English Manual
Page 2
This product is a registered trademark of Reebok. Apply the decal in the location shown. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 7 PART IDENTIFICATION CHART 8 ASSEMBLY 9 HOW TO USE THE TREADMILL 19 HOW TO FOLD AND MOVE THE TREADMILL 28 MAINTENANCE AND TROUBLESHOOTING 29 EXERCISE GUIDELINES 32 PART LIST 34 EXPLODED DRAWING... or illegible, call the telephone number on the front cover of the warning decals. Note: The decals may not be shown at actual size. 305284 REEBOK is manufactured and distributed under license from...
This product is a registered trademark of Reebok. Apply the decal in the location shown. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 7 PART IDENTIFICATION CHART 8 ASSEMBLY 9 HOW TO USE THE TREADMILL 19 HOW TO FOLD AND MOVE THE TREADMILL 28 MAINTENANCE AND TROUBLESHOOTING 29 EXERCISE GUIDELINES 32 PART LIST 34 EXPLODED DRAWING... or illegible, call the telephone number on the front cover of the warning decals. Note: The decals may not be shown at actual size. 305284 REEBOK is manufactured and distributed under license from...
English Manual
Page 4
...Always unplug the power cord immediately after use . 24. Never remove the motor hood unless instructed to raise, lower, or move the treadmill until it is not in use , before performing the maintenance and adjustment procedures described in serious injury or death. vice representative only. ... You must be performed by an authorized service representative. DANGER: 28. Never leave the treadmill unattended while it is properly assembled. (See ASSEMBLY on page 9, and HOW TO FOLD AND MOVE THE TREADMILL on page 7 for the location of the power switch), and unplug the power cord ...
...Always unplug the power cord immediately after use . 24. Never remove the motor hood unless instructed to raise, lower, or move the treadmill until it is not in use , before performing the maintenance and adjustment procedures described in serious injury or death. vice representative only. ... You must be performed by an authorized service representative. DANGER: 28. Never leave the treadmill unattended while it is properly assembled. (See ASSEMBLY on page 9, and HOW TO FOLD AND MOVE THE TREADMILL on page 7 for the location of the power switch), and unplug the power cord ...
English Manual
Page 8
PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity used for assembly. Extra parts may be included. #10 Washer (100)-2 #10 Star Washer (5)-4 1/4" Star Washer (3)-2 5/16" Star Washer (11)-8 3/8" Star Washer (13)-6 #8 x 1/2" Silver Screw (10)-1 #8 x 1/2" Screw (1)-14 #8 x 3/4" ... the part, from the PART LIST near the end of this manual. The number in the hardware kit, check to identify small parts used for assembly. Note: If a part is not in parentheses below to see whether it is preattached.
PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity used for assembly. Extra parts may be included. #10 Washer (100)-2 #10 Star Washer (5)-4 1/4" Star Washer (3)-2 5/16" Star Washer (11)-8 3/8" Star Washer (13)-6 #8 x 1/2" Silver Screw (10)-1 #8 x 1/2" Screw (1)-14 #8 x 3/4" ... the part, from the PART LIST near the end of this manual. The number in the hardware kit, check to identify small parts used for assembly. Note: If a part is not in parentheses below to see whether it is preattached.
English Manual
Page 9
...is an oily substance on the exterior of this manual) and register your product. 9 ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • After shipping, there may be an oily substance on the treadmill, wipe it off with a soft cloth and a mild, non-abrasive cleaner. ...8226; Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To identify small parts, see page 8. • Assembly requires the following tools: the...
...is an oily substance on the exterior of this manual) and register your product. 9 ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • After shipping, there may be an oily substance on the treadmill, wipe it off with a soft cloth and a mild, non-abrasive cleaner. ...8226; Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To identify small parts, see page 8. • Assembly requires the following tools: the...
English Manual
Page 12
Make sure not to the Right Upright (90) with two 5/16" x 2 1/2" Screws (28) and two 5/16" Star Washers (11). Do not fully tighten the Screws yet. Then, remove and discard the two indicated screws (C). 28 11 C B 81 90 12 Slide the Left Base Cover onto the Left Upright 6 (89), and slide the Right Base Cover onto the Right Upright (90). 6. Identify the Left and Right Base Covers (82, 83). Do not press the Base Covers into place yet. 89 82 90 83 7. Identify the right handrail assembly (B). 7 Attach the right handrail assembly (B) to pinch the Upright Wire (81).
Make sure not to the Right Upright (90) with two 5/16" x 2 1/2" Screws (28) and two 5/16" Star Washers (11). Do not fully tighten the Screws yet. Then, remove and discard the two indicated screws (C). 28 11 C B 81 90 12 Slide the Left Base Cover onto the Left Upright 6 (89), and slide the Right Base Cover onto the Right Upright (90). 6. Identify the Left and Right Base Covers (82, 83). Do not press the Base Covers into place yet. 89 82 90 83 7. Identify the right handrail assembly (B). 7 Attach the right handrail assembly (B) to pinch the Upright Wire (81).
English Manual
Page 13
8. Attach the left handrail assembly (D) to the Console Base, remove them. Remove and discard the two indicated screws (E). If 9 there are ties securing the Pulse Crossbar (93) to the Left Upright (89) with two 5/16" x 2 1/2" Screws (28) 8 and two 5/16" Star Washers (11); Then, remove the Pulse Crossbar (93). 64 E Tie 93 Tie 13 do not fully tighten the Screws yet. Remove and discard the two indicated screws (C). 28 11 C D 89 9. Set the Console Base (64) face down on a soft surface to avoid scratching the Console Base.
