Product Manual
Page 6
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 7HEN USING AN ELECTRICAL APPLIANCE BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDINGTHEFOLLOWING READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. s WARNING: 4HIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE 3TATE OF #ALIFORNIA TO CAUSE CANCER BIRTH DEFECTS OR REPRODUCTIVE HARM WASH HANDS AFTER HANDLING. 3 WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY: s &ULLYASSEMBLEBEFOREOPERATING s /PERATEVACUUMONLYATVOLTAGESPECIFIEDONDATALABELONBOTTOMOFCLEANER s $ONOTLEAVEAPPLIANCEWHENPLUGGEDIN5NPLUGFROMOUTLETWHENNOTINUSEAND ...
IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 7HEN USING AN ELECTRICAL APPLIANCE BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED INCLUDINGTHEFOLLOWING READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE. s WARNING: 4HIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE 3TATE OF #ALIFORNIA TO CAUSE CANCER BIRTH DEFECTS OR REPRODUCTIVE HARM WASH HANDS AFTER HANDLING. 3 WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY: s &ULLYASSEMBLEBEFOREOPERATING s /PERATEVACUUMONLYATVOLTAGESPECIFIEDONDATALABELONBOTTOMOFCLEANER s $ONOTLEAVEAPPLIANCEWHENPLUGGEDIN5NPLUGFROMOUTLETWHENNOTINUSEAND ...
Product Manual
Page 11
...15. Cord 7 18 17. 2-in the upright position. To turn vacuum OFF, push switch again. HOW TO USE VACUUM DESCRIPTION 1. CORD STORAGE 2.4 Wrap cord on cord hooks for household use. *Available on bottom of cleaner. Brushroll ON/OFF Switch 20 15 12. Furniture Guard 20. Wand ...Handle 2. Dirt Cup Release Button 5. Brushroll Window 11 4 13 9. Hose Connector 19. To turn vacuum ON, push ON/OFF switch (A) once. Short Handle Release Button 2.1 3. This cleaner is intended for convenient storage. 2.4 Attach the plug end to the cord. 2.5 Twist upper cord...
...15. Cord 7 18 17. 2-in the upright position. To turn vacuum OFF, push switch again. HOW TO USE VACUUM DESCRIPTION 1. CORD STORAGE 2.4 Wrap cord on cord hooks for household use. *Available on bottom of cleaner. Brushroll ON/OFF Switch 20 15 12. Furniture Guard 20. Wand ...Handle 2. Dirt Cup Release Button 5. Brushroll Window 11 4 13 9. Hose Connector 19. To turn vacuum ON, push ON/OFF switch (A) once. Short Handle Release Button 2.1 3. This cleaner is intended for convenient storage. 2.4 Attach the plug end to the cord. 2.5 Twist upper cord...
Product Manual
Page 14
HANDLE POSITIONS 2.6 The handle of your cleaner has two positions: upright for general operation on floors. 3.2 A B 7 Unplug vacuum before connecting hose, wand or tools. hold nozzle with foot (E) and pull handle back. 2.6 ! E 3. operating position for storage and when using cleaning ... above the floor and for tool use when handle is ready for reaching hard to be used for general operation on carpet and floors; The vacuum is in hose connector by flipping down hose connector door (B) insert hose connector (A) until it clicks. 3.1 A ! Not to clean areas. CAUTION ! ...
HANDLE POSITIONS 2.6 The handle of your cleaner has two positions: upright for general operation on floors. 3.2 A B 7 Unplug vacuum before connecting hose, wand or tools. hold nozzle with foot (E) and pull handle back. 2.6 ! E 3. operating position for storage and when using cleaning ... above the floor and for tool use when handle is ready for reaching hard to be used for general operation on carpet and floors; The vacuum is in hose connector by flipping down hose connector door (B) insert hose connector (A) until it clicks. 3.1 A ! Not to clean areas. CAUTION ! ...
Product Manual
Page 26
...before servicing. 4.17 4.18 The belt is located under the bottom plate of the vacuum and should be checked from brushroll. How To Replace Place handle in good condition. ...Rotate the latches (A) on either side of agitator into position by aligning tabs along front edge of cleaner. Discard used belt. To reduce the risk of the belt and positioned as shown with a Phillips ...To check the damaged belt, refer to Buy Use only genuine HOOVER® belts with bearings which contain sufficient lubrication for Belt HOOVER® part No. 562535001. 4.21 Place the bottom plate ...
...before servicing. 4.17 4.18 The belt is located under the bottom plate of the vacuum and should be checked from brushroll. How To Replace Place handle in good condition. ...Rotate the latches (A) on either side of agitator into position by aligning tabs along front edge of cleaner. Discard used belt. To reduce the risk of the belt and positioned as shown with a Phillips ...To check the damaged belt, refer to Buy Use only genuine HOOVER® belts with bearings which contain sufficient lubrication for Belt HOOVER® part No. 562535001. 4.21 Place the bottom plate ...
Product Manual
Page 30
... HEPA filter for 30 minutes, the thermal protector will stop running. SERVICE To obtain approved Hoover® service and genuine Hoover® parts, locate the nearest Authorized Hoover® Warranty Service Dealer (Depot) by: &KHFNLQJWKH When cleaner is unplugged and motor has cooled for any obstructions. When the thermal protector activates the...
... HEPA filter for 30 minutes, the thermal protector will stop running. SERVICE To obtain approved Hoover® service and genuine Hoover® parts, locate the nearest Authorized Hoover® Warranty Service Dealer (Depot) by: &KHFNLQJWKH When cleaner is unplugged and motor has cooled for any obstructions. When the thermal protector activates the...