Ridgid R4512 Support and Manuals
Get Help and Manuals for this Ridgid item
View All Support Options Below
Free Ridgid R4512 manuals!
Problems with Ridgid R4512?
Ask a Question
Free Ridgid R4512 manuals!
Problems with Ridgid R4512?
Ask a Question
Most Recent Ridgid R4512 Questions
Replacement Parts
In behind the motor end cap there is a fan that I need a new one and I was wondering if there is a p...
In behind the motor end cap there is a fan that I need a new one and I was wondering if there is a p...
(Posted by carhodenizer 2 years ago)
Why Did My Ridgid Table Saw Power Die After I Turned It On?
I turned on the power to my table saw and everything died. Tried turning the power switch on and off...
I turned on the power to my table saw and everything died. Tried turning the power switch on and off...
(Posted by georgegll628 2 years ago)
Ridgid R4512 Videos
Nickle test new ridgid R4512.
Duration: :14
Total Views: 109
Duration: :14
Total Views: 109
Ridgid R4512 Table Saw -- Stand Assembly
Duration: :43
Total Views: 12,375
Duration: :43
Total Views: 12,375
Ridgid R4512 Hybrid Table Saw
Duration: 10:06
Total Views: 98,605
Duration: 10:06
Total Views: 98,605
Ridgid R4512 table saw
Duration: 1:19
Total Views: 30,539
Duration: 1:19
Total Views: 30,539
Popular Ridgid R4512 Manual Pages
Owners Manual - Page 1
... operator's manual before using this product. When properly cared for, it will give you for dependability, ease of operation, and operator safety. WARNING:
To reduce the risk of rugged, trouble-free performance.
TABLE SAW
R4512
45
Your table saw has been engineered and manufactured to our high standards for buying a RIDGID® product. OPERATOR'S MANUAL
10 in. SAVE THIS MANUAL FOR...
Owners Manual - Page 4
... accessories listed in this manual or addendums. Use of the motor could ignite fumes.
Inspect TOOL CORDS periodically. Failure to whether the tool is properly grounded.
Use only correct electrical devices: 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that is moving parts during use only identical replacement parts. Keep the blade...
Owners Manual - Page 5
... only recommended accessories listed in this manual or addendums. Use of accessories that are specially designed to filter out microscopic particles.
5 To reduce your hands to support or guide the workpiece. b) Keeping rip fence parallel to the saw table for any reason.
MOVE THE RIP FENCE out of the way when cross cutting.
NEVER use to instruct other masonry...
Owners Manual - Page 7
... or serious injury. Call RIDGID® customer service for repair. We recommend Wide Vision Safety Mask for use only identical replacement parts. WARNING:
Indicates a potentially hazardous situation, which is marked to comply with ANSI Z87.1. Before beginning power tool operation, always wear safety goggles or safety glasses with side shields. SAVE THESE INSTRUCTIONS
7 Always use eye...
Owners Manual - Page 10
... tool is bent (or set) outward from a block so the end (or part of the workpiece pushed into the blade or being placed inadvertently in a non-through cut .
As it securely against the table or fence during cutting operations.
Leading End The end of the end) is being guided by the blade. Saw Blade Path The area over the...
Owners Manual - Page 12
... optional clamps and accessories. The easy-to -read indicator shows the exact angle for a cross cut , with the locking handle. carbidetooth blade. The miter gauge aligns the wood for a miter cut . The easy-to -read rip scale provides precise measurements for use blades rated less than the saw table, the table extensions give the operator additional support when cutting...
Owners Manual - Page 13
... rip fence is intended to turn the switch off ( O ) position before operating the switch to use by an insert called the throat plate. Fig. 6
13 It is not in contact with a power switch that has a built-in serious personal injury. TO lock your workpiece is very important to start the tool.
Detailed instructions are...
Owners Manual - Page 18
... stand is helpful to move the saw and set it upright.
Lift the saw table and motor housing from the box and position it on the boards as the power cord.
Do not tighten completely.
The larger holes in the extension should be aligned with the English WARNING label attached.
ASSEMBLY
INSTALLING THE TABLE EXTENSIONS
See Figures 10 - 11.
Owners Manual - Page 20
... by pressing them into the leg stand, aligning the holes
in the caster assembly with the hole in
the front of the cabinet. Raise saw carefully until it sits upright. To raise the saw .
INSTALLING RIP FENCE STORAGE BRACKETS
See Figure 18. Remove the pre-installed bolt and nut from the small fastener...
Owners Manual - Page 25
... the saw table.
Slide a hex head bolt into the middle groove in the front rail.
Insert the bolts through the holes in the switch assembly mounting plate.
... all assembled parts are flush and level.
If the table extensions, rip fence, and rails are not level, make sure the table extensions are level with the top.
If the table extensions and rails are...
Owners Manual - Page 29
... such as cross cutting,
ripping, mitering, beveling, and compound cutting Dado cuts with optional accessories Cabinet making and woodworking NOTE: This table saw is designed to cut Not following correct operating procedures Misusing the saw without the blade guard unless specifically instructed to do so could result in objects being made.
29 This helps...
Owners Manual - Page 37
... lock knob and the hand farthest from the blade should kickback occur.
WARNING:
Using the rip fence as a cutoff gauge when cross cutting will result in the illustrations below. OPERATION
MAKING CUTS
This table saw can cause serious personal injury.
Remove the rip fence. Set the blade to power source. Your local library has many...
Owners Manual - Page 38
...support the same height as the table surface behind the saw for the workpiece.
Position the rip fence the desired distance from the blade should be placed on . Let the blade ...installed and working properly to a complete stop before moving the
workpiece into the blade.
Once the blade has made , turn the saw off . BLADE
RIP FENCE
RIP CUT
Set the blade...
Owners Manual - Page 49
... the blade teeth. GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Make sure the throat plate is ...saw 's motor bearings have been packed at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in serious personal injury.
Do not use only identical RIDGID replacement parts. Use of the miter gauge. Protect the blade...
Owners Manual - Page 54
... information when you , please call or visit. Please record the serial number in . When ordering repair parts, always give the following information:
Model No. R4512
Serial No.
987000-988 4-4-11 (REV:03)
54 OPERATOR'S MANUAL
10 in the space provided below. TABLE SAW
R4512
Customer Service Information
For parts or service, contact your nearest RIDGID authorized service center.
Ridgid R4512 Reviews
We have not received any reviews for Ridgid yet.