XE-A506 Operation Manual in English and Spanish
Page 5
...Logo message print format ...57 High amount lockout (HALO) for cash in drawer (CID) (sentinel 57 Online time out setting ...57 Thermal printer density ...58 Language selection...58 Training clerk specification for training mode 58 AUTO key programming ...59 4 Reading Stored Programs ...59 TRAINING... In Case of Power Failure ...74 2 In Case of Printer Error ...74 3 Cautions in Handling the Printer and Recording Paper 74 4 Replacing the Paper Roll ...75 5 Removing a Paper Jam ...77 6 Cleaning the Print Head...77 7 Removing the Till and the Drawer...78 8 Opening the Drawer by Hand...
...Logo message print format ...57 High amount lockout (HALO) for cash in drawer (CID) (sentinel 57 Online time out setting ...57 Thermal printer density ...58 Language selection...58 Training clerk specification for training mode 58 AUTO key programming ...59 4 Reading Stored Programs ...59 TRAINING... In Case of Power Failure ...74 2 In Case of Printer Error ...74 3 Cautions in Handling the Printer and Recording Paper 74 4 Replacing the Paper Roll ...75 5 Removing a Paper Jam ...77 6 Cleaning the Print Head...77 7 Removing the Till and the Drawer...78 8 Opening the Drawer by Hand...
XE-A506 Operation Manual in English and Spanish
Page 7
... is a receipt/journal dual station type thermal printer, and therefore it does not require any type of the printer. If the paper becomes jammed and you need to move the head.... Be careful not to register data. MGR: For manager's entries. Lift the rear of the jammed paper. This key can pull the lever even further toward you can be lifted by inserting supplied mode key ...lever The print head can be used to remove. Pulling the lever forward lifts up spool Paper roll cradle Paper chute Print head release lever The printer is mounted on the printer (receipt side). It ...
... is a receipt/journal dual station type thermal printer, and therefore it does not require any type of the printer. If the paper becomes jammed and you need to move the head.... Be careful not to register data. MGR: For manager's entries. Lift the rear of the jammed paper. This key can pull the lever even further toward you can be lifted by inserting supplied mode key ...lever The print head can be used to remove. Pulling the lever forward lifts up spool Paper roll cradle Paper chute Print head release lever The printer is mounted on the printer (receipt side). It ...
XE-A506 Operation Manual in English and Spanish
Page 76
...you are not going to use it is in contact with glue, thinner or a freshly copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until you are used in this chapter, install a new roll, then press the key. Avoid direct sunlight. • The...head is set apart from scratching or other means. • Be very careful when handling the thermal paper. The paper will appear on the display. Cautions in handling the recording paper (thermal paper) • Use only paper specified by friction from the plate. (head-up position) Printing position Head-up , the ...
...you are not going to use it is in contact with glue, thinner or a freshly copied blueprint, and heat caused by SHARP. • Do not unpack the thermal paper until you are used in this chapter, install a new roll, then press the key. Avoid direct sunlight. • The...head is set apart from scratching or other means. • Be very careful when handling the thermal paper. The paper will appear on the display. Cautions in handling the recording paper (thermal paper) • Use only paper specified by friction from the plate. (head-up position) Printing position Head-up , the ...
XE-A506 Operation Manual in English and Spanish
Page 77
... remove the take-up spool. 5. outside diameter: 3.18 in (81 mm) Quality: Thermal paper • Be sure to set the paper roll) (How to cut 1. Therefore, when setting a new paper roll in the machine, be sure to cut off approximately one . If you plan on not using your ...the paper roll is out of the way. 4. 4 Replacing the Paper Roll Be sure to use of any other paper rolls other than those specified could cause paper jamming, resulting in register malfunction. Remove the paper roll from the paper roll cradle of the journal side. The use paper rolls specified by SHARP.
... remove the take-up spool. 5. outside diameter: 3.18 in (81 mm) Quality: Thermal paper • Be sure to set the paper roll) (How to cut 1. Therefore, when setting a new paper roll in the machine, be sure to cut off approximately one . If you plan on not using your ...the paper roll is out of the way. 4. 4 Replacing the Paper Roll Be sure to use of any other paper rolls other than those specified could cause paper jamming, resulting in register malfunction. Remove the paper roll from the paper roll cradle of the journal side. The use paper rolls specified by SHARP.
XE-A506 Operation Manual in English and Spanish
Page 82
...///) for the connection with the XE-A506. SPECIFICATIONS Model: XE-A506 Dimensions: 16.5 (W) x 16.9 (D) x 11.9 (H) in. (420 (W) x 430 (D) x 302 (H) mm) Weight: 27.5 Ib (12.5 kg) Power source: 120V AC ± 10%, 60 Hz Power consumption: Stand-by SHARP Co. diam.: 3.18 in ...2 lines) Customer display: 7-segment display (7 positions) Printer: Type: 2-station thermal printer Printing speed: Approx. 13.3 lines/second Printing capacity: 24 digits each for receipt and journal paper Other functions: • Graphic logo printing function • Logo message function ...
...///) for the connection with the XE-A506. SPECIFICATIONS Model: XE-A506 Dimensions: 16.5 (W) x 16.9 (D) x 11.9 (H) in. (420 (W) x 430 (D) x 302 (H) mm) Weight: 27.5 Ib (12.5 kg) Power source: 120V AC ± 10%, 60 Hz Power consumption: Stand-by SHARP Co. diam.: 3.18 in ...2 lines) Customer display: 7-segment display (7 positions) Printer: Type: 2-station thermal printer Printing speed: Approx. 13.3 lines/second Printing capacity: 24 digits each for receipt and journal paper Other functions: • Graphic logo printing function • Logo message function ...