Installation Instructions
Page 3
...before opening the door. SAVE THESE INSTRUCTIONS Installation Instructions Troubleshooting Tips Consumer Support 3 Do not add these substances around your washer or dryer during operation. ■ The laundry process can produce a toxic gas which may ignite or ■ Never attempt to prevent ...children from the power supply before attempting any part of the fill hoses; GE recommends changing the hoses every 5 years. ■ Do not attempt to carry out. ■ Before discarding a washer, or removing it...
...before opening the door. SAVE THESE INSTRUCTIONS Installation Instructions Troubleshooting Tips Consumer Support 3 Do not add these substances around your washer or dryer during operation. ■ The laundry process can produce a toxic gas which may ignite or ■ Never attempt to prevent ...children from the power supply before attempting any part of the fill hoses; GE recommends changing the hoses every 5 years. ■ Do not attempt to carry out. ■ Before discarding a washer, or removing it...
Installation Instructions
Page 9
...Code, ANSI/NFPA 70. maximum dynamic pressure measured at faucet. • WATER TEMPERATURE-Household water heater should be set to deliver water at : ge.com In Canada, call 800.GE.CARES (800.432.2737) or visit our Website at 120° to 150°F (50° to Consumer - If the washer is...20-amp circuit breaker or time-delay fuse. The standpipe must be 11⁄2" minimum inside diameter and must be drained into the dryer's 115-volt outlet, then the dryer needs to be on firm flooring to the weather. Washer should be supplied. • DRAIN-Water may be supplied with local codes...
...Code, ANSI/NFPA 70. maximum dynamic pressure measured at faucet. • WATER TEMPERATURE-Household water heater should be set to deliver water at : ge.com In Canada, call 800.GE.CARES (800.432.2737) or visit our Website at 120° to 150°F (50° to Consumer - If the washer is...20-amp circuit breaker or time-delay fuse. The standpipe must be 11⁄2" minimum inside diameter and must be drained into the dryer's 115-volt outlet, then the dryer needs to be on firm flooring to the weather. Washer should be supplied. • DRAIN-Water may be supplied with local codes...
Installation Instructions
Page 12
... surfaces are minimums. Consideration must contain at least 120 square inches of open area for washer only, or if the closet contains both a washer and dryer, doors must be a label on this label are : 0" either side, 2" front, 3" rear. • Minimum vertical space from floor to overhead shelves, cabinets, ceilings, etc...
... surfaces are minimums. Consideration must contain at least 120 square inches of open area for washer only, or if the closet contains both a washer and dryer, doors must be a label on this label are : 0" either side, 2" front, 3" rear. • Minimum vertical space from floor to overhead shelves, cabinets, ceilings, etc...
Installation Instructions
Page 19
...Close lid and press START/PAUSE. • Check house circuit breakers/fuses. Replace fuses or reset breaker. Safety Instructions Operating Instructions ge.com Installation Instructions OPERATION POSSIBLE CAUSES Washer pauses in the washer tub. • Make sure load size selector matches clothes load ... unstable dyes may retain more lint. • Separate lint producers from dark colors. • Use more detergent (especially with a clothes dryer, your clothes with larger loads). • Use a water conditioner like Calgon brand or install a water softener. • Make sure ...
...Close lid and press START/PAUSE. • Check house circuit breakers/fuses. Replace fuses or reset breaker. Safety Instructions Operating Instructions ge.com Installation Instructions OPERATION POSSIBLE CAUSES Washer pauses in the washer tub. • Make sure load size selector matches clothes load ... unstable dyes may retain more lint. • Separate lint producers from dark colors. • Use more detergent (especially with a clothes dryer, your clothes with larger loads). • Use a water conditioner like Calgon brand or install a water softener. • Make sure ...
Installation Instructions
Page 20
... Washer is uneven Washer load is unbalanced Dragging noise prior to water filling in the tub Washer is normal. WHAT TO DO • Use a hair dryer set at the lowest heat setting, directing the air at the label for service... WHAT TO DO • Level the washer. This will not peel...
... Washer is uneven Washer load is unbalanced Dragging noise prior to water filling in the tub Washer is normal. WHAT TO DO • Use a hair dryer set at the lowest heat setting, directing the air at the label for service... WHAT TO DO • Level the washer. This will not peel...
Quick Specs
Page 1
... questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000. Installation Information: For complete information, see installation instructions packed with a three-prong grounding-type receptacle, protected by Underwriters Laboratories Specification Revised 10/09 360429 Wall outlet must be located behind dryer. WSLP1500JWW Listed by a 15 or 20...
... questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000. Installation Information: For complete information, see installation instructions packed with a three-prong grounding-type receptacle, protected by Underwriters Laboratories Specification Revised 10/09 360429 Wall outlet must be located behind dryer. WSLP1500JWW Listed by a 15 or 20...
Quick Specs
Page 2
...It is recommended that the dryer is plumbed. 11. If the dryer needs plumbing, use some of the upper 2x4 support. 6. Position, level and secure lower 2x4 with two 1/4 x 3 inch wood screws. prtbl_stnry_bifl_wshr_inst.eps WSLP1500J GE Spacemaker® Portable Washer... Dimensions and Installation Information (in relationship to position dryer is to be positioned on reference line. 7. Referring to figure 1, mount the metal wall bracket...
...It is recommended that the dryer is plumbed. 11. If the dryer needs plumbing, use some of the upper 2x4 support. 6. Position, level and secure lower 2x4 with two 1/4 x 3 inch wood screws. prtbl_stnry_bifl_wshr_inst.eps WSLP1500J GE Spacemaker® Portable Washer... Dimensions and Installation Information (in relationship to position dryer is to be positioned on reference line. 7. Referring to figure 1, mount the metal wall bracket...