Manual
Page 29
...a metal object like a screwdriver to remove the jumper cap from the jumper. Definition 1 Signal 1 2 GND - 29 - Pin No. Open: Normal Short: Clear CMOS Values • Always turn off your computer, be sure to touch the two pins for BIOS configurations). 16) CI (Chassis Intrusion Header) This motherboard provides... (select Load Optimized Defaults) or manually configure the BIOS settings (refer to factory defaults. Hardware Installation date information and BIOS configurations) and reset the CMOS values to Chapter 2, "BIOS Setup," for a few seconds. 15) CLR_CMOS (Clearing...
...a metal object like a screwdriver to remove the jumper cap from the jumper. Definition 1 Signal 1 2 GND - 29 - Pin No. Open: Normal Short: Clear CMOS Values • Always turn off your computer, be sure to touch the two pins for BIOS configurations). 16) CI (Chassis Intrusion Header) This motherboard provides... (select Load Optimized Defaults) or manually configure the BIOS settings (refer to factory defaults. Hardware Installation date information and BIOS configurations) and reset the CMOS values to Chapter 2, "BIOS Setup," for a few seconds. 15) CLR_CMOS (Clearing...
Manual
Page 31
...the default settings (unless you can press + in system's failure to the "Load Optimized Defaults" section in this occurs, try to clear the CMOS values and reset the board to default values. (Refer to boot. If this chapter or introductions of the system in the... operating system, etc. To see more advanced BIOS Setup menu options, you need to) to keep the configuration values in the CMOS on . To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility. • Q-Flash allows the user to activate certain system features. Refer to Chapter 5, "Troubleshooting," for...
...the default settings (unless you can press + in system's failure to the "Load Optimized Defaults" section in this occurs, try to clear the CMOS values and reset the board to default values. (Refer to boot. If this chapter or introductions of the system in the... operating system, etc. To see more advanced BIOS Setup menu options, you need to) to keep the configuration values in the CMOS on . To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility. • Q-Flash allows the user to activate certain system features. Refer to Chapter 5, "Troubleshooting," for...
Manual
Page 46
.../140oF, 70oC/158oF, 80oC/ 176oF, 90oC/194oF. CPU/SYSTEM FAN Fail Warning Allows the system to run at full speed. (Default: Enabled) GA-G31M-ES2L/ES2C Motherboard - 46 - Check the fan condition or fan connection when this field will show "Yes", otherwise it will emit warning sound. If the... temperature. Current CPU/SYSTEM FAN Speed (RPM) Displays current CPU/system fan speed. 2-8 PC Health Status CMOS Setup Utility-Copyright (C) 1984-2009 Award Software PC Health Status Reset Case Open Status Case Opened Vcore DDR18V +3.3V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM ...
.../140oF, 70oC/158oF, 80oC/ 176oF, 90oC/194oF. CPU/SYSTEM FAN Fail Warning Allows the system to run at full speed. (Default: Enabled) GA-G31M-ES2L/ES2C Motherboard - 46 - Check the fan condition or fan connection when this field will show "Yes", otherwise it will emit warning sound. If the... temperature. Current CPU/SYSTEM FAN Speed (RPM) Displays current CPU/system fan speed. 2-8 PC Health Status CMOS Setup Utility-Copyright (C) 1984-2009 Award Software PC Health Status Reset Case Open Status Case Opened Vcore DDR18V +3.3V +12V Current CPU Temperature Current CPU FAN Speed Current SYSTEM ...
Manual
Page 47
...graphics chip and memory. mode based on your system fails to boot after overclocking, please wait for automated system reboot, or clear the CMOS values to reset the board to default values. (Default: Disabled) (Note) This item appears only if you install a CPU that you not to alter...instability or other unexpected results. (Inadequately altering the settings may result in red, it is recommended that supports this occurs, clear the CMOS values and reset the board to default values.) • When the System Voltage Optimized item blinks in damage to CPU, chipset, or memory and reduce...
...graphics chip and memory. mode based on your system fails to boot after overclocking, please wait for automated system reboot, or clear the CMOS values to reset the board to default values. (Default: Disabled) (Note) This item appears only if you install a CPU that you not to alter...instability or other unexpected results. (Inadequately altering the settings may result in red, it is recommended that supports this occurs, clear the CMOS values and reset the board to default values.) • When the System Voltage Optimized item blinks in damage to CPU, chipset, or memory and reduce...