NEC LCDMT1000 Support and Manuals
Get Help and Manuals for this NEC item
View All Support Options Below
Free NEC LCDMT1000 manuals!
Problems with NEC LCDMT1000?
Ask a Question
Free NEC LCDMT1000 manuals!
Problems with NEC LCDMT1000?
Ask a Question
Popular NEC LCDMT1000 Manual Pages
User Manual - Page 2
... of your NEC MultiSync MT1000 LCD Projector and keep the manual handy for a Class A digital device, pursuant to provide reasonable protection against harmful interference in this unit has been provided.
THERE ARE HIGHVOLTAGE COMPONENTS INSIDE. NO USER-SERVICEABLE PARTS INSIDE.
This equipment has been tested and found to comply with this government regulation could void...
User Manual - Page 3
... in damage to ensure the long life of your LCD projector and to support the LCD projector and the installation must be installed by a qualified NEC service person.
3.
Power Supply
1. Ensure that vents are to your projector. A damaged cord can cause electric shock or fire.
3. If the LCD projector is on a flat, level surface in accordance with a vacuum cleaner...
User Manual - Page 6
... as to follow instructions supplied with the product.
Payment of nature, unauthorized product modification, or failure to whether a dealer is warranted for service MUST have other acts of shipping charges. OR
2. FOR MORE INFORMATION, TELEPHONE 800-366-5213
NEC TECHNOLOGIES, INC. 1250 N. L I M I T E D WA R R A N T Y
NEC MultiSync® LCD Projector Products
NEC Technologies, Inc...
User Manual - Page 7
...17 Rear Features ...18 Top Features ...19 Terminal Panel Features 21 Remote Control Features 25
2. Troubleshooting
Status Light Messages ...69 Common Problems & Solutions 71
6. Installation
Setting Up Your MultiSync MT1000 LCD Projector 29 Selecting A Location 30 Using A Tabletop Or Cart 31 Ceiling Installation 33 Reflecting The Image 34 Rear Screen Projection 34
Wiring Diagram ...35-36...
User Manual - Page 8
... even be installed on the ceiling.
• Supports most IBM VGA, S-VGA, XGA, SXGA(pseudo), Macintosh, or any other RGB signals within a horizontal frequency range of 15.754 to 85 kHz and a vertical frequency range of service or six months, whichever comes first.
• A wireless remote control that operates the projector from any office...
User Manual - Page 9
...; NEC MultiSync MT1000 LCD Projector
• Remote Control With Built-In Laser Pointer And Cables
• Remote Mouse Receiver
• PC/Macintosh MultiCable (15-Pin Mini D-Sub To 15-Pin D-Sub Connector)
• Power Cable
• Two AA Batteries
• Introductory Video
• User's Manual
• Accessory Catalog
• Registration Card
Remote control...
User Manual - Page 10
... To Know Your MultiSync MT1000 LCD Projector
Front Features
Remote Sensor
Lens And ... / MONO
R
S-VIDEO INPUT
AUDIO OUTPUT
L / MONO RGB INPUT 1
R AUDIO
RGB INPUT 2
AUDIO
RGB MONITOR OUTPUT
K
Rear Feet
Main Power Switch
AC Input Plug the female end of the supplied power cable here, and the...-In Speakers (1W)
10
INTRODUCTION
Lamp Cover Set Screw
Lamp Cover
Built-In Speakers (1W)
18
User Manual - Page 11
... safely.
If this light blinks red rapidly, it means the projector's internal temperature is too hot to turn the power on and...is advisable to change the level of service. when the indicator is amber, it 's warning you ' re in the Power or Settings menus.
6 (+) (-) Zoom Buttons
...These buttons are also used to set an item in the Image Adjust mode to replace the projection lamp as soon as...
User Manual - Page 13
...
INTRODUCTION
24 MicroSaver® is trademarked and owned by Kensington Microware Inc. Use the NEC MultiCable that 's supplied. 6 RGB Input 1 Connector (D-Sub 15 pin)
Connect your computer image to an external monitor from either the RGB 1 or RGB 2 input source.
0 Built-in Security Slot ( ) This security slot supports the MicroSaver® Security System.
User Manual - Page 20
...If you to the projector's RGB 1 input. If the projector goes blank after a period of these following display standards are supported:
VGA 640ן... projector's image and monitor may be caused by a screen saver installed on the projector.)
4. Consult your computer's owner's manual for installation instructions.
37
3.
All of inactivity, it may require.
20
INSTALLATION
...
User Manual - Page 21
...supported by SXGA (1280ן1024). Method 1 1. Move your notebook's display, the timing parameters are a bit more information.
21
INSTALLATION... your settings. Select "Yes." Click on page 52 for the changes to take affect.
39
Notebook Computers And Resolution Standards NEC projectors are...NEC monitor connected to your Macintosh, you may be asked if you can use...
User Manual - Page 22
...INSTALLATION
42 Turn off the power to your LCD projector and document camera. 2. To do so, simply: 1. Turn on the LCD projector and the document camera. Turn off the power to your MultiSync MT1000 LCD Projector...a 15-pin cable to connect your monitor to keep your LCD
projector. 3. To do so: 1. NOTE: Refer to your document camera's owner's manual for stereo sound. 3.
Use standard ...
User Manual - Page 32
.... NOTE: When you install a new lamp, select the lamp Usage icon and press and hold
the "Power On" button on .
After you replace the lamp, it in the cabinet will turn off the main power to circumvent this from your NEC dealer using your replacement lamp.
Do not attempt to the projector and disconnect the...
User Manual - Page 36
... is not fastened properly. Check each and reattach them if necessary.
Contact your NEC dealer for service.
69
Blinking Slowly (On and off and back on .
5 TROUBLESHOOTING
This section helps you resolve problems you 're presenting is particularly warm, move the projector to a cooler location. • Check the filter and clean it if necessary. •...
User Manual - Page 37
... screen. • Ensure that the distance between you will be lost . To Contact Your NEC Service Representative, Call 1-800-836-0655
71
This section explains conditions that you and the projector. • Stand within 23 feet (7m) of the projector. SXGA images inherently display a 5 to 4 ratio, resulting in and that the power switch on...
NEC LCDMT1000 Reviews
We have not received any reviews for NEC yet.