NEC LCDMT810 Support and Manuals
Get Help and Manuals for this NEC item
View All Support Options Below
Free NEC LCDMT810 manuals!
Problems with NEC LCDMT810?
Ask a Question
Free NEC LCDMT810 manuals!
Problems with NEC LCDMT810?
Ask a Question
Popular NEC LCDMT810 Manual Pages
User Manual - Page 1
... disconnected before you get started, you can be is approximately 20" (0.5 m) measured diagonally when the projector is roughly 3 feet (1.0 m) from the wall or screen.
2 INSTALLATION
This section describes how to set up your MultiSync MT810 LCD projector and how to set up a screen or select a non-glossy white wall onto which you must first: 1. But...
User Manual - Page 3
... the "Menu" and "Select" buttons on your projector cabinet or (A) (7) buttons on your remote control to install the projector yourself.
13.12 ft (4 mm)
NOTE : Distances may vary ±- 5%.
235"-300-
Contact your NEC dealer for more information. If the projector falls to enjoy a much larger image. The projector must be used at temperatures between 32...
User Manual - Page 5
... manual for installation instructions.
3. INSTALLATION
USERS MANUAL
38
3-19 Consult your projector's image and monitor may be caused by a screen saver installed on the cable to connect to the projector....adapter, simply:
I on the LCD projector and the computer.
5. If the projector goes blank after a period of these following display standards are supported:
VGA 640 X 480 for graphics...
User Manual - Page 6
... NEC projectors are designed to take affect.
39
Macintosh 1. They use industry standards. By turning off your settings. INSTALLATION
...supported by XGA (1024 X 768). USERS MANUAL
Changing Video Resolutions
Depending on "Option." 3.
Open "Control Panel" and select "Display." 3. You may be asked if you to change your cursor to keep your display." Select "Change System Settings...
User Manual - Page 8
...operate your computer's mouse functions from the NEC MultiSync MT810 remote control. USERS MANUAL
Connecting Your Remote Mouse Receiver
The remote ...mouse receiver enables you to your mouse port.
3. Turn off your computer.
0 IBM PC/AT
0 INSTALLATION
Do-cm
Macintosh
W
i llIla
IBM PS/2 lOpo icip h M ....
3-22
It is installed...
User Manual - Page 11
...or cabinet to quit the menu display. The change is "on the remote control or projector cabinet to highlight the menu for the item you adjust it again. 6. SOURCE MENU
... want
to select a submenu or item. 4.
STORT
PER OFF
DFC
SETTINGS MENU
CUSTOM MEMORY ' CUSTOM 2
II'rt3E LOOP
013 BACKGROND
BLLE PROJECTION 1- USERS MANUAL
Using The Menus
I
49
0 COLOR __ a
soremmtivws;
.]
fi
...
User Manual - Page 12
... of six** custom settings you can create. ... or (-) buttons to select a standard* or one of six" custom settings you can be user changed and automatically recalled. ** "Custom 6" is ...your inputs. Press the "Select" button on the projector cabinet or (A) (V) buttons on your remote control to...input-VCR, or laser disk player. USERS MANUAL
Menu Descriptions & Functions
Source Menu
Enables you...
User Manual - Page 13
...Color Use the "Adjust" (+) or (-) buttons to adjust. Use the "Select" button on the projector cabinet or (A) (V) buttons on your image and sound. Volume Use the "Adjust" (+) or (-) ...to adjust the contrast. Contrast Use the "Adjust" (+) or (-) buttons to adjust the tint.
USERS MANUAL
Image Adjustment Menu
I or RGB 2 source is selected, the volume, brightness, contrast, horizontal position, ...
User Manual - Page 14
... move it down. Auto Picture* Use the "Adjust" (+) button to save the new setting. Picture Adjustment **(when AUTO PICTURE is evident when part of your image appears to be necessary when you can make "Picture and Fine Picture" adjustments manually. Press the "Adjust" (+) and (-) buttons until the banding disappears. This function adjusts the...
User Manual - Page 15
... This tells you replace a lamp after 2000 hours of service. After you install a new lamp, select this icon and press and hold the "Power On" button on the remote control for five minutes or more, the projector will turn itself off and go into stand by mode after replacing the lamp. NOTE: The projector will automatically...
User Manual - Page 16
...setting.
The options are : English, German, French, Italian, Spanish and Swedish. Press "Enter" on the cabinet or the "Left Click" on -screen instructions... loop
changes. Use the "Select" button on the projector cabinet or (A) (V) buttons on your remote control to... the "STANDARD" in one of projection.
USERS MANUAL
Settings Menu gilOrOttfaleik
Enables you to start an image loop...
User Manual - Page 17
... on. If you install a new lamp, select the lamp Usage icon and press and hold
the "Power On" button on
this case to prevent the risk of service. Interlock
.4 ; Do not attempt to circumvent this happens, contact your projector's model number
5.
NOTE: When you should follow to replace the lamp, clean or replace the filter, and...
TroubleShooting Manual - Page 1
... each and reattach them if necessary. TROUBLE SHOOTING
3-35 Contact your MultiSync MT810 LCD Projector.
Blinking very slowly (On and off the projector, wait one minute, then turn the projector back on too quickly.
Turn off in a cycle of operation and should be replaced. USERS MANUAL
5 TROUBLESHOOTING
This section helps you resolve problems you 're presenting is not...
TroubleShooting Manual - Page 2
... work
• Install new batteries. (See page 64.) • Make sure there are connected properly. • Use icons to see if the projector has overheated or ...projector to improve its angle to
vertically, horizontally input.
To Contact Your NEC Service Representative, Call 1-800-836-0655
TROUBLE SHOOTING
72
3-36
Status indicator is within 23 feet (7m) of the lens.
Problem...
TroubleShooting Manual - Page 9
...:
CA Err
Err 01:
Command Error (command nor supported)
Err 02:
Checksum Error
Err 03:
Busy (command not acceptable)
85
Err 04:
Parameter Error ( parameter data abnormal) PC Control Connector (DIN-8P)
NOTE: !Hailing in powering-on /off:
Communications procedure:
None Full duplex
If the CPU of PC
SPECIFICATIONS 86
3-43 If the received data...
NEC LCDMT810 Reviews
We have not received any reviews for NEC yet.