Instruction Manual
Page 2
Apply the decal in the U.S. PROFORM and IFIT are registered trademarks of Bluetooth SIG, Inc. The BLUETOOTH® word mark and logos are a registered trademarks of Google Inc. and are trademarks... license. Note: The decal(s) may not be shown at actual size. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 PART IDENTIFICATION CHART 5 ASSEMBLY 6 HOW TO USE THE ELLIPTICAL 16 MAINTENANCE AND TROUBLESHOOTING 3. 8. .3 .1 .0 .6 . . . . . 25 EXERCISE GUIDELINES 27 PART LIST 31 EXPLODED DRAWING 33 ORDERING REPLACEMENT PARTS Back Cover ...
Apply the decal in the U.S. PROFORM and IFIT are registered trademarks of Bluetooth SIG, Inc. The BLUETOOTH® word mark and logos are a registered trademarks of Google Inc. and are trademarks... license. Note: The decal(s) may not be shown at actual size. TABLE OF CONTENTS WARNING DECAL PLACEMENT 2 IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 PART IDENTIFICATION CHART 5 ASSEMBLY 6 HOW TO USE THE ELLIPTICAL 16 MAINTENANCE AND TROUBLESHOOTING 3. 8. .3 .1 .0 .6 . . . . . 25 EXERCISE GUIDELINES 27 PART LIST 31 EXPLODED DRAWING 33 ORDERING REPLACEMENT PARTS Back Cover ...
Instruction Manual
Page 5
... parts may be included. PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity needed for assembly. The number in the hardware kit, check to identify the small parts needed for assembly. Note: If a part is not in parentheses below to see if it has been preassembled. M8 Locknut (102...
... parts may be included. PART IDENTIFICATION CHART Use the drawings below each drawing is the quantity needed for assembly. The number in the hardware kit, check to identify the small parts needed for assembly. Note: If a part is not in parentheses below to see if it has been preassembled. M8 Locknut (102...
Instruction Manual
Page 6
...have internet access, call Customer Service (see page 5. • In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet Assembly may be easier if you finish all parts in a cleared area and remove the packing materials. Then.... 1 • activates your product. 2. Do not dispose of the packing materials until you have a set of wrenches. ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To...
...have internet access, call Customer Service (see page 5. • In addition to the included tool(s), assembly requires the following tools: one Phillips screwdriver one rubber mallet Assembly may be easier if you finish all parts in a cleared area and remove the packing materials. Then.... 1 • activates your product. 2. Do not dispose of the packing materials until you have a set of wrenches. ASSEMBLY • Assembly requires two persons. • Place all assembly steps. • Left parts are marked "L" or "Left" and right parts are marked "R" or "Right." • To...
Instruction Manual
Page 26
... belt may need to pry off the Shield Cover (75) and the Shield Cover Cap (118). See assembly step 16 on page 11. Remove the Right Leg Outer and Inner Covers (69, 83). See assembly step 12 on page 13. Then, carefully remove the Right Roller Arm (59) and the Right Pedal... (73, 74). Then, retighten the Idler Screw. 113 89 91 Then, reattach the parts that you are pedaling, even while the resistance is tight. See assembly step 15 on page 35. Next, remove the M8 x 16mm Screw (95), the Large Axle Cover (53), and the M8 Washer (not shown) from the...
... belt may need to pry off the Shield Cover (75) and the Shield Cover Cap (118). See assembly step 16 on page 11. Remove the Right Leg Outer and Inner Covers (69, 83). See assembly step 12 on page 13. Then, carefully remove the Right Roller Arm (59) and the Right Pedal... (73, 74). Then, retighten the Idler Screw. 113 89 91 Then, reattach the parts that you are pedaling, even while the resistance is tight. See assembly step 15 on page 35. Next, remove the M8 x 16mm Screw (95), the Large Axle Cover (53), and the M8 Washer (not shown) from the...