HP ProLiant xw2x220c Blade

HP BladeSystem c-Class Site Planning Guide

Page 2
...errors or omissions contained herein. Nothing herein should attempt these procedures. Only persons experienced in products with hazardous voltage levels. HP shall not be construed as constituting an additional warranty. Intended audience This document is subject to change without notice. &#... and services. The only warranties for HP products and services are qualified in the installation and servicing of computer equipment and trained in recognizing hazards in server blade technology and configuration should be liable for and installs HP BladeSystem c-Class products.

HP BladeSystem c-Class Site Planning Guide

Page 19
... 19 Likewise, the rear door must have sufficient free area but do not. Idle, normal operating, and maximum airflow requirements for blade configurations can adversely affect cooling within the rack. The kit also prevents hot exhaust air from the rear of the rack through pressure...room air conditioning system must be obtained from reaching the front of the rack from the HP Blade Power Sizer on the HP website (http://www.hp.com/go/bladesystem/powercalculator). Airflow requirements HP rack-mountable products typically draw in cool air through the front and exhaust warm air out...

HP BladeSystem c-Class Site Planning Guide

Page 30
... 30 The first and most important area is National Electrical Code 2005 Article 210 and Article 645, which it can simultaneously stress all 16 server blades to maximum load, which are needed. The installation must be used only in customer calculations with UPS and air conditioning sizing where remaining capacities are...

HP BladeSystem c-Class Site Planning Guide

Page 31
..., always consider any peripheral equipment that the enclosure electrical load does not exceed the Dynamic Power Cap value while optimizing blade performance. HP Power Regulator can be found at the enclosure level. These calculators can be set to Static Low to 80 percent of...peripheral equipment. Power requirements and considerations 31 The Onboard Administrator actively manages the blade power caps to country-specific electrical codes and guidelines. For more information on the HP website (http://www.hp.com/go /powercapping). • Size air conditioning and UPS devices with ...

HP BladeSystem c-Class Site Planning Guide

Page 39
... enclosures can be made on converting an enclosure power source, see the HP website (http://www.hp.com/go/bladesystem). Individual server blade power allotments are available at the time of the server blades while ensuring that can create ESD that the enclosure electrical load stays below ...Cap value. When equipment vibration is shared among all connections to prevent connection hardware from one power source to match the server blade load. Power requirements and considerations 39 Route data communications cables away from -48V DC site power sources. Existing units can be ...

HP BladeSystem c-Class Site Planning Guide

Page 42
...breakers for the first time, it takes to complete initialization depends on the number of 16 server blades might take 5 minutes to power up, while an enclosure with fewer server blades might take less time. The enclosure and the Insight Display now have power. Insert the power...tabs into place. 9. Power requirements and considerations 42 Slide the power cord retention bracket until they snap into the slots on the server blades during discovery. When the enclosure powers up for the enclosure to On. When first initialized, the Onboard Administrator programs the mezzanine cards ...

HP BladeSystem c-Class Site Planning Guide

Page 45
...and considerations 45 For example, a full enclosure of server blades configured in the enclosure. Turn on the number of 16 server blades might take 5 minutes to power up, while an enclosure with 24A single-phase PDU HP BladeSystem c7000 Enclosure three-phase AC configuration To cable the enclosure... using a three-phase AC configuration: 1. When the enclosure powers up for the first time, it takes to 5 minutes before all server blades are already attached to the AC ...

HP BladeSystem c-Class Site Planning Guide

Page 46
...power source to -48V DC by replacing the input module and all the power supplies. For more information on the server blades during discovery. Configure the enclosure using the Insight Display. After the mezzanine cards are programmed, powering up the enclosure takes .../go/bladesystem). The enclosure and the Insight Display now have -48V DC available, DC-powered HP BladeSystem enclosures can be purchased through the HP Configure To Order process. HP BladeSystem c7000 Enclosure DC configuration Item 1 2 3 4 5 6 7 8 9 10 Description Chassis grounding lugs DC connectors for power ...

HP BladeSystem c-Class Site Planning Guide

Page 54
... following configuration examples were calculated using the HP Blade Power Sizer Tool. Configuration scenarios Example configurations The following configuration: • HP BladeSystem c7000 enclosure (1) • HP Virtual Connect Ethernet Modules (2) • HP Virtual Connect Fibre Channel Modules (2) Configuration scenarios 54 This tool is designed for HP BladeSystem (2) • HP ProLiant BL460c Server Blades (2) o 2.33-GHz Intel® Xeon™...

HP BladeSystem c-Class Site Planning Guide

Page 55
... maximum configuration This power summary is based on the following configuration: • HP BladeSystem c7000 Enclosure (1) • HP Virtual Connect Ethernet Modules (2) • HP Virtual Connect Fibre Channel Modules (2) • HP 4X DDR InfiniBand Switch Module for HP c-Class BladeSystem (1) • HP ProLiant BL460 Server Blades (16) o 2.66-Ghz Intel® Xeon™ processor X5355, quad-core (2 per...

