Quick Start Guide
Page 7
... video display when engaging the shift knob of rear camera to "Reverse". The function of high power signal. ( ) Sets to 100 steps can be set . Returns to the previous screen. • When touching [SET ] or [Initialize], make sure [Panel Color Scan] is connected. Sets the power ...SW Setup SW1 Name/ SW2 Name Output Pattern Pulse Set Sets the name of CMOS-300. When setting to the preset buttons ([Preset1] - [Preset3]). Panel Color Coordinate SET Select a color [Blue] ... [White] Sets the selected color. [Adjust] Sets and registers favorite color to "ON", camera adjustment ...
... video display when engaging the shift knob of rear camera to "Reverse". The function of high power signal. ( ) Sets to 100 steps can be set . Returns to the previous screen. • When touching [SET ] or [Initialize], make sure [Panel Color Scan] is connected. Sets the power ...SW Setup SW1 Name/ SW2 Name Output Pattern Pulse Set Sets the name of CMOS-300. When setting to the preset buttons ([Preset1] - [Preset3]). Panel Color Coordinate SET Select a color [Blue] ... [White] Sets the selected color. [Adjust] Sets and registers favorite color to "ON", camera adjustment ...
Quick Start Guide
Page 21
... ("PROTECT" is displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and the protection function may be turned on the panel surface when installing the unit to a negative 12V DC power supply. • Do not install the unit in the car. • When only two ...'s ignition does not have been activated. The unit may drop if there are being connected to the system, connect the connectors either to both the rear output terminals (do not connect the - shown in the console of your vehicle. English | 21 For best safety, leave the mounting and wiring work...
... ("PROTECT" is displayed), the speaker wire may have a shortcircuit or touched the chassis of the vehicle and the protection function may be turned on the panel surface when installing the unit to a negative 12V DC power supply. • Do not install the unit in the car. • When only two ...'s ignition does not have been activated. The unit may drop if there are being connected to the system, connect the connectors either to both the rear output terminals (do not connect the - shown in the console of your vehicle. English | 21 For best safety, leave the mounting and wiring work...
dnx7180 (pdf)
Page 108
...Rear/ Subwoofer : 0 - 14.4 ft (0.07 ft Step) Position : 0 - 5.58 ft (0.07 ft Step) Subwoofer level : -50 - +10 dB ■■Navigation section Receiver : High-sensitivity GPS receiver Reception Frequency : 1575.42 MHz (C/A code) Acquisition Times Cold : DNX5180: < 38 seconds DNX7180, DNX7480BT, DNX6980, DNX6180,... DNX6040EX, DNX6480BT: 38 seconds (typ) (On average for the liquid crystal panel is given as 99.99% or more, 0.01% of the sky) Accuracy Position : < 10 meters, ...
...Rear/ Subwoofer : 0 - 14.4 ft (0.07 ft Step) Position : 0 - 5.58 ft (0.07 ft Step) Subwoofer level : -50 - +10 dB ■■Navigation section Receiver : High-sensitivity GPS receiver Reception Frequency : 1575.42 MHz (C/A code) Acquisition Times Cold : DNX5180: < 38 seconds DNX7180, DNX7480BT, DNX6980, DNX6180,... DNX6040EX, DNX6480BT: 38 seconds (typ) (On average for the liquid crystal panel is given as 99.99% or more, 0.01% of the sky) Accuracy Position : < 10 meters, ...
Quick Start Guide
Page 22
...do not connect the connector to decrease the internal temperature. To prevent a short circuit, do not mix front and rear). Blocking these openings will not hit the lid when closing and opening. • If the fuse blows, first ...being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not remove the caps on and off with battery wires, the battery may drop if..." is installed, check whether the brake lamps, blinkers, wipers, etc. on the panel surface when installing the unit to which they correspond.
...do not connect the connector to decrease the internal temperature. To prevent a short circuit, do not mix front and rear). Blocking these openings will not hit the lid when closing and opening. • If the fuse blows, first ...being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not remove the caps on and off with battery wires, the battery may drop if..." is installed, check whether the brake lamps, blinkers, wipers, etc. on the panel surface when installing the unit to which they correspond.