SanDisk SDCFB-128-A10 - CompactFlash 128 MB Support and Manuals
Get Help and Manuals for this SanDisk item
View All Support Options Below
Free SanDisk SDCFB-128-A10 manuals!
Problems with SanDisk SDCFB-128-A10?
Ask a Question
Free SanDisk SDCFB-128-A10 manuals!
Problems with SanDisk SDCFB-128-A10?
Ask a Question
Popular SanDisk SDCFB-128-A10 Manual Pages
Product Manual - Page 3
... life or injury. and foreign patents
awarded and pending. Document 20-10-00038 Rev. 12.0
Revision History
Date February 2007
Revision 12.0
Description
Merged CFlash 11.2 manual with CFA Spec v4.0.
© 2007 SanDisk Corporation
i
Rev. 12.0, 02/07 SanDisk CompactFlash Card OEM Product Manual
SanDisk® Corporation general policy does not recommend the use only and is...
Product Manual - Page 28
... Levela
CE Setup Time CE Setup Time CE Recover Time VCC Rising Timeb VCC Falling Timeb Reset Width
Symbol Vi (CE)
TSU (VCC) TSU (RESET) TREC (VCC)
tpr tpf TW (RESET) Th (Hi-z Reset) TS (Hi-z Reset)
Condition 0V Interface Description
SanDisk CompactFlash Card OEM Product Manual
3.3.3
Power Up/Power Down Timing
The timing specification in...
Product Manual - Page 29
... driver/receiver to the card must be accounted for Systems not supporting RESET
tpr
VCC Min.
SanDisk CompactFlash Card OEM Product Manual
Interface Description
Figure 3-2 Power Up/Power Down Timing for by pull-up resistor on card (if present)
tpf
VCC Min.
VIH
tSU(VCC)
2V
VCC -CE1, -CE2
Always Hi-z from Add Changea Address Setup...
Product Manual - Page 35
...the page relative to the asserted condi tion. SanDisk CompactFlash Card OEM Product Manual
Interface Description
Table 3-14 contains the specification information related to the I /O Write Timing Specification
Item Data Setup before -IOWR Data Hold following -IOWR -IOWR Width Time Address Setup before -IOWR Address Hold following -IOWR -CE Setup before -IOWR -CE Hold following -IOWR -REG...
Product Manual - Page 36
... of /IORD to /from Device
PIO Timing Parameters
t0 a
Cycle time (min.)
t1
Address valid to IORD-/IOWR- setup (min.)
t2 a
IORD-/IOWR- data hold (min.)
t6z b
IORD- Interface Description
SanDisk CompactFlash Card OEM Product Manual
Figure 3-7 Register Transfer to the time that t0 is equal to address valid hold (min.)
Mode 4 (ns)
120...
Product Manual - Page 47
... to register 9 are not supported. Sector No.
1
0
...error (read) or feature (write) register. Byte accesses to the data register when the regis ter lies in memory space. Accesses to register 0, while register 9 accesses the odd byte. Therefore, if the regis ters are byte accessed in Table 4-4.
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set...instruction...
Product Manual - Page 49
...
issued. Offset 2)
This register contains the number of sectors of sectors that need to be found.
SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
Table 4-6 Data Register
Data Register Error/Feature Register Error/Feature Register
CE2- D2
ABRT
Set if the command has been aborted because of the Logical Block Address (LBA) for any...
Product Manual - Page 51
... additional information describing the error.
4.5.10 Device Control Register (Address-3F6[376]; The bits are defined as follows:
D7
D6
D5
D4
D3
D2
D1
BUSY
RDY
DWF
DSC
DRQ
CORR
0
D0 ERR
Bit
Name
Description
D7
BUSY
Set when the CompactFlash Card has access to a 1. SanDisk CompactFlash Card OEM Product Manual
ATA Register Set and Protocol
4.5.9
Status...
Product Manual - Page 59
...Firmware revision in ASCII (Rev M.ms) set by code Big Endian Byte Order in Word Model...
6
XXXXh
2
7-8
XXXXh
4
9
0000h
2
10-19
aaaa
20
20
0000h
2
21
0000h
2
22...not supported Capabilities: DMA Supported (bit 8), LBA supported (bit 9) Reserved
© 2007 SanDisk ...SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
5.1.5
Identify Device-ECH
The Identify Drive...
Product Manual - Page 64
...
SanDisk CompactFlash Card OEM Product Manual
Word 68: Minimum PIO Transfer Cycle Time With Flow Control. Table 5-9 Word 82 Description
Bit
Setting
Indication
0
0
SMART feature set not supported
1
1
Security Mode feature set supported
2
0
Removable Media feature set not supported
3
1
Power Management feature set supported
4
0
Packet Command feature set not supported...
Product Manual - Page 65
... these words should not be set not supported by Set Features command
4
0
Removable Media Status feature set to one and bit 15 of word 87 will be cleared to zero to provide indication that the features/command sets enabled words are valid. The older modes are reserved.
SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Bits 0-13...
Product Manual - Page 70
... Number Register. The transfer begins at the sector where the error occurred. The flawed data is set and the data transfer will take place as possible are not...execution is identical to the Read Sectors command. ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.11
Read Multiple-C4H
The Read Multiple command performs similarly to the Read Sectors operation...
Product Manual - Page 73
...
5.1.17
Seek-7XH
This command is effectively a NOP command to the card following the command that returned an error. SanDisk CompactFlash Card OEM Product Manual
ATA Command Description
Table 5-24 defines the valid extended error codes for the CompactFlash Memory Card Series product. This command must be the next command issued to the card although it does...
Product Manual - Page 74
... compatibility with the SDP Series but has no impact on value and Sector Count register.
ATA Command Description
SanDisk CompactFlash Card OEM Product Manual
5.1.18 Set Features-EFH
This command is issued, all features that are supported. If the 01H feature command is used to establish or select certain features. The 9AH feature is unique...
Product Manual - Page 106
...repairs. IV. V. SanDisk reserves the right to repair or replace, at its discretion, ship repaired or rebuilt products identified in other rights that vary from state to the unit resulting from SanDisk Corporation. This warranty gives you specific...TO YOU. Limited Warranty
SanDisk CompactFlash Card OEM Product Manual
All failing products returned to SanDisk under the provisions of ...
SanDisk SDCFB-128-A10 Reviews
We have not received any reviews for SanDisk yet.