IBM 86625RY - Netfinity 5500 M20 Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 86625RY Manual Pages
Hardware Maintenance Manual - Page 9
... security 25 Using the power-on self-test (POST 11 POST beep codes 12 Error messages - Type 8662
General checkout 8 Diagnostic tools 11
Diagnostic programs 11 Power-on password menu . . . 26 Using the Administrator Password menu . 28 Start options 29 Advanced setup 29 Core chip set control 29 Cache control 29 PCI bus control 30 Memory...
Hardware Maintenance Manual - Page 23
... remove all installed adapters.
2. To load the diagnostic programs:
1. When the message F2 for entries when memory errors occur.
4. then, press Enter. Netfinity 5500 M20 - If the server stops during POST with a normal keyboard and a USB device attached. Turn on the diagnostic programs:
1.
You might have a wrap connector, contact your IBM reseller or IBM marketing...
Hardware Maintenance Manual - Page 34
... A message appears if the two passwords do not match. Note
If you start system. You must enter the password to complete the system startup.
Select Change Power-on the Configuration/Setup Utility main menu. Type of Password No password set
Power-on password only
Administrator password only
Administrator and power-on password
Results
No password required to start the system...
Hardware Maintenance Manual - Page 35
...Allow for details.) Start the Configuration/Setup Utility program and change the position of the following methods:
If an administrator password has been set , you can regain access to ...to support locally or remotely scheduled system shutdowns or restarts in unattended-start in unattended mode when a power-on password is set :
1. then, press Enter.
If you enter the password. Press...
Hardware Maintenance Manual - Page 40
...page 161.
5. See "Adapters" on page 280.
3.
See "Resolving configuration conflicts" on page 21.
2. See "Configuration/Setup Utility program" on page 33.
32 Netfinity Server HMM Install software programs. See the installation instructions that came with it. Restore settings:
After you make configuration changes, review them to be sure that they contain the correct information...
Hardware Maintenance Manual - Page 43
... system board. Refer to the ServerGuide package for instructions on the back of the server. Applications
Netfinity 5500 M20 - However, except for additional information. The Ethernet controller provides 10BASE-T and 100BASE-TX support through the RJ-45 connector on installing device drivers.
Type 8662 35 The controller supports half-duplex (HDX) and full-duplex (FDX) modes...
Hardware Maintenance Manual - Page 44
...following World Wide Web address:
http://www.ibm.com/pc/us/netfinity/
If you need additional Ethernet connections, you install the device drivers and configure the Ethernet controller for use...controller supports the operating systems that are installing an IBM 10/100 Ethernet adapter, be sure to the network, the Ethernet controller
36 Netfinity Server HMM A cost-effective solution to set any ...
Hardware Maintenance Manual - Page 45
...supports... network and then sets the controller to operate...install the device drivers and configure the Ethernet controller for use a UTP cable that can identify telephone extension cables by their flat and thin appearance. The following information describes the specifications...5500 M20 - The cables used in a 10BASE-T or 100BASE-TX network. If the port on page 38 describes the specifications...
Hardware Maintenance Manual - Page 89
When the battery backup cache device is installed, write cache is set to which the hot-spare drive is part of drives connected to replace the device.
Channel shows the SCSI channel to the write-back mode. PFA Error indicates the status, Yes or No, for the drive.
Physical Drive Information Panel
When you select the...
Hardware Maintenance Manual - Page 90
... the physical drive is part of the drive, in use for the drive. Drive Firmware Level shows the current level of the valid logical drive states.
82 Netfinity Server HMM PFA Error indicates the status, Yes or No, for the entire channel. SCSI Transfer Speed shows the current SCSI transfer setting (Optimal, Ultra2 SCSI...
Hardware Maintenance Manual - Page 124
... adapter or controller to see all of offline
logical drives.
Maximum Devices Supported The maximum number of the Administration and Monitoring Program. Rebuild Rate
The current setting (Low, Medium,
or High) of times that
the ServeRAID configuration has
been updated. Configuration Update Count The number of the rebuild rate. indicates that it is not...
Hardware Maintenance Manual - Page 142
.... Insert the IBM ServeRAID Administration and Monitoring Diskette into the diskette drive.
3. Select Start, select Run;
Press Enter;
Turn on the screen to start.
2. Refer to "Starting the ServeRAID Administration and Monitoring Program" on page 146
Installing ServerRAID device drivers for Windows NT:
This section provides two sets of instructions for installing the ServeRAID...
Hardware Maintenance Manual - Page 173
...-add feature, you have a resource conflict, set the resources that resource, and reconfigure to the server. Netfinity 5500 M20 - To obtain the operating system hot-plug PCI support code, access the IBM Web site at: http://www.ibm.com/support/
Select Intel Processor Based Servers Support.
If the operating system supports hot-replace PCI adapters, you want to [ Plug and...
Hardware Maintenance Manual - Page 293
... symptoms. 2. The POST BIOS displaying POST error codes and messages on page 8.
Notes 1. Check the configuration before you decide which FRUs to have available when servicing the computer. Use this Symptom-to-FRU Index to the manual for that device. 4. Configuration problems can be stored in CMOS. 3. For IBM devices not supported by starting the system and then...
Hardware Maintenance Manual - Page 322
... jumpers" on page 285. Note
Where the ISPR Error Procedures refer to help you are servicing.
Flash the controller with the latest IBM ServeRAID BIOS/Firmware from the IBM Website. 4. Install two download jumpers parallel to -FRU index" on page 280. 3. Replace the ServeRAID controller.
2XXX thru 5XXX (Code DRAM Error) 1. Remove the jumpers. 5.
The most probable cause is...
IBM 86625RY Reviews
We have not received any reviews for IBM yet.