IBM 86605SU - Netfinity 5500 - 5SU Support and Manuals
Get Help and Manuals for this IBM item
Popular IBM 86605SU Manual Pages
Maintenance Manual - Page 6
... POST Beep Codes 11 Error Messages 12
POST Error Messages 12 Diagnostic Error Messages 12 Software-Generated Error Messages . . . . . 12 System Error Log 12 Option Diskettes 12 Diagnostic Programs 13 Running Diagnostic Programs 13 Viewing the Test Log 14 Features 15 Additional Service Information 17 Administration and Monitoring Utility Program . . 18 Before You Begin 19 Installing the...
Maintenance Manual - Page 11
... Beep Symptoms 263 No Beep Symptoms 266 Control Panel System Error LED 266 Diagnostic Error Codes 269 Error Symptoms 272 Power Supply LED Errors 273 POST Error Codes 275 SCSI Error Codes 280 ServeRAID II Controller Error Codes/Messages 281 System Board LEDs 285 System Board SCSI LEDs 285 Undetermined Problems 286 Parts Listing (Type 8660 288 System 289 Hard Disk Drives and...
Maintenance Manual - Page 18
.... You can select different categories. Netfinity 5500 -
Running Diagnostic Programs: While you run the diagnostic programs, a single problem might cause several error messages. That is corrected, the other error messages usually will not occur the next time you are attached to the server.
If the problem persists, have to install a wrap connector on your active parallel...
Maintenance Manual - Page 20
... access memory (SDRAM), error correcting code (ECC) Four dual ...IBM Netfinity NetBAY3 (tower model only) allows installation of the Netfinity 5500. Four 32-bit hot-plug PCI slots Two standard (non-hot-plug) 32-bit PCI slots One 16-bit ISA slot Upgradable Firmware BIOS, diagnostics, system management processor, and ServeRAID II upgrades (when available) can be installed. User log-in password...
Maintenance Manual - Page 54
... hot-swap rebuild parameter is set to Enable The defunct drive is part of a RAID level 1 or RAID level 5 logical drive The capacity of the replacement drive is equal to or greater than the capacity of the firmware microcode for the ServeRAID controller.
On - The maximum numbers of devices supported. The current version level of...
Maintenance Manual - Page 60
...install an Ethernet adapter, such as auto-negotiating. The Ethernet controller provides 10BASE-T and 100BASE-TX support...also known as the IBM 10/100 PCI Ethernet
Netfinity 5500 - However, you use...5500 comes with an Ethernet controller on the network and then sets the controller to operate at the appropriate rate. When you connect your operating system before you must install a device driver...
Maintenance Manual - Page 62
..." on the device. See "Configuration/Setup Utility Program" on the server system board. Set jumpers or switches on page 60.
2.
Run the Configuration/Setup Utility program and record the current configuration settings. See the instructions that came with the adapter.
4. Netfinity 5500 - Install software programs. See the installation instructions that came with it. See...
Maintenance Manual - Page 79
... system. Software Installation
Use ServerGuide to this manual for the specific operating system you are installing.
1.
After you configure your disk arrays, use the information provided in your ServerGuide package to install your operating system. To install application programs, refer to do next? You must use the IBM ServeRAID Configuration program to install your operating...
Maintenance Manual - Page 99
... to start system.
Power-on password provides access to a limited set
Power-on password only
Administrator password only
Administrator and power-on password
Results
No password required to start the operating system. Select System Security. 2. Follow the instructions on the screen. After you set a power-on or administrator password, you must enter the password when you turn on the server...
Maintenance Manual - Page 109
... 104. 6. A screen similar to install your operating system. IBM ServeRAID Adapter Disk Array Configuration Ver. Define..., press Enter. If you have completed the required steps for instructions. 8. As you select each drive that drive changes from the...state of that you have finished creating your disk arrays manually. Select Create/Delete/Copy Log Drive from ready (RDY...
Maintenance Manual - Page 121
... settings to identify drives, to control power to specific drives, and to the Advanced Functions menu. 6. 1. Change Adapter Host/SCSI ID lets you view the current settings (On or Off) for instructions...Monitor utility program, which direct access storage device (DASD) bank is set the start up simultaneously, and set to 20 MHz, the SCSI bus for the ServeRAID controller. Changing Device...
Maintenance Manual - Page 130
...RDY. (See "Internal Drive Installation" on page 197 and "Changing Device States" on page 126 for instructions.) 6.
then, press Enter.
3.
then, set the state for the new... drive to save. 5. See "Backing Up the Disk-Array Configuration" on page 116 for instructions.) If the drive is defective, physically replace...
Maintenance Manual - Page 144
...Setting the BootCd Feature" on page 118.) No. of the firmware...Code Bk shows the current version number of DDD Drv. shows the current number of times that the configuration has been updated. Cfg. Updates shows the current number of critical logical drives. Locked, Bad Stripe, or Blocked Drive identifies the logical drives that the firmware EEPROM has been updated...Netfinity 5500 -...; Update is...
Maintenance Manual - Page 237
...Installing and Removing the Server: During
the installation procedure, you must install parts on top of the rack model of the server. Rack Installation
Use the following items: - Review the preinstallation information in "Specifications... information, refer to the IBM Netfinity Rack Configurator program provided with all the rack installation hardware (rack model only). An assortment of small...
Maintenance Manual - Page 280
...System Board
1. Run Configuration/Setup
2. System Board
1. Processor Board
Netfinity 5500 - FRU/Action
1. System Board 2. Processor Board
1. Battery/CMOS chip 3. Failing Device 4. System Board
1. Run Configuration/Setup
2. Failing ISA Adapter 2. Failing Adapter 2. Optional Processor
(if installed) 3. System Board
1. Error Code/Symptom
062 (Three consecutive boot...
IBM 86605SU Reviews
We have not received any reviews for IBM yet.