NEC LCDGT2150 Support and Manuals
Get Help and Manuals for this NEC item
View All Support Options Below
Free NEC LCDGT2150 manuals!
Problems with NEC LCDGT2150?
Ask a Question
Free NEC LCDGT2150 manuals!
Problems with NEC LCDGT2150?
Ask a Question
Popular NEC LCDGT2150 Manual Pages
GT1150/2150 - Page 1
... not indicated on the projection charts, use the values in the chart. • The ceiling must be strong enough to support the projector and the installation must be in accordance with any local
building codes. • All formulas are based on a 4:3 aspect ratio and screen. • Distances are in inches, for millimeters multiply final...
GT1150/2150 - Page 10
...RTS of PC To CTS of PC
NOTE1: Pins 1, 4, 6, and 9 are used inside the projector. Control Codes
Function
Code Data
POWER ON
02H 00H 00H 00H 00H 02H
POWER OFF
02H 01H 00H 00H 00H 03H
INPUT ... 00H 00H 16H
ON SCREEN MUTE OFF
02H 15H 00H 00H 00H 17H
Note: Contact your NEC rep for codes not listed
Cable Connection
Communication Protocol:
Baud Rate:
38400 bps
Data Length: 8 bits
Parity...
GT2150/GT1150 - Page 1
... interface card, facility managers are the benchmark for unparalleled image quality and projector performance and ease of quick-change optional lenses offer installation flexibility, even in conference rooms, CRT replacements, auditoriums, control rooms and other large venue settings. The GT1150 and GT2150 are also equipped with remote access and diagnostic control enabling management of...
GT2150/GT1150 - Page 2
...NEC Solutions (America), Inc. GT2150: 200MHz
Pixel Clock Freq
GT1150: 102MHz; Automatic set-up to UXGA with Advanced AccuBlend
GT2150... (tele)/6.2 degree(wide)
±30° electronic, for GT2150 non RGB sources ±15°
Inputs
GT1150... PC Card (service only)
Outputs
GT1150: 1 RGB, 1 RCA Audio, 1 Screen Trigger, 1 Remote (min), 1 PC Control
GT2150: 1 DVI-D,...the projector. GT2150:...
GT2150 - Page 4
...NEC Technologies in accordance with this equipment please contact your GT2150.
ALL SERVICING MUST BE DONE BY QUALIFIED NEC SERVICE PERSONNEL.
NO USER-SERVICEABLE PARTS INSIDE. This equipment has been tested and found to comply with any part...five Amps) fuse installed for use with this government regulation could void your NEC GT2150 Projector and keep the manual handy for help. ...
GT2150 - Page 6
...
• Do not put the projector on page E-52. • Be sure to replace the lamp when the message "The Lamp has
reached the end of space between your projector in a place and fasten it immediately and have the projector installed on top of glass may encounter damage caused by a qualified NEC service personnel.
3. Ensure that there...
GT2150 - Page 8
...nature, unauthorized product modification, or failure to follow instructions supplied with the product. 6.
d. Removal or installation charges. 2.
Payment of the product beyond normal operating conditions.
Any shipment of the nearest NEC Solutions authorized service center, call NEC Solutions at 800-836-0655.
4.
To obtain service on which is affected by the first purchaser, and...
GT2150 - Page 9
...subject to the following two conditions. (1) This device may cause undesired operation.
U.S. DECLARATION OF CONFORMITY
This device complies with Part 15 of Product:
LCD Projector
Equipment Classification:
Class B Peripheral
Models:
GT2150
We hereby declare that may not cause harmful interference, and (2) this device must accept any interference received, including interference that...
GT2150 - Page 10
... E-11
Signal Type E-45
2 INSTALLATION
Switcher E-45 Switcher Gain E-45
Setting Up Your GT2150 Projector E-12
Switcher Volume E-45
Screen ...TROUBLESHOOTING
White Balance E-43
Power / Status Light Messages E-56
Color Temperature E-43
Lamp Light Messages E-56
Brightness R/G/B E-43
Common Problems & Solutions E-56
Contrast R/G/B E-43 Signal Level E-43
8 SPECIFICATIONS...
GT2150 - Page 27
...17 Select the appropriate speed between 4800 and 38400.
6-3 Set the Link Mode on the slave projector.
6-3-3. Ceiling Front Projection Use [Projector Options] → [Setup] → [Page 1] → [Orientation] to select "Ceiling Front". (See page E-49.)
NEC
Ceiling Rear Projection Use [Projector Options] → [Setup] → [Page 1] → [Orientation] to activate the Link Mode
6-6 This...
GT2150 - Page 36
... clamp core
Using OUTPUT Connectors
You can connect a separate, external monitor to simultaneously view on your GT2150 projector to your projector.
3.
NOTE: The ANALOG OUTPUT connector outputs RGB signal during standby...110 MHz or over of pixel clock cannot be supported. See page E-43 for DVI digital signal. Turn on an external monitor disappears for Link mode only. Turn off the ...
GT2150 - Page 49
... 1 Page 2 Page 3
Menu Mode (Basic/Custom Menu, Advanced Menu, Service Menu) Basic/Custom Menu Edit Language (English / German / French / Italian / Spanish / Swedish / Japanese) Menu Display Time (Manual / Auto 5 sec / Auto 10 sec / Auto 30 sec) Display Select (Date, Time, Input Terminal, Source Name, Projector ID On/Off) Date Format (MM/DD/YYYY, MM...
GT2150 - Page 60
...Monitor Output connector during switching. User Name Type in your setting available, select OK. Select one of the characters, press ENTER.
[Page 5]
Projector ID Each projector needs its inputs each time the projector...standby condition. NOTE: The projector will turn this feature off and go into standby mode after replacing the lamp. The master projector is set to Slave. Power Off ...
GT2150 - Page 67
...;ן1, D-Sub 15 pinן1, RCA (L/MONO, R)ן1
Remote Control Stereo mini jack ;IN x 1; SPECIFICATIONS
This section provides technical information about the GT2150 Projector's performance. Model Number GT2150
Optical
LCD Panel Lamp Lamp Life Lens Options
Lens Shift (GT19ZL and GT34ZL) Image Size Projection Distance
Projection Angle
Electrical
Input...
Throw Distance Chart - Page 1
The ceiling must be strong enough to support the LCD projector and the installation must be in accordance with any local building codes. • All calculations are in the table. C(Tele) = 2.4231H - 3.228 GT24ZL: C(Wide) = 2.4282H - 4.799 ------- If the figures on 4:3 aspect ratio. • Distances are based on ...
NEC LCDGT2150 Reviews
We have not received any reviews for NEC yet.