SanDisk SDCFB-2048-A10 - 2GB Compactflash Card Type I Retail Package Support and Manuals
Get Help and Manuals for this SanDisk item
This item is in your list!
View All Support Options Below
Free SanDisk SDCFB-2048-A10 manuals!
Problems with SanDisk SDCFB-2048-A10?
Ask a Question
Free SanDisk SDCFB-2048-A10 manuals!
Problems with SanDisk SDCFB-2048-A10?
Ask a Question
Popular SanDisk SDCFB-2048-A10 Manual Pages
Product Manual - Page 10
... soft error rate specification is analogous to the card. Advanced features of dynamic and static wear-leveling, and automatic block management are used to complete. The host software then waits for the command to ensure high data reliability and maximize flash life expectancy.
1.7.4
Using Erase Sector and Write Commands
SanDisk CompactFlash Memory cards support the...
Product Manual - Page 29
...Add Changea Address Setup Time
Symbol tc ...SanDisk CompactFlash Card OEM Product Manual
Interface Description
Figure 3-2 Power Up/Power Down Timing for all types of memory. trec
VIH
2V
3.3.4
Common Memory Read Timing Table 3-10 contains common memory read timing specifications for Systems not supporting RESET
tpr
VCC Min.
Table 3-10 Common Memory Read Timing Specification
Speed...
Product Manual - Page 35
SanDisk CompactFlash Card OEM Product Manual
Interface Description
Table 3-14 contains the specification information related to the minimum cycle time .../O Write Timing Diagram.
The minimum cycle time supported by devices in PIO Mode 3, 4 and Multiword DMA Mode 1, 2 respectively will not report a value less than or equal to the I /O Write Timing Specification
Item Data Setup before ...
Product Manual - Page 36
...and t2i shall be met. A device imple mentation shall support any legal host implementation. data hold (min.)
t6z b
IORD...sum of t2 and t2i. Interface Description
SanDisk CompactFlash Card OEM Product Manual
Figure 3-7 Register Transfer to/from Device
PIO...than the value reported in the devices IDENTIFY DEVICE data. data setup (min.)
t4
IOWR- b. This means a host implementation may...
Product Manual - Page 47
... as byte register with CE1 high and CE2 low accesses the error (read) or feature (write) register. This 1 KByte memory window to the data register is the odd byte of the registers at off set 1. Table 4-4 Memory Mapped Decoding
A9-REG A10 A4 A3 A2 A1 A0 Offset
-OE=0
-WE=0
1
0
X
0 0 0
0
0
Even RD Dataa...
Product Manual - Page 49
... indicated in this register is also accessed on data bits D15-D8 during a write operation to 0.
CE1- SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2- Offset 1, 0Dh Write Only)
This register provides information about the source of the Logical Block Address (LBA...
Product Manual - Page 51
... at power-up and remains cleared until card is ready.
D0
ERR
Set when the previous command has ended in the Error Register contain additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376];
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status & Alternate Status Registers (Address-1F7[177]&3F6[376...
Product Manual - Page 59
... are "0". of Sectors on Read/Write Long Commands Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model number in ASCII (left justified) ...Read/Write Multiple command Double-word not supported Capabilities: DMA Supported (bit 8), LBA supported (bit 9) Reserved
© 2007 SanDisk Corporation
5-5
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
ATA...
Product Manual - Page 64
... indicated. Obsolete
12
1
Write Buffer command supported by CF Card
13
1
Read Buffer command supported by CF Card
14
1
NOP command supported by the host as meaning that the features and command sets supported words are reserved.
02/07, Rev. 12.0
5-10
© 2007 SanDisk Corporation ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
Word 68: Minimum PIO...
Product Manual - Page 65
... by CF Card
1
0
Read DMA Queued and Write DMA Queued commands not supported by CF
Card
2
1
CFA feature set supported by CF Card
3
1
Advanced Power Management feature set by Set Features command
4
0
Removable Media Status feature set not supported
11
--- The older modes are reserved. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Bits 0-13 of Advanced PIO...
Product Manual - Page 70
...errors cause the command to the Read Sectors operation except that contained the error.
02/07, Rev. 12.0
5-16
© 2007 SanDisk Corporation ATA Command Description
SanDisk CompactFlash Card OEM Product Manual...block.
Interrupts are transferred only if the error was a correctable data error. DRQ qualification of the transfer is still set at the start of each sector.
...
Product Manual - Page 73
... ECC error Corrected ECC error Self test or diagnostic failed ID not found Spare sectors exhausted Data transfer error/aborted command Corrupted media format Write/erase ...error if the address is returned to the card following the command that returned an error.
SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes...
Product Manual - Page 74
... Disable Power on Reset (POR) establishment of the ATA Specification. Table 5-26 Set Features
Bit
7
6
5
4
3
2
1
0
Command...Write Cache Set Transfer Mode based on the CF Memory Card. If the 01H feature command is issued, all features that are used by the host to establish or select certain features. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set...
Product Manual - Page 105
... is found to SanDisk for each defective product was submitted and is returned to be incorporated in accordance with appropriate redundancy, fault tolerant or back-up features.
The defective product is on file at its products to operate without failure. C. If not, a warranty registration card must accompany each product's original retail package. II.
Product Manual - Page 106
... OR EXCLUSIONS MAY NOT APPLY TO YOU.
RECEIVING WARRANTY SERVICE
According to SanDisk's warranty procedure, defective product should be returned. V. Limited Warranty
SanDisk CompactFlash Card OEM Product Manual
All failing products returned to SanDisk under the provisions of failure is under different specifications and product designations if such products do so. Upon confirmation...
SanDisk SDCFB-2048-A10 Reviews
Do you have an experience with the SanDisk SDCFB-2048-A10 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for SanDisk yet.
Earn 750 points for your review!