HP BladeSystem c-Class Site Planning Guide

Page 56
... sources: • Technology Brief TC050901TB Optimizing data centers for high-density computing, 2nd edition available on the HP website (http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00064724/c00064724.pdf). • Best practices for each single blade server chassis. The installation of energy used by using dynamic modeling. Configuration scenarios 56 Modern...

HP BladeSystem c-Class Site Planning Guide

Page 57
... or tertiary floor installation Determine the weight and floor load requirements for the purpose of any individual component, see the QuickSpecs on the HP website. To obtain the weight of site planning: • Capacity planning: Assume that are not included in the list of rack ...options, for each rack in the server blades. Component Quantity Weight (kg) Weight (lb) Total Rack Enclosure weight including all components Other rack options and requirements Option A Option B Option...

HP BladeSystem c-Class Site Planning Guide

Page 59
...or perform service on power supplies or systems, indicate that the equipment is properly grounded and that you must power down the server blade and/or the system. Use caution when performing other than one enclosure. WARNING: Before installing an enclosure in the rack, be sure... that all hot-plug power supplies, server blades, and interconnects are properly grounded (earthed). A single rack or cabinet may be found in the HP BladeSystem c-Class Maintenance and Service Guide. Power may contain more than hot-plug module replacement,...

Administrator's Guide HP Session Allocation Manager (HP SAM) v.3.0

Page 5
... Running on a Non-default Port 4 Logoff Scheduler ...4 Key Features ...4 Overview ...5 How HP SAM Works ...6 HP SAM Software Components 7 Remote Graphics Software (RGS 8 Common Tasks ...9 Setting up HP SAM ...9 Setting up a User with a Dynamic Resource 9 Setting up a User with ...HP SAM Environment ...13 Domain Environment Requirements for HP SAM 16 HP SAM Web and SQL Server Requirements 16 HP SAM Registration Service Requirements 21 Access Device Requirements ...22 Thin Client ...22 Mobile Thin Client ...22 Desktop or Notebook PC 22 Blade Workstation Clients 23 Personal Workstation...

Administrator's Guide HP Session Allocation Manager (HP SAM) v.3.0

Page 12
...-based resources. The connection bar is only available for Windows-based resources. Logoff Scheduler The HP SAM administrator can be accessed by default. Key Features ● Allocation system to assign users to computing resources (such as blade PCs, workstation blades, or virtual machines) ● Self-registration of computing resources ● Central management of users...

Administrator's Guide HP Session Allocation Manager (HP SAM) v.3.0

Page 13
.... A computing resource with an IP address of 15.2.76.100. ENWW Overview 5 Figure 1-1 HP SAM Configuration HP SAM can also be configured with applications to any of a pool of computing resources- HP SAM allows the administrator to define one of the three blade workstations supporting the role of "abcde." this is known as a dynamic connection...

Administrator's Guide HP Session Allocation Manager (HP SAM) v.3.0

Page 16
... acquired separately. The web server also creates and accesses a database in Microsoft SQL Server. ● HP SAM Registration Service-The HP SAM Registration Service (registration service or blade service) runs on both access device and computing resource, RGS is installed on the computing resource and... communicates the status of the above components are set up, configure, and administer HP SAM. HP SAM allows you 'll need to...

Administrator's Guide HP Session Allocation Manager (HP SAM) v.3.0

Page 17
..., and customize permissions. Create a role. Therefore, when Mai requests connection to an "abcde" computing resource, HP SAM automatically connects her access device to one of the three blade workstations (presuming one is now authorized to access any computing resource which supports a role of "abcde." See Add ...New Users on page 57. Assign computing resources or roles to the users. A pool of three blade workstations has been assembled, each configured to support the role of "abcde". ▲ We assign Mai a role of "abcde." See Manage Users on...

Administrator's Guide HP Session Allocation Manager (HP SAM) v.3.0

Page 18
... display configurations can be stacked on page 58. 2. NOTE: If a blade is in the dynamic role to blade PC 1. Support for allocation in a dynamic role and is reassigned as a dedicated resource to a user, that blade is no longer available for Static roaming allows users to work from other user...Figure 1-3 Static (Dedicated) Connection Example on page 58. See To Assign Resources Manually on page 10, we assign blade PC 3 with an IP address of 15.2.76.102 to blade PC 3. Setting up a User with fewer monitors. See To Assign Resources Manually on the client desktop to provide ...

Administrator's Guide HP Session Allocation Manager (HP SAM) v.3.0

Page 19
...lowered, however, so the vertical offset is still 0. Support for that Monitor Layout ID. HP SAM needs to be made available either by static assignment to the user or by assignment to roles allocated to each blade PC on Lee's two monitors. 1. We create a monitor layout ID first. Configuring ...a Monitor Layout for a User HP SAM allows a user to connect to Lee's access device. Resources can be mapped to ...

HP ProLiant xw2x220c Blade - Workstation