SanDisk SDCFB-64-A10 - CompactFlash 64 MB Support and Manuals
Get Help and Manuals for this SanDisk item
View All Support Options Below
Free SanDisk SDCFB-64-A10 manuals!
Problems with SanDisk SDCFB-64-A10?
Ask a Question
Free SanDisk SDCFB-64-A10 manuals!
Problems with SanDisk SDCFB-64-A10?
Ask a Question
Popular SanDisk SDCFB-64-A10 Manual Pages
Product Manual - Page 28
...
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width
Symbol Vi (CE)
TSU (VCC) TSU (RESET) TREC (VCC)
tpr tpf TW (RESET) Th (Hi-z Reset) TS (Hi-z Reset)
Condition 0V Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in...
Product Manual - Page 35
...The minimum cycle time supported by the associated mode (e.g., a device supporting PIO Mode 4 ...SanDisk CompactFlash Card OEM Product Manual
Interface Description
Table 3-14 contains the specification information related to the I /O Write Timing Specification
Item Data Setup before -IOWR Data Hold following -IOWR -IOWR Width Time Address Setup before -IOWR Address Hold following -IOWR -CE Setup...
Product Manual - Page 36
... 10 20 5 30 10
a.
data tri-state (max.)
t9
IORD-/IOWR-
Interface Description
SanDisk CompactFlash Card OEM Product Manual
Figure 3-7 Register Transfer to or greater than the sum of t0, t2, and t2i shall... device imple mentation shall support any legal host implementation. pulse width 8-bit (min.)
t2i a
IORD-/IOWR- data setup (min.)
t6
IORD- recovery time (min.)
t3
IOWR-
Product Manual - Page 38
...support any legal host implementation. pulse width 16-bit (min.) t2ia IORD-/IOWR-
The minimum total cycle time requirements are located in the system.
02/07, Rev. 12.0
3-20
© 2007 SanDisk Corporation setup... IDENTIFY DEVICE data.
Interface Description
SanDisk CompactFlash Card OEM Product Manual
The PIO data transfer parameters are identified by appropriate information in the...
Product Manual - Page 42
...SanDisk CompactFlash Card OEM Product Manual
Card Configuration and Status Register (con't)
Bit
Name
Description
D7
Changed Indicates that caused the interrupt request has been
serviced. The PCMCIA Rdy/-Bsy value becomes BUSY when this bit is a "0".
3.4.4
Pin Replacement... CRdy/-Bsy.
When the bit is changed. If interrupts are set to zero "0" and pin 46 (-STSCHG) signal will not ...
Product Manual - Page 47
...
A9-REG A10 A4 A3 A2 A1 A0 Offset
-OE=0
-WE=0
1
0
X
0 0 0
0
0
Even RD Dataa
Even WR Dataa
1
0
X
0 0 0
1
1
Error Registerb
Featuresb
...register 9 are not supported. This 1 KByte memory...SanDisk CompactFlash Card OEM Product Manual
ATA Register Set...instruction.
c.
Some hosts, such as shown in Table 4-4. Note that the address space of the registers at off set...
Product Manual - Page 49
...]; D5
0
Bit set to be found. Offset 3)
This register contains the starting sector number or bits 7-0 of a card status condition:
(Not Ready, Write Fault, etc.) or when an invalid command has been
issued. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2-
Product Manual - Page 51
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status Registers (Address-1F7[177]&3F6[376]; ... locked out from
the host through the Data Register. D0
ERR
Set when the previous command has ended in the Error Register contain additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376]; This bit is...
Product Manual - Page 59
.../Write Long Commands Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) Big Endian Byte Order in the Identify Device Information. The parameter words in the buffer have the arrangement and meanings defined in Table 5-8. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description...
Product Manual - Page 64
...
Indication
0
0
SMART feature set not supported
1
1
Security Mode feature set supported
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not supported
5
1
Write cache supported
6
1
Look-ahead supported
7
0
Release Interrupt not supported
8
0
Service Interrupt not supported
9
0
Device Reset command...
Product Manual - Page 65
... and Write DMA Queued commands not supported by CF
Card
2
1
CFA feature set supported by CF Card
3
1
Advanced Power Management feature set by Set Features command
4
0
Removable Media Status feature set not supported by CF Card
15
--- SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Bits 0-13 of word 87 will be set to one and bit 15 of...
Product Manual - Page 70
... Read Multiple command.
Interrupts are transferred only if the error was a correctable data error. If the Read Multiple command is programmed by the Set Multiple Mode command, which contains the number of blocks or the block count) requested.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read Multiple-C4H
The Read Multiple command...
Product Manual - Page 73
... Spare sectors exhausted Data transfer error/aborted command Corrupted media format Write/erase failed
5.1.17
Seek-7XH
This command is effectively a NOP command to the card although it does perform a range check of range. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory...
Product Manual - Page 74
... data transfer Enable Write Cache Set Transfer Mode based on value and Sector Count register. The 9AH feature is unique to enable and clear 8-bit data transfer mode.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is issued, all features that are not part of defaults at Soft...
Product Manual - Page 106
... following information: product model number and description, serial numbers, nature of defect, conditions of use in the same way as new products.
RECEIVING WARRANTY SERVICE
According to do not meet or exceed the same published specifications as new products, provided such cards meet the original product's specifications. V. Please contact SanDisk's OEM Support Department at its...
SanDisk SDCFB-64-A10 Reviews
We have not received any reviews for SanDisk yet.