to the correct position, then...
XE-A506 Operation Manual in English and Spanish
Page 81
...GETTING STARTED"? (Note that do not necessarily indicate functional faults of the connector loosened? Error message Error status Action ENTRY ERROR MISOPERATION NO RECORD MEMORY FULL SBTL COMPUL. INH. OPEN PR INH. Print head release lever is unusual. (7) A barcode cannot be scanned. Make a correct key ...(6) Printing is lifted up spool (to the printing position). TEND COMPUL. UNIT PR NOT NON-TEND BUFFER FULL HEAD UP PAPER EMPTY Registration error Misoperation error Undefined code is not allowed. Install a receipt and/or journal paper. 79 9 Before Calling for Service The...
...GETTING STARTED"? (Note that do not necessarily indicate functional faults of the connector loosened? Error message Error status Action ENTRY ERROR MISOPERATION NO RECORD MEMORY FULL SBTL COMPUL. INH. OPEN PR INH. Print head release lever is unusual. (7) A barcode cannot be scanned. Make a correct key ...(6) Printing is lifted up spool (to the printing position). TEND COMPUL. UNIT PR NOT NON-TEND BUFFER FULL HEAD UP PAPER EMPTY Registration error Misoperation error Undefined code is not allowed. Install a receipt and/or journal paper. 79 9 Before Calling for Service The...
Quick Start Guide
Page 1
...than "OFF". Push the printer cover forward and detach it to take -up excess slack in the paper. 9. Retainer Print head release lever 1. If the printer does not catch the paper, feed the paper while pressing } as illustrated right. Cut ... paper roll in step 2. 6. Set a paper roll in the paper cradle of the journal side as illustrated right. XE-A506 Quick Start Guide The following procedure: 1. Make sure the paper end is not inserted into the slit in the take up... revolution of the cash register when you press a key by mistake, an error message may be displayed.
...than "OFF". Push the printer cover forward and detach it to take -up excess slack in the paper. 9. Retainer Print head release lever 1. If the printer does not catch the paper, feed the paper while pressing } as illustrated right. Cut ... paper roll in step 2. 6. Set a paper roll in the paper cradle of the journal side as illustrated right. XE-A506 Quick Start Guide The following procedure: 1. Make sure the paper end is not inserted into the slit in the take up... revolution of the cash register when you press a key by mistake, an error message may be displayed.