8. Attach the left handrail assembly (D) to the Console Base, remove them. Remove and discard the two indicated screws (E). If 9 there are ties securing the Pulse Crossbar (93) to the Left Upright (89) with two 5/16" x 2 1/2" Screws (28) 8 and two 5/16" Star Washers (11); Then, remove the Pulse Crossbar (93). 64 E Tie 93 Tie 13 do not fully tighten the Screws yet. Remove and discard the two indicated screws (C). 28 11 C D 89 9. Set the Console Base (64) face down on a soft surface to avoid scratching the Console Base.
English Manual
Page 15
...MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. Make sure not to the console wire. W ith the help of a second person, hold the console assembly near the Handrails (86) (only one connector and try again. do not, turn one side is shown). Connect the ground wire from the Upright ...the brackets on the Handrails (86) with four 5/16" x 3/4" Screws (4) and four 5/16" Star Washers (11); 12. Then, remove the wire tie from the console assembly to the brackets on the Handrails (86). Insert the excess Upright Wire (81) into place. If they do not fully tighten the Screws yet. 13...
...MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. Make sure not to the console wire. W ith the help of a second person, hold the console assembly near the Handrails (86) (only one connector and try again. do not, turn one side is shown). Connect the ground wire from the Upright ...the brackets on the Handrails (86) with four 5/16" x 3/4" Screws (4) and four 5/16" Star Washers (11); 12. Then, remove the wire tie from the console assembly to the brackets on the Handrails (86). Insert the excess Upright Wire (81) into place. If they do not fully tighten the Screws yet. 13...
English Manual
Page 16
... Uprights (89, 90) with six #8 x 1/2" Screws (1); start all six Screws, and then tighten them. Rotate each Outside Upright Cover needs to the console assembly with two #8 x 3/4" Screws (2). Note: The top edge of each Outside Upright Cover at an angle as you set it against the console... assembly as indicated by the arrows, and then retighten the Screws. Do not overtighten the Screws. 15 Console Assembly 87 D 2 2 2 89 B 90 2 96 16 14. Attach the Pulse Crossbar (93) to be inserted...
... Uprights (89, 90) with six #8 x 1/2" Screws (1); start all six Screws, and then tighten them. Rotate each Outside Upright Cover needs to the console assembly with two #8 x 3/4" Screws (2). Note: The top edge of each Outside Upright Cover at an angle as you set it against the console... assembly as indicated by the arrows, and then retighten the Screws. Do not overtighten the Screws. 15 Console Assembly 87 D 2 2 2 89 B 90 2 96 16 14. Attach the Pulse Crossbar (93) to be inserted...
English Manual
Page 17
Repeat the steps above on the other side of the treadmill with a Handrail Plate (38) and a #10 Washer (100) into the Left Outside Upright Cover (87) and into the bottom of the left handrail assembly (D). Press the Left Inside Upright Cover (88) against the Left Outside Upright Cover (87) until they snap together...
Repeat the steps above on the other side of the treadmill with a Handrail Plate (38) and a #10 Washer (100) into the Left Outside Upright Cover (87) and into the bottom of the left handrail assembly (D). Press the Left Inside Upright Cover (88) against the Left Outside Upright Cover (87) until they snap together...
English Manual
Page 18
To protect the floor or carpet, place a mat under the treadmill. one of the hex keys is used to the console, keep the treadmill out of plastic on the treadmill decals, remove the plastic. 18. start both Screws, and then tighten them. 6 3 53 89 19. Make sure that all parts ... damage to adjust the walking belt (see pages 30 and 31). If there are properly tightened before you use the treadmill. Note: Extra parts may be included. 18 Attach the Latch Assembly to the Left Upright (89) with 18 two 1/4" x 4 1/2" Screws (6) and two 1/4" Star Washers (3); Keep the included hex keys...
To protect the floor or carpet, place a mat under the treadmill. one of the hex keys is used to the console, keep the treadmill out of plastic on the treadmill decals, remove the plastic. 18. start both Screws, and then tighten them. 6 3 53 89 19. Make sure that all parts ... damage to adjust the walking belt (see pages 30 and 31). If there are properly tightened before you use the treadmill. Note: Extra parts may be included. 18 Attach the Latch Assembly to the Left Upright (89) with 18 two 1/4" x 4 1/2" Screws (6) and two 1/4" Star Washers (3); Keep the included hex keys...
English Manual
Page 34
... 1 83 1 84 1 85 1 86 2 87 1 88 1 89 1 90 1 91 2 92 1 93 1 94 1 95 1 96 1 Description Drive Roller/Pulley Magnet Reed Switch Clip Reed Switch Latch Assembly Drive Motor Motor Belt Frame Left Rear Foot Console Ground Wire Rubber Cushion Right Foot Rail Idler Roller Front Wheel Wheel Spacer Console Base Motor...
... 1 83 1 84 1 85 1 86 2 87 1 88 1 89 1 90 1 91 2 92 1 93 1 94 1 95 1 96 1 Description Drive Roller/Pulley Magnet Reed Switch Clip Reed Switch Latch Assembly Drive Motor Motor Belt Frame Left Rear Foot Console Ground Wire Rubber Cushion Right Foot Rail Idler Roller Front Wheel Wheel Spacer Console Base Motor...