Service Manual
Page 5
...Speed Is Not Reached 3-9 Wash Cycle Takes Longer Than Normal 3 - 1 0 Suds Coming Out Of Door ...3 - 1 0 Washer Will Not Start ...3 - 1 1 Motor Phase Test ...3 - 1 2 TIMER TEMPLATE OVERLAY ...3 - 1 3 MISCELLANEOUS INFORMATION ...3-14...BOOT ...7 - 1 OUTER TUB COVER ...7-2 SPIN BASKET ASSEMBLY W/BALANCE RING 7-3 DRIVE PULLEY ...7-4 SPINNER TUB SUPPORT ...7-5 16008373-01 ©1997 Maytag Corporation CONTENTS iii CABINET ASSEMBLY ...5 - 1 DOOR ASSEMBLY & HINGES ...5 - 1 Cabinet Vibration Absorber ...5-2 Door Latch Hoop ...5-2 FRONT PANEL ...5-2 TOP COVER ...5-3 DOOR LOCK MECHANISM ...5-3 FRONT...
...Speed Is Not Reached 3-9 Wash Cycle Takes Longer Than Normal 3 - 1 0 Suds Coming Out Of Door ...3 - 1 0 Washer Will Not Start ...3 - 1 1 Motor Phase Test ...3 - 1 2 TIMER TEMPLATE OVERLAY ...3 - 1 3 MISCELLANEOUS INFORMATION ...3-14...BOOT ...7 - 1 OUTER TUB COVER ...7-2 SPIN BASKET ASSEMBLY W/BALANCE RING 7-3 DRIVE PULLEY ...7-4 SPINNER TUB SUPPORT ...7-5 16008373-01 ©1997 Maytag Corporation CONTENTS iii CABINET ASSEMBLY ...5 - 1 DOOR ASSEMBLY & HINGES ...5 - 1 Cabinet Vibration Absorber ...5-2 Door Latch Hoop ...5-2 FRONT PANEL ...5-2 TOP COVER ...5-3 DOOR LOCK MECHANISM ...5-3 FRONT...
Service Manual
Page 37
... Components). The wax motors are loose. 16008373-01 © 1998 Maytag Corporation SECTION 3. If yes, then excessive suds may possibly be interfering... standoff on the belt. Did the timer advance to the washer shutting down too soon or execessive suds present. Also, examine... "Thumping" Noise In Spin: The noise could be from loose lower front weight mounting bolts or a loose bolt securing the driven pulley. "Ticking ...belt. TROUBLESHOOTING 3 - 3 Carefully remove the excess flash and remount the boot gasket. If the timing is energized for five minutes without the cycle ...
... Components). The wax motors are loose. 16008373-01 © 1998 Maytag Corporation SECTION 3. If yes, then excessive suds may possibly be interfering... standoff on the belt. Did the timer advance to the washer shutting down too soon or execessive suds present. Also, examine... "Thumping" Noise In Spin: The noise could be from loose lower front weight mounting bolts or a loose bolt securing the driven pulley. "Ticking ...belt. TROUBLESHOOTING 3 - 3 Carefully remove the excess flash and remount the boot gasket. If the timing is energized for five minutes without the cycle ...
Service Manual
Page 56
...open, unsnap the boot gasket from engagement with the rotating gear. Remove the front panel and raise the top cover to section on the sealing lip of the gasket (Figure 5-9). 16008373-01 © 1998 Maytag Corporation SECTION 5. Emergency Access Cord Mounting Screws Figure 5-8 FRONT SHROUD ASSEMBLY The shroud... (Figure 5-8). Two switches in the extended position and entry into the washer is necessary. By carefully applying both a steady pull of the access cord and opening force to the cable, removal of the washer. Remove the wires from the lock switches, wax motor and light fixture...
...open, unsnap the boot gasket from engagement with the rotating gear. Remove the front panel and raise the top cover to section on the sealing lip of the gasket (Figure 5-9). 16008373-01 © 1998 Maytag Corporation SECTION 5. Emergency Access Cord Mounting Screws Figure 5-8 FRONT SHROUD ASSEMBLY The shroud... (Figure 5-8). Two switches in the extended position and entry into the washer is necessary. By carefully applying both a steady pull of the access cord and opening force to the cable, removal of the washer. Remove the wires from the lock switches, wax motor and light fixture...
Service Manual
Page 66
... two hold down brackets (See Figure 5-6) or one of the two front support springs, grasp the hook of the washer. If the wire loop becomes bent, the result will brake the wire into the door boot. Pull the boot clamp spring hook toward the wire loop and disengage the spring from the... the other hand, press the wire loop into the door boot and not allow the wire to the front shroud by removing the two crosshead screws securing each baffle from outside of the outer tub cover. OUTER TUB & SPINNER ASSEMBLY © 1998 Maytag Corporation 7-1 Always shut off electrical power to the unit....
... two hold down brackets (See Figure 5-6) or one of the two front support springs, grasp the hook of the washer. If the wire loop becomes bent, the result will brake the wire into the door boot. Pull the boot clamp spring hook toward the wire loop and disengage the spring from the... the other hand, press the wire loop into the door boot and not allow the wire to the front shroud by removing the two crosshead screws securing each baffle from outside of the outer tub cover. OUTER TUB & SPINNER ASSEMBLY © 1998 Maytag Corporation 7-1 Always shut off electrical power to the unit....
Service Manual
Page 67
...gasket seal embedded in the tub cover. Remove the front panel, top cover and front shroud (See Front Panel, Top Cover, and Front Shroud Removal). 3. OUTER TUB & SPINNER ASSEMBLY 7 - 2 © 1998 Maytag Corporation Also, locate the large tab toward the front, with the wire loop. Pull the spring hook...Stretch the rear lip of the boot seal onto the outer tub cover. 7. Hook the end of the spring over the nearest tub cover clip to the unit. 2. 6. REPLACEMENT 1. Check alignment of the washer and secure (See Front Shroud). 8. Reposition the front shroud on top of the shroud...
...gasket seal embedded in the tub cover. Remove the front panel, top cover and front shroud (See Front Panel, Top Cover, and Front Shroud Removal). 3. OUTER TUB & SPINNER ASSEMBLY 7 - 2 © 1998 Maytag Corporation Also, locate the large tab toward the front, with the wire loop. Pull the spring hook...Stretch the rear lip of the boot seal onto the outer tub cover. 7. Hook the end of the spring over the nearest tub cover clip to the unit. 2. 6. REPLACEMENT 1. Check alignment of the washer and secure (See Front Shroud). 8. Reposition the front shroud on top of the shroud...