Makita JN1601 Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita JN1601 manuals!
Problems with Makita JN1601?
Ask a Question
Free Makita JN1601 manuals!
Problems with Makita JN1601?
Ask a Question
Makita JN1601 Videos
Makita JN1601 5 Amp 16 Gauge Nibbler
Duration: :31
Total Views: 2,755
Duration: :31
Total Views: 2,755
JN1601 Makita makaze za lim www.odigledolokomotive.rs.avi
Duration: 1:06
Total Views: 21,741
Duration: 1:06
Total Views: 21,741
AtelierulTau.ro - Masina taiat tabla Makita JN1601
Duration: 2:53
Total Views: 7,034
Duration: 2:53
Total Views: 7,034
Popular Makita JN1601 Manual Pages
Owners Manual - Page 1
...
1.6 mm (lil6")
1.2 m m 13/64")
2.5 mm (3132")
50 mm 12")
45 mm (1-25132")
2r200
261 mm (10-114")
1.6 kg (3.5 Ibs)
* Manufacturer reserves the right to change specifications without notice. * Note: Specifications may differ from country to country. cutting capacities Mild steel Stainless Aluminum
Min. MODEL JN1601
INSTRUCTION MANUAL
DOUBLE INSULATION
SPECIFICAT10NS
Max.
Owners Manual - Page 2
...electric shock, fire and/or serious personal injury. Double Insulated tools are doing and use the cord t o carry the tools or pull the plug from heat, oil, sharp edges or moving parts. SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS...and understand all instructions listed below, may result in serious personal injury. When operating a power tool outside, use tool while tired ...
Owners Manual - Page 3
... accidents are dangerous in . Tool service must be repaired. 18. Use of untrained users. 20. Remove adjusting keys or switches before making any other untrained persons. Use clamps or other practical way t o secure and support the workpiece t o
a stable platform. Any tool that are easier to follow Maintenance Instructions may be used on . Keep cutting tools sharp and...
Owners Manual - Page 4
Specific Safety Rules
1.
volts amperes
herts
hours minutes
alternating current
direct current
no load speed
alternating or direct current... the tool towards the rear.
.
3.Do not touch the blade or the workpiece immediately after operation; SAVE THESE INSTRUCTIONS. SYMBOLS
The followings show the symbols used for tool. Always be extremely hot and could burn your skin.
Owners Manual - Page 5
... the die holder from the die holder. Remove the die from the tool. Then install the die holder on the die holder. D1e= Bolts
5 Use the hex wrench to secure the die. Tighten the bolts to loosen the screw which secure the die. After replacing the punch and die, lubricate them with the wrench. Use the hex wrench to secure the punch.
Pull the punch out of the punch holder...
Owners Manual - Page 6
... to any of the positive stop positions as follows.
1. To position the die to secure the die
holder in the desired position. Switch lever
6 .
The die position can be sure that it is switched off and unplugged before changing the die posi- The die holder will lock into position. 4. tion. Loosen the lock nut with the wrench...
Owners Manual - Page 7
... the notch to increase the punch and die service life.
Move the tool gently in diameter which the cutting head can be done by first opening a round hole over 21 mm in the cutting direction. Gauge for cutting
stainless: 1.2 mm
Gauge for allowable cutting thick- Thickness g-aug-e
I
7
I
The grooves in the die holder indicates your cutting line...
Owners Manual - Page 8
... angle to grooves
Cutting head should be at a right angle (90")to cutting surface. From the side view
sheet metal
8 Cuttingthe corrugated or trapezoidalsheet metals Set the die position so that the die faces the cutting direction either when cutting a t an angle or perpendicular to grooves in Fig.
Owners Manual - Page 9
... Authorized or Factory Service Centers, always using Makita replacement parts.
9
Use only identical carbon brushes. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. Replacing carbon brushes Remove and check the carbon brushes
the same time. Limit mark
,-Brush
holder cap
Screwdriver /
To maintain product SAFETY AND RELIABILITY, repairs, any other...
Owners Manual - Page 10
... for use of any other accessories or attachments might present a risk of injury to persons. Die Part No.
The use with your Makita tool specified in the proper and intended manner.
A-I 5051
*Punch Part No. ACCESSORIES
CAUTION:
. A-I 5067
*Hex wrench
Part No. 783208-8
u
*Wrench 32 Part No. 781013-7
10 The accessories or attachments should be used only in this
manual.
Owners Manual - Page 11
NIBBLER Model JN1601
Nav.--29-'94 EN
d
Note: The switch, noise suppressor and other part configurations may differ from country to country.
11
Owners Manual - Page 12
... not apply to you. alterations have other part specifications may not apply to you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. THIS DlSCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. N 2t(D
MODEL JN1601 DESCRIPTION
M:i'
D:$
DESCRIPTION
Nov-12-'96 US...
Parts Breakdown - Page 2
...
783208-8 810247-6
Part Name P.T. BOLT M5X8, 2012 PUNCH, JN1601 PUNCH,JN1601
.DIE, JN1601 DIE HOLDER, JN1601 HEX SOCKET HEAD BOLT M3X12, JN1601 LOCK NUT, JN1601 TAPPING SCREW 4X65, HP2030 MAKITA LABEL, DA3010F BRUSH HOLDER, JN1601 CARBON BRUSH 408 SET, 3901 CARBON BRUSH SET CB-408, KP0800K
BRUSH CAP , 9031 SWITCH, 9564CV COMPRESSION SPRING 4, JN1601 SWITCH LEVER, JN1601 SUPPORT, JN1601 CORD GUARD...
Makita JN1601 Reviews
We have not received any reviews for Makita yet.