RP114 Reference Manual
Page 27
...Activity) 100 (100 Mbps) Activity On Off On Off Blinking On Blinking On Blinking On Off Description Power is not ready or has failed to start up. Reference Guide for the Model RP114 Web Safe Router The Router's Front Panel The front panel of the LEDs to verify connections. Table ...2-1. The system is not supplied to the router. Power is ready and running. The system is being transmitted or received ...
...Activity) 100 (100 Mbps) Activity On Off On Off Blinking On Blinking On Blinking On Off Description Power is not ready or has failed to start up. Reference Guide for the Model RP114 Web Safe Router The Router's Front Panel The front panel of the LEDs to verify connections. Table ...2-1. The system is not supplied to the router. Power is ready and running. The system is being transmitted or received ...
RP114 Reference Manual
Page 29
...(or WAN): 1. Setting Up the Hardware 2-5 Plug the connector of the power adapter into a standard wall outlet. 3. Plug the other standard 10BASE-T Ethernet cable. To connect the Model RP114 router to your cable or DSL modem may be an Ethernet crossover cable rather... than four hosts, you can connect to the other hub's normal or uplink port, using a standard or crossover Ethernet cable. Note: The attached modem device must provide a standard 10BASE-T Ethernet connection. Note: The Ethernet cable supplied...
...(or WAN): 1. Setting Up the Hardware 2-5 Plug the connector of the power adapter into a standard wall outlet. 3. Plug the other standard 10BASE-T Ethernet cable. To connect the Model RP114 router to your cable or DSL modem may be an Ethernet crossover cable rather... than four hosts, you can connect to the other hub's normal or uplink port, using a standard or crossover Ethernet cable. Note: The attached modem device must provide a standard 10BASE-T Ethernet connection. Note: The Ethernet cable supplied...
RP114 Reference Manual
Page 125
... your Model RP114 Web Safe Router. PWR LED Not On If the PWR and other LEDs are off . • If the LAN and WAN Ethernet connections are correctly made to operational devices, each problem description, instructions are using the 12 V DC power adapter supplied by NETGEAR for 30 ...seconds, during which the Test LED should blink at a rate of about troubleshooting your router and that the power supply adapter is connected to a device that operates at 100 Mbps, the ...
... your Model RP114 Web Safe Router. PWR LED Not On If the PWR and other LEDs are off . • If the LAN and WAN Ethernet connections are correctly made to operational devices, each problem description, instructions are using the 12 V DC power adapter supplied by NETGEAR for 30 ...seconds, during which the Test LED should blink at a rate of about troubleshooting your router and that the power supply adapter is connected to a device that operates at 100 Mbps, the ...
RP114 Reference Manual
Page 126
... the router's WAN port to a cable or DSL modem, use the cable that was supplied with the Test LED: • Cycle the power to see if the router recovers and the LED blinks for about 30 seconds at the ...hub or workstation. • Make sure that power is turned on to the connected hub or workstation. • Be sure you are using the recommended ... it stops blinking and stays on, there is a fault within the router. Reference Guide for the Model RP114 Web Safe Router Test LED Never Blinks or LED Stays On When the router is turned on, the Test...
... the router's WAN port to a cable or DSL modem, use the cable that was supplied with the Test LED: • Cycle the power to see if the router recovers and the LED blinks for about 30 seconds at the ...hub or workstation. • Make sure that power is turned on to the connected hub or workstation. • Be sure you are using the recommended ... it stops blinking and stays on, there is a fault within the router. Reference Guide for the Model RP114 Web Safe Router Test LED Never Blinks or LED Stays On When the router is turned on, the Test...