Maytag MEDB765FW Support and Manuals
Get Help and Manuals for this Maytag item
View All Support Options Below
Free Maytag MEDB765FW manuals!
Problems with Maytag MEDB765FW?
Ask a Question
Free Maytag MEDB765FW manuals!
Problems with Maytag MEDB765FW?
Ask a Question
Maytag MEDB765FW Videos
Maytag MVWB765FW Washer And MEDB765FW Dryer From Costco
Duration: 9:50
Total Views: 38,290
Duration: 9:50
Total Views: 38,290
Popular Maytag MEDB765FW Manual Pages
W10240504 - Page 1
...instructions. Connect wrist strap to a green ground connection point or unpainted metal in the appliance
-OR- Contents
Whirlpool, Maytag, and Kenmore Control Panels.... 2-4 Diagnostic Guide 5 Activating the Service Diagnostic Mode 5 Key Activation & Encoder Test 6 Service Test Mode 6 Service Test Mode Chart 7, 8 Software Version Display 9
Fault/Error Codes 9, 10 Troubleshooting...
W10240504 - Page 2
... each button once to turn off its respective indicator. Press each button once to turn off its respective indicator.
Key Activation & Encoder Test for Service Diagnostic Mode, Whirlpool Models Press twice to exit service
diagnostic mode and return to standby mode. START/PAUSE button: press once to turn off
its respective indicator. FOR...
W10240504 - Page 3
...: press once to turn off indicator. Key Activation & Encoder Test for Service Diagnostic Mode, Maytag Models
Press each modifier button once to turn off the seven-segment display.
DO NOT REMOVE OR DESTROY
MAYTAG CONTROL PANEL (features and appearances may vary between models).
Rotating the cycle selector knob turns off each button once to standby...
W10240504 - Page 4
...'S USE ONLY
DO NOT REMOVE OR DESTROY
START/PAUSE button: press once to turn off the seven-segment display. Key Activation & Encoder Test for Service Diagnostic Mode, Kenmore Models
Press each button once to turn off the
status LEDs.
Time Adjust "-" button: press once to turn off indicator. Time Adjust "+" button: press...
W10240504 - Page 6
..., the dryer exits to run only the voltage test. Replace the user interface and housing assembly.
If no saved fault code, "888" will not be activated before test to enter the diagnostic mode using that are currently detected. Activation with the button, and it is displaying an active fault code. Review the Fault/Error Codes table...
W10240504 - Page 8
...The update for "ServiceTimeout" or pressing of POWER to go to 200).
Electric Dryer ...available to a 3-phase service with reduced wattage that will be displayed as in..."Check Vent" LED is turned off. If complaint is made regarding electric dryer performance ... 0.
Airflow Display
Value
0 1 2 3 (Default)
Setting
Airflow not bad Cannot detect Airflow bad; Frame 1: Htr...
W10240504 - Page 10
...TECHNICIAN'S USE ONLY
SERVICE FAULT/ERROR CODES
CODE DESCRIPTION
EXPLANATION AND RECOMMENDED PROCEDURE
F1E1 Motor Relay Stuck On
Indicates an ACU problem. • Replace the ACU. F1E3 Incorrect Controller Installed (on the ACU. F2E1 User Interface (UI) Stuck Button
Indicates a stuck button (depressed for the dryer model displaying the fault/error code. F2E4 UI Software...
W10240504 - Page 11
... dryer installation.
Moisture Sensor problem....vent. User selected invalid option. User Interface problem. Drive Belt / Belt Switch problem. ACU problem.
Perform ACU L1 and L2 tests under Service Test Mode. Heater vent...Guide". Thermistor problem.
See Test #4: Heat System, page 16. Adjust Customer Focused Dryness Level. FOR SERVICE TECHNICIAN'S USE ONLY
TROUBLESHOOTING GUIDE
PROBLEM...
W10240504 - Page 12
...P14-2
P8-1 BR DRUM LAMP
P14-1
(ON SOME MODELS)
Heater Relay #1 (Gas & Elect.)
P9
L1 - FOR SERVICE TECHNICIAN'S USE ONLY
TROUBLESHOOTING TESTS
IMPORTANT: The following procedures may require the use needle...12
DO NOT REMOVE OR DESTROY Unplug dryer or disconnect power.
2. With voltmeter set to DC, unplug connector P2 from the ACU. With voltmeter set to AC, connect black probe to ...
W10240504 - Page 13
....
11. installations, a visual inspection indicates that ALL connectors are mechanically secure.
COM
Figure 4a - If so, replace the main wire harness and test the dryer.
7. Reassemble all parts and panels.
10.
Remove the cover plate from the top right corner of the back of it. DO NOT REMOVE OR DESTROY
PAGE 13 FOR SERVICE TECHNICIAN...
W10240504 - Page 16
... following items are part of this system:
Part of Measurement
Disconnect... replace the motor.
7. The following procedure under TEST #7: Door Switch, page 22. FOR SERVICE... infinity to the dryer. Door switch problems can be uncovered by...replace the door switch assembly. NOTE: Main and Start winding coils must be checked at the motor is correct, there is an open circuit, check and repair...
W10240504 - Page 18
... an open circuit, replace both detected, replace the ACU. Reassemble all parts and panels.
11. Plug in dryer or reconnect power.
6. Perform steps under "Service Test Mode", page 6, to step 6.
6. The ACU monitors the exhaust temperature using the outlet thermistor, and cycles the heater relay on and off .
Otherwise, go to verify repair. The following...
W10240504 - Page 19
... correct the problem, replace the ACU. FOR SERVICE TECHNICIAN'S USE ONLY
NOTE: All thermistor resistance measurements must be made while dryer is unplugged and connector removed from dryer and disconnect external vent.
2.
TEST #4c: Thermal Cut-Off
If the dryer does not produce heat, check the status of the temperature levels in duration and select a temperature setting using...
W10240504 - Page 21
... Customer-Focused Dryness Level).
8. TEST #6: Buttons and Indicators
This test is displayed in dryer or reconnect power.
8. Remove console to a "3" (15% more drying time), "4" (30% more dry than START, DRYNESS, or DRY LEVEL is pressed, the dryness setting is measured, replace the sensor harness.
7. Visually check that ALL UI connectors are not present...
W10240504 - Page 26
....
NOTE: Refer to Figure 10b, page 17, for gas dryer component locations. Component locations.
FOR SERVICE TECHNICIAN'S USE ONLY
COMPONENT LOCATIONS
• ACU (beneath console) • User Interface (UI)
Door Switch (Location may vary between models)
• Drum Light Assembly • Thermal Cut-off • High Limit Thermostat • Heater Assembly
• Motor...
Maytag MEDB765FW Reviews
We have not received any reviews for Maytag yet.