Ridgid DP1550 Support and Manuals
Get Help and Manuals for this Ridgid item
View All Support Options Below
Free Ridgid DP1550 manuals!
Problems with Ridgid DP1550?
Ask a Question
Free Ridgid DP1550 manuals!
Problems with Ridgid DP1550?
Ask a Question
Most Recent Ridgid DP1550 Questions
No Power To Unit
my drill press is a workhorse but today when i went to switch it on it had no power. neither the lig...
my drill press is a workhorse but today when i went to switch it on it had no power. neither the lig...
(Posted by brecktender 1 year ago)
Ridgid DP1550 Videos
Ridgid DP1550 Drill Press Review.avi
Duration: :43
Total Views: 3,457
Duration: :43
Total Views: 3,457
Ridgid DP1550 Drill Press
Duration: :34
Total Views: 960
Duration: :34
Total Views: 960
Popular Ridgid DP1550 Manual Pages
Owners Manual - Page 1
... for dependability, ease of injury, the user must read and understand the operator's manual before using this product. WARNING:
To reduce the risk of operation, and operator safety. SAVE THIS MANUAL FOR FUTURE REFERENCE DRILL PRESS
DP15501
®
®
Your new drill press has been engineered and manufactured to our high standards for buying a RIDGID product. OPERATOR'S MANUAL
15 in.
Owners Manual - Page 2
... Safety Rules ...3 n Specific Safety Rules...4 n Symbols...5-6 n Electrical ...7 n Glossary of Terms ...8 n Features ...9-10 n Unpacking ...11 n Loose Parts...12 n Tools Needed...13 n Assembly ...13-17 n Operation ...18-21 n Adjustments...22-26 n Maintenance ...27 n Accessories ...28 n Troubleshooting ...29 n Warranty ...31 n Parts Ordering/Service ...32
INTRODUCTION
Your drill press has many...
Owners Manual - Page 4
...support lock handle is properly repaired or replaced. Some examples of the material and possible operator injury. Sharp bits minimize stalling.
SPECIFIC SAFETY RULES
n KEEP BITS CLEAN AND SHARP. that may cause misalignment of these instructions... IS INSTALLED PROPERLY.
n LOCK THE MOTOR SWITCH OFF WHEN LEAVING THE DRILL PRESS. Do not perform layout, assembly, or setup work in...
Owners Manual - Page 6
... Wide Vision Safety Mask for repair.
SAVE THESE INSTRUCTIONS
6
When servicing, use this product until you return the product to your eyes, which , if not avoided, may result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may use only identical replacement parts. Save this operator's manual and review frequently for continuing safe...
Owners Manual - Page 7
... installed ...service personnel if the grounding instructions are insufficient extension cord size and multiple tools operating from the cutting area and position the cord so that is powered by the letters WA on material, tools, or other objects during cutting. Repair or replace...drill press is 120 volts, 60 Hz, AC only (normal household current). POWER SUPPLY
Before operating your drill press...
Owners Manual - Page 8
... Also known as a guide for driving the spindle pulley by means of a belt.
Feed Handles Three handles attached to the quill which allows the operator to accommodate different size workpieces.
8
Responsible for rotating the spindle. GLOSSARY OF TERMS
Base Large rectangular plate that supports the work table and drill press head assembly.
Chip The...
Owners Manual - Page 10
... make you careless. RACK
Combines with your drill press, familiarize yourself with the handles. COLUMN SUPPORT
Supports column, guides rack, and provides mounting holes for column to provide easy elevation of table by children and others.
ON-OFF SWITCH
Has locking feature. Refer to the column.
HEAD LOCK SET SCREWS
Lock the head to section "Assembly...
Owners Manual - Page 11
... materials until the damaged or missing parts are obtained and are replaced.
Wipe all loose parts, and satisfactorily operated your drill press until the missing parts are installed correctly. Contact your drill press. If any parts are damaged or missing, do so could result in one box. UNPACKING
The Drill Press is a heavy drill press. n Remove the packing materials from packing...
Owners Manual - Page 16
n Push up on the chuck and spindle
with drill press. n Unlock table support lock and raise table so its about two inches below tip of the storage tray assembly. n Turn chuck sleeve clockwise and open end of dirt on table.
ASSEMBLY
TO INSTALL THE STORAGE TRAY
See Figure 10. n Place the storage tray assembly around...
Owners Manual - Page 17
...INSTALL THE LIGHT BULB
See Figure 13. n Replace the lens cover. n Insert precision round steel rod or straight drill bit
approximately 3 in. (76.2 mm) long into the socket inside the head. n Retighten table bevel lock. WARNING:
Failure to unplug drill press... necessary, loosen the set screw. SCREWS
COMBINATION SQUARE
LIGHT BULB
LENS
Fig. 13
®
TABLE BEVEL LOCK BOLT
SET SCREW
17
®...
Owners Manual - Page 21
... of injury from spinning work or tool breakage, always clamp workpiece and backup material securely to table before operating drill press with the hex box wrench (included).
To return table to original position: n Loosen set screw and bevel lock, tilt table back to desired angle by reading bevel scale. Loosen bevel lock bolt...
Owners Manual - Page 23
...drill press, disengaging the spring housing from the right side of the table and raise the table until it remains engaged with feed handles set...support of the chuck will allow the spring assembly to drop on the right side of the head
assembly as shown. Remove both hands to the floor, place a piece of the drill press... the left side of the drill press and install in the same position on ...
Owners Manual - Page 27
... the set screw with a hex wrench and the hex nut with hammer.
WARNING:
To ensure safety and reliability, all slide bars lightly every two months. MAINTENANCE
WARNING:
When servicing use only identical RIDGID
®
replacement parts. come in order to keep the vertical movement smooth and to prevent it from the drill press spindle. n Unplug the drill press. PULLEYS...
Owners Manual - Page 28
...not use .
ACCESSORIES
Use Only Accessories Designed For This Drill Press To Reduce the Risk of Serious Injury From Thrown Broken Parts Or Work Pieces n When cutting large diameter holes:
...part hole cutters as they can suddenly bend outward or break.
n Drum sanders must never be operated on this drill press at high speed. Use only one piece, cup-type, hole cutters.
n Do not install...
Owners Manual - Page 32
.... Be sure to the motor housing.
DRILL PRESS
DP15501
CUSTOMER SERVICE INFORMATION
For parts or service, contact your nearest RIDGID authorized service center. The model number of the authorized service center nearest you call 1-866-539-1710 or visit us online at www.ridgid.com. OPERATOR'S MANUAL
15 in the space provided below. DP15501
Serial No.
983000-391
3-04
32
Please...
Ridgid DP1550 Reviews
We have not received any reviews for Ridgid yet.