Icom IC-A14 Support and Manuals
Icom IC-A14 Videos
Popular Icom IC-A14 Manual Pages
Instruction Manual - Page 1
YIC-A14
YIC-A14S INSTRUCTION MANUAL
VHF AIR BAND TRANSCEIVER
iA14 iA14S
This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
Instruction Manual - Page 3
The IC-A14/S VHF AIR BAND TRANSCEIVER is designed and built with Icom's state of personal injury, fire or electric shock.
NOTE
If disregarded, inconvenience only.
t
y
ii IMPORTANT
READ ALL INSTRUCTIONS carefully and completely
before using the transceiver. No risk of the art technology and craftsmanship. With proper care this product should provide you for the IC-A14/S. q ...
Instruction Manual - Page 5
... (Available with the IC-A14 only) 12 n Programming a memory channel 13 n Memory names 15 n Copying memory contents 16
n Clearing the memory contents (Available with the IC-A14 only 17
5 SCAN OPERATION 18-20 n Scan types 18 n COM band scan 18 n Memory scan 19 n Weather channel scan (Available with the IC-A14 only)� 19 n "TAG" channel setting 20
6 OTHER FUNCTIONS...
Instruction Manual - Page 8
...Available with IC-A14 only)
Inputs digit "1" for frequency input or memory channel selection, etc. (pgs. 8, 12)
Inputs "1," "Q," or "Z" during memory name programming. (p. ..."5," "J," "K," or "L" during memory name programming. (p. 15)
After pushing [FUNC], enters duplex transmit frequency programming condition, during NAVI band operation. (p. 24)
Inputs digit...
Instruction Manual - Page 10
... function is necessary.
!1 FREQUENCY READOUT Shows the operating frequency, memory channel
number, memory name, set as a TAG channel. The attached battery pack requires recharging when this indicator ON. Blinks when battery replacement is in use.
y DUPLEX INDICATOR (IC-A14 only) (p. 24) Appears when the duplex function is selected.
w MEMORY INDICATOR (p. 12)
Appears...
Instruction Manual - Page 15
... appears. CAUTION: Transmitting without an antenna may damage
1
the transceiver.
2
w P ush [SQLZ] several times until the channel is muted.
• " " indicator disappears. t Set the desired frequency using [Y]/[Z] or keypad (IC-A14 only). • COM band frequency range: 118.00-136.975 MHz
w Push and hold the transceiver too close to adjust the audio level. If the frequency...
Instruction Manual - Page 17
...
tion mode.
7
mode is dis-
5
played briefly. • Memory bank number also displays with the IC-A14 only)
2
fault setting) and IC-A14S has 100 memory channels for sim-
4
q Push [MR] to enter
11
• If no memory CH is programmed, no
memory CH selection is available. the desired memory
12
Using the Keypad- 4 MEMORY OPERATION...
Instruction Manual - Page 18
... frequencies with the following instructions. D For IC-A14
q Push [CLR] to complete the programmig.
13
Push
to select the frequency mode, if necessary. Blinks when select memory write mode is selected. Push
Push
then
Push or ,
or, push
Push
then
Push
then
Push
then
*Shows briefly. t Push [ENT] to program the set condition into the...
Instruction Manual - Page 19
...
number. to program the set condition into memory
4
w Set the desired frequency. (p. 8)
channel 51.
5
e Push and hold
16
for 1 sec. Push or
13 14
*Shows briefly.
15
Push and hold [MR] for 1 sec.
Push
6
• Memory mode indicator blinks.
7
Blinks when select memory
8
write mode is
10
selected.
MEMORY OPERATION 4
1
2
3
D For IC-A14S
q Push [CLR...
Instruction Manual - Page 20
... a space (displayed as "_"). ing and holding [MR] for 1 sec. D Programming memory names
q Set the desired frequency in frequency mode. (p. 8) w Enter the select memory write mode.
• For IC-A14; push [FUNC] then push [MW](MR). • For IC-A14S;
For IC-A14S t Push [Y]/[Z] several times to select the
desired character as listed at the same time. • Return...
Instruction Manual - Page 23
...-
13
tower frequencies.
14
WEATHER CHANNEL SCAN Repeatedly scans all "TAG" memory chan- COM BAND SCAN 108.00 118.00
w Push [SQLY]/[SQLZ] to set the squelch level to the point where noise is just muted.
3
136.975 Repeatedly scans
For IC-A14
4
MHz MHz
MHz a l l f r e q u e n c i e s
e Push [FUNC], then push [SCAN](2) to start the scan...
Instruction Manual - Page 24
... setting to start the scan. • When a signal is received, the scan pauses until it disappears. • To change the scanning direction, push [Y]/[Z].
For IC-A14S e Push and hold [Y]/[Z] for 1 sec.
Decimal point blinks during scan.
[Z] [Y]
[MR] [SCAN](2)
Decimal point blinks during scan.
[Z] [Y] [SCAN](2)
[WX](7)
[FUNC]
[FUNC] 19 5 SCAN OPERATION
n Memory scan
NOTE: Program...
Instruction Manual - Page 29
... turn the duplex
function ON.
8
• "DUP" blinks and transmit frequency appears. Set a duplex frequency before programming the memory channel, if desired.
e P ush and hold [PTT] to call a flight service station
2
while receiving a VOR station. OTHER FUNCTIONS 6
n Duplex operation (Available with the IC-A14 only)
1
The duplex function allows you to transmit on the pre...
Instruction Manual - Page 39
... level.
• Set COM band in set mode. Transmitting impossible.
• Volume level is too low.
• WX channels or NAVI band is selected. • The battery is exhausted.
• Set [VOL] to the threshold point.
p. 22 IC-A14S: Turn the beep tone ON in frequency mode. • Recharge the battery pack. 9 TROUBLESHOOTING
If your transceiver seems to be...
Instruction Manual - Page 40
... supply requirement : Specified Icom's battery packs
7.4 V DC standard
• Usable temperature range : -10˚C to +60˚C (+14°F to change without notice or obligation.
35 dyne
• Intermediate frequencies : 1st 46.35 MHz, 2nd 450 kHz
• Sensitivity
:
COM band (6 dB S/N) -6 dBµ typical
NAVI band (6 dB S/N) -3 dBµ typical (IC-A14 only)
WX channels...
Icom IC-A14 Reviews
Do you have an experience with the Icom IC-A14 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Icom yet.
Earn 750 points for your review!