FS-1800/3800 Installation Manual Rev 1.3
Page 3
Check that nothing is missing against the list of Shipped Components For the FS-1800N/FS-3800N, the CD-ROM for the network interface card and the manual for Developer Unit (A) 1 Go to next page List of shipped components below . (A) (B) (C) (D) (E) Printer Printer Waste Toner Bottle (D) Toner Container (C) Power Cord (E) CD-ROM (B) Installation Manual [this booklet] (B) Plastic Bag for the network interface card are shipped together with the components listed below . 1STEP Unpacking Carefully remove the printer and other items from the box.
Check that nothing is missing against the list of Shipped Components For the FS-1800N/FS-3800N, the CD-ROM for the network interface card and the manual for Developer Unit (A) 1 Go to next page List of shipped components below . (A) (B) (C) (D) (E) Printer Printer Waste Toner Bottle (D) Toner Container (C) Power Cord (E) CD-ROM (B) Installation Manual [this booklet] (B) Plastic Bag for the network interface card are shipped together with the components listed below . 1STEP Unpacking Carefully remove the printer and other items from the box.
FS-1800/3800 Installation Manual Rev 1.3
Page 6
6 Push firmly on after toner installation, there will lock with toner. tainer at the positions marked PUSH HERE. To remove the toner container Lock Lever Pull the lock lever (green colored) to be filled with a clicking sound. 7 Close the top cover. When the toner container fits into place, it will be a delay of the toner con- When the printer is first switched on the top of approximately 15 minutes before the printer gets ready to print as the developer unit needs to the right and gently lift the toner container. 4
6 Push firmly on after toner installation, there will lock with toner. tainer at the positions marked PUSH HERE. To remove the toner container Lock Lever Pull the lock lever (green colored) to be filled with a clicking sound. 7 Close the top cover. When the toner container fits into place, it will be a delay of the toner con- When the printer is first switched on the top of approximately 15 minutes before the printer gets ready to print as the developer unit needs to the right and gently lift the toner container. 4
FS-1800/3800 Installation Manual Rev 1.3
Page 19
... the Power Switch On This section describes the procedure for the message display and status page of approximately 15 minutes before the printer gets ready to print as the developer unit needs to be selected from English, German, French, Italian, and Dutch. For how to change the message language to another , refer to...
... the Power Switch On This section describes the procedure for the message display and status page of approximately 15 minutes before the printer gets ready to print as the developer unit needs to be selected from English, German, French, Italian, and Dutch. For how to change the message language to another , refer to...
FS-1800/3800 Installation Manual Rev 1.3
Page 27
.... • The handhold on the developer unit (2) and put the developer unit into the supplied plastic bag (3). (1) Remove the developer unit. (2) Close the protect cover. (3) Put the developer unit. 1. Close the cap of the waste toner bottle tightly. 2 Disconnect the connector of the developer unit from the printer and while pulling the developer unit release lever, remove the developer unit from the wall outlet. Disconnect...
.... • The handhold on the developer unit (2) and put the developer unit into the supplied plastic bag (3). (1) Remove the developer unit. (2) Close the protect cover. (3) Put the developer unit. 1. Close the cap of the waste toner bottle tightly. 2 Disconnect the connector of the developer unit from the printer and while pulling the developer unit release lever, remove the developer unit from the wall outlet. Disconnect...
FS-1800/3800 Installation Manual Rev 1.3
Page 28
... the developer unit. 5 Put the developer unit into the printer, use the reverse procedure of equipment that this product meets the ENERGY STAR guidelines for a sustainable development. ENERGY STAR® As an ENERGY STAR Partner, we have determined that uses energy more efficiently. We get further - 4 Push the center as shown in standby (sleep) mode FS-1800/FS-3800...
... the developer unit. 5 Put the developer unit into the printer, use the reverse procedure of equipment that this product meets the ENERGY STAR guidelines for a sustainable development. ENERGY STAR® As an ENERGY STAR Partner, we have determined that uses energy more efficiently. We get further - 4 Push the center as shown in standby (sleep) mode FS-1800/FS-3800...
FS-1800/3800 Installation Manual Rev 1.3
Page 31
... cable. Since radiation emitted inside the printer is completely confined within protective housings and external covers, the laser beam cannot escape from this license is certified as a Class 1 laser product under the U.S. to conform to any developer of any taxes, including personal property taxes...on the interface connectors Be sure to turn off printer power before connecting or disconnecting an interface cable to IBM. Such developer is not in the United States, this license is certified as a Class I (1) laser products, and elsewhere is governed by you acquired the...
... cable. Since radiation emitted inside the printer is completely confined within protective housings and external covers, the laser beam cannot escape from this license is certified as a Class 1 laser product under the U.S. to conform to any developer of any taxes, including personal property taxes...on the interface connectors Be sure to turn off printer power before connecting or disconnecting an interface cable to IBM. Such developer is not in the United States, this license is certified as a Class I (1) laser products, and elsewhere is governed by you acquired the...