Hoover H3044 Support and Manuals
Get Help and Manuals for this Hoover item
View All Support Options Below
Free Hoover H3044 manuals!
Problems with Hoover H3044?
Ask a Question
Free Hoover H3044 manuals!
Problems with Hoover H3044?
Ask a Question
Most Recent Hoover H3044 Questions
Brush Replacement
looking for a replacement brush for Hoover Floormate H3044. Haven't been able to locate or find a re...
looking for a replacement brush for Hoover Floormate H3044. Haven't been able to locate or find a re...
(Posted by mlgz007 1 year ago)
Popular Hoover H3044 Manual Pages
Manual - Page 2
... handle plug or appliance with the appliance - NOT for its intended use on carpets.
• Connect to a Hoover Sales and Service Center or Authorized Hoover Warranty Service Dealer.
• Always disconnect cord from openings and moving parts. • Do not pick up hard, sharp objects with this machine. Do not expose machine to whether the outlet is...
Manual - Page 3
... to this manual. Hard floor cleaner B. Floor cleaning
concentrate *Some models include a second set of brushes (gray bristles) for warranty service of your cleaner. Proof of date of the cleaner body.
our Consumer
Response Center, Mon-Fri 8am - 7pm EST
Fill in the spaces provided. To contact us:
• hoover.com • 1-800-944-9200 - automated service
dealer locator •...
Manual - Page 4
... 19. Bumper 15. Carrying handle 17. Cleaner Description
1 2
1
3
This cleaner is intended for wet pickup and dry vacuuming 5. Soft-tread wheels 16. Nozzle 13. Upper handle release button 18.
Features
1. ON/OFF switch 3. Clean solution tank 7. Mode selector dial: turns brushes
ON for wet cleaning and OFF for household use. Operate cleaner only at voltage specified on data plate...
Manual - Page 5
... upper handle (C) all the way down until you hear it rests on the floor.
Tilt cleaner back so
that it snap in upright position. Install brushes and nozzle
5
To install brushes, place handle in
place. Assemble handle
2
Rotate bottom handle support (A) up to the upright position until a
snap is felt.
3
Align control rod (B) on upper handle (C) with...
Manual - Page 8
..., bare wood or separated joints. General operation
Your HOOVER FloorMate™ SpinScrub™ Cleaner can be used to wood floors, follow the flooring manufacturer's cleaning recommendations. Refer to "How to the DRY VAC position. Mode selector dial
15
A
15
The Mode selector dial (A) turns the brushes on sealed wood floors, inspect floor surface for complete cleaning instructions.
8
Manual - Page 9
... wood, polyurethane sealed wood or other tiles, some models include a set of HOOVER® Grout Cleaner*.
*Available at additional cost if not included with gray bristles. Use these conditions could lead to damaged flooring when using water, use one
A
cup (2 oz.) HOOVER® Floor to Floor™ Cleaner. How to fill
Disconnect cleaner from electrical outlet. Carry tank to a sink...
Manual - Page 10
... snaps in Hoover SteamVac™ products. CAUTION: HOOVER® Grout Cleaner* cannot be locked in place.
formance and to fill line (C) (1 quart) with uneven side against ledge (E) as
D
shown.
22
22
Replace cap. Doing so could damage your SteamVac™ Cleaner. *Available at additional cost if not included with your model.
20
B
C
20
Pour cleaning concentrate into...
Manual - Page 12
... in place.
29
29
To replace recovery tank, place bottom of the floor surface.
30
The Mode selector dial turns the brushes on the filter screen
28
located in lid.
Remove debris from the lid. E
How to clean
Recommended cleaning sequence
Use your HOOVER® FloorMate™ SpinScrub™ Cleaner to:
• Dry Vacuum to the WET PICKUP position (C).
12 The...
Manual - Page 13
....
Note: When switching between the two settings.
10
Empty recovery tank or clean the filter when the motor sound becomes higher in your model. CAUTION: To prevent damage to pick up the dirty solution throughout
A
cleaning.
8
To greatly enhance drying of brushes to DRY VAC position and vacuum floor.
Continue to move cleaner forward and backward over the area to...
Manual - Page 15
bly of nozzle with opening (F) on cleaner.
Align middle section (E) of the nozzle. D
36
While holding nozzle in place, slide latches inward to lock in the upright position for easier assem- 35
F
DE
36
35 To replace nozzle, make sure latches (D) are out.
Cleaner should be in place.
15
Manual - Page 16
... in the upright position. Set aside.
37 Pull the two nozzle release buttons (A) out. The brushes can be washed with hole (D) on bottom of nozzle with opening (G) on cleaner. Do not use a solvent based detergent.
39
To replace brushes, align post (C) on floor.
38
Push two brush release buttons (B) and remove the brush assembly. Replace nozzle, making sure latches...
Manual - Page 17
...set for WET PICKUP. Make sure recovery tank is installed
properly. Empty recovery tank. Make sure filter and filter lid are properly
positioned. Check Model selector dial to ensure it is
set for DRY VAC. Tip nozzle off floor...the brushes continue to stall and the breaker trips again, clean the brushes to help solve minor problems.
What's the problem? Troubleshooting
Use the list below...
Manual - Page 18
... obtain approved HOOVER service and genuine HOOVER parts, locate the nearest Hoover Sales and Service Center or Authorized Hoover Warranty Service Dealer (Depot) by the complete model number when requesting information or ordering parts. (The model number appears on the back of Hoover on-line at hoover.com OR Checking the Yellow Pages under "Vacuum Cleaners - only) Do not send your cleaner by...
Manual - Page 19
... in the U.S.A., phone 1-800-944-9200 OR visit Hoover on-line at no cost to you, all labor and parts to place this warranty gives you specific legal rights, you mail your appliance to one way.
Warranty service can only be paid one of warranty service outlets, write or phone the Consumer Response Center, Phone...
Manual - Page 44
HOOVER y
son marcas registradas
HOOVER et
sont des marques déposées
HOOVER and
are registered trademarks
R5 7/07 H3030,H3032,H3040,H3044,H3045,H3030-050
Printed in China
59178-466
Hoover H3044 Reviews
We have not received any reviews for Hoover yet.