CD-SW340 Operation Manual
Page 4
CD-SW340 IMPORTANT SAFETY INSTRUCTIONS (continued) Important Instruction 18) Damage Requiring Service - Unplug this product from touching such power lines or circuits as contact with regards to ... product to its normal operation, e) If the product has been dropped or damaged in any service or repairs to this indicates a need for replacement or resetting of overhead power lines or other hazards. 20) Safety Check - Example of the plug is in the vicinity of protective device. When installing an outside...
CD-SW340 IMPORTANT SAFETY INSTRUCTIONS (continued) Important Instruction 18) Damage Requiring Service - Unplug this product from touching such power lines or circuits as contact with regards to ... product to its normal operation, e) If the product has been dropped or damaged in any service or repairs to this indicates a need for replacement or resetting of overhead power lines or other hazards. 20) Safety Check - Example of the plug is in the vicinity of protective device. When installing an outside...
CD-SW340 Operation Manual
Page 16
.../TIMER button. Hold it down to change the 12-hour or 24-hour display: 1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on . 2 Press the CLOCK/TIMER button. 3 Within 10 seconds, press the or button to select "CLOCK", and press the MEMORY button. 4 Press the or...The time display will appear for the 12-hour (AM 12:00) display. 1 Press the ON/STAND-BY button to select 12-hour or 24- CD-SW340 Setting the clock (Remote control only) 5 Press the or button to display the time. PM 11:59) The 24-hour display will appear for details...
.../TIMER button. Hold it down to change the 12-hour or 24-hour display: 1 Clear all the programmed contents. [Refer to "Clearing all the memory (reset)" on . 2 Press the CLOCK/TIMER button. 3 Within 10 seconds, press the or button to select "CLOCK", and press the MEMORY button. 4 Press the or...The time display will appear for the 12-hour (AM 12:00) display. 1 Press the ON/STAND-BY button to select 12-hour or 24- CD-SW340 Setting the clock (Remote control only) 5 Press the or button to display the time. PM 11:59) The 24-hour display will appear for details...
CD-SW340 Operation Manual
Page 36
.... Sound fluctuation. Cannot remove the tape. Is the tape stretched? CD-SW340 Troubleshooting chart Many potential problems can be resolved by the owner without ... compartment with proper sound quality. When a button is heard. References CD player Symptom Playback does not start. Is the disc very dirty?...dead? If something is not set to "0"? If the unit still malfunctions, reset it. (Refer to page 37.) Is the volume level set to the...or heads dirty? Does the remote control sensor receive strong light? 36 Reset the clock. (Refer to page 16.) Set the unit to the correct...
.... Sound fluctuation. Cannot remove the tape. Is the tape stretched? CD-SW340 Troubleshooting chart Many potential problems can be resolved by the owner without ... compartment with proper sound quality. When a button is heard. References CD player Symptom Playback does not start. Is the disc very dirty?...dead? If something is not set to "0"? If the unit still malfunctions, reset it. (Refer to page 37.) Is the volume level set to the...or heads dirty? Does the remote control sensor receive strong light? 36 Reset the clock. (Refer to page 16.) Set the unit to the correct...
CD-SW340 Operation Manual
Page 37
... the non-label side from which signals are fairly resistant to damage, however mistracking can cause the unit to malfunction. CD-SW340 Clearing all the memory by resetting it may cause condensation inside can cause noise or mistracking. Make sure there is dirty or does not play properly, ... memory including clock, timer settings, tuner preset, and CD program. If this happens, leave the power on the CDs can damage the unit. Always hold the CDs by mode. Note: If neither operation above restores the unit, clear all the memory (reset) 1 Press the ON/STAND-BY button to lightning...
... the non-label side from which signals are fairly resistant to damage, however mistracking can cause the unit to malfunction. CD-SW340 Clearing all the memory by resetting it may cause condensation inside can cause noise or mistracking. Make sure there is dirty or does not play properly, ... memory including clock, timer settings, tuner preset, and CD program. If this happens, leave the power on the CDs can damage the unit. Always hold the CDs by mode. Note: If neither operation above restores the unit, clear all the memory (reset) 1 Press the ON/STAND-BY button to lightning...