8511858 - FX-Series Hardware Reference Guide (for Windows Vista)
Page 42
...your computer has been configured. To prepare your computer for RAID Setting up RAID on how your computer for RAID: 1 Configure the RAID arrays. The BIOS Setup utility opens. 3 Select the Advanced menu, then select Drive Configuration. 4 Change the ATA/IDE Mode to Enhanced. 5 Change the SATA mode to ... capacity of the smallest drive × 2. Now that RAID is enabled, you have four drives (350 GB, 300 GB, 250 GB, and 200 GB) in a RAID 10 array, your computer turns on and the Gateway logo appears on page 36. 2 Install the operating system. RAID 10 treats the entire array as a ...
...your computer has been configured. To prepare your computer for RAID Setting up RAID on how your computer for RAID: 1 Configure the RAID arrays. The BIOS Setup utility opens. 3 Select the Advanced menu, then select Drive Configuration. 4 Change the ATA/IDE Mode to Enhanced. 5 Change the SATA mode to ... capacity of the smallest drive × 2. Now that RAID is enabled, you have four drives (350 GB, 300 GB, 250 GB, and 200 GB) in a RAID 10 array, your computer turns on and the Gateway logo appears on page 36. 2 Install the operating system. RAID 10 treats the entire array as a ...
8511858 - FX-Series Hardware Reference Guide (for Windows Vista)
Page 46
... on the system board. Overclocking may result in "Preventing static electricity discharge" on page 44. 4 Open the side panel and locate the jumper labeled J3C2 BIOS Config on the Gateway Technical Support Web site (support.gateway.com) and the Intel Support & Downloads Web site (support.intel.com). J3C2...
... on the system board. Overclocking may result in "Preventing static electricity discharge" on page 44. 4 Open the side panel and locate the jumper labeled J3C2 BIOS Config on the Gateway Technical Support Web site (support.gateway.com) and the Intel Support & Downloads Web site (support.intel.com). J3C2...
8511858 - FX-Series Hardware Reference Guide (for Windows Vista)
Page 47
The BIOS Setup utility opens. 8 Press the arrow keys to accept the changes. Setting up multiple monitors To set up multiple monitors, see...bridging pins 1-2). 14 Close the computer case. 15 Reconnect the power cord. 16 Turn the computer on your computer should start normally. www.gateway.com 5 Remove the jumper from its normal position (bridging pins 1-2), then place it in Normal mode position." 11 Turn off power and ... ENTER. 9 Press the - (minus) or + (plus) key repeatedly to adjust the multiplier, then press ENTER. 10 Press F10 to exit BIOS, then press Y to select the Performance tab.
The BIOS Setup utility opens. 8 Press the arrow keys to accept the changes. Setting up multiple monitors To set up multiple monitors, see...bridging pins 1-2). 14 Close the computer case. 15 Reconnect the power cord. 16 Turn the computer on your computer should start normally. www.gateway.com 5 Remove the jumper from its normal position (bridging pins 1-2), then place it in Normal mode position." 11 Turn off power and ... ENTER. 9 Press the - (minus) or + (plus) key repeatedly to adjust the multiplier, then press ENTER. 10 Press F10 to exit BIOS, then press Y to select the Performance tab.
8511858 - FX-Series Hardware Reference Guide (for Windows Vista)
Page 57
...of explosion if battery is displayed. The main menu of the same size and voltage as the original battery that was in your computer. www.gateway.com 7 Replace the side panel by following the instructions in "Removing the side panel" on a towel or other non-abrasive surface. 51...computer is incorrectly replaced. Windows starts and the Windows desktop appears. 10 Click (Start), right-click Computer, then click Properties. Use a battery of the BIOS Setup utility opens. 3 Write down all the values in the menus and submenus, then exit from the utility. 4 Shut down your computer. 5 ...
...of explosion if battery is displayed. The main menu of the same size and voltage as the original battery that was in your computer. www.gateway.com 7 Replace the side panel by following the instructions in "Removing the side panel" on a towel or other non-abrasive surface. 51...computer is incorrectly replaced. Windows starts and the Windows desktop appears. 10 Click (Start), right-click Computer, then click Properties. Use a battery of the BIOS Setup utility opens. 3 Write down all the values in the menus and submenus, then exit from the utility. 4 Shut down your computer. 5 ...
8511858 - FX-Series Hardware Reference Guide (for Windows Vista)
Page 58
Battery 8 Push the battery release tab. CHAPTER 1: Upgrading Your Computer 7 Locate the old battery on your computer. 14 Open the BIOS Setup utility. 15 In the BIOS Setup utility, restore any settings that you wrote down in "Replacing the side panel" on page 48. 12 Reconnect all external cables and the power ... the new battery is facing up, then press the battery into the socket until it snaps into place. 10 Return your settings and exit the BIOS Setup utility. 52 You will need to its upright position. 11 Replace the side panel by following the instructions in Step 3. 16 Save all your...
Battery 8 Push the battery release tab. CHAPTER 1: Upgrading Your Computer 7 Locate the old battery on your computer. 14 Open the BIOS Setup utility. 15 In the BIOS Setup utility, restore any settings that you wrote down in "Replacing the side panel" on page 48. 12 Reconnect all external cables and the power ... the new battery is facing up, then press the battery into the socket until it snaps into place. 10 Return your settings and exit the BIOS Setup utility. 52 You will need to its upright position. 11 Replace the side panel by following the instructions in Step 3. 16 Save all your...
8511858 - FX-Series Hardware Reference Guide (for Windows Vista)
Page 102
... up , then try again. • Try a different disc. For more information, see "Adjusting the volume" on page 81. • Restart your computer, then enter the BIOS Setup utility by the DVD drive. • Shut down and restart your online User Guide. . • Make sure that the mute controls are enabled. •...
... up , then try again. • Try a different disc. For more information, see "Adjusting the volume" on page 81. • Restart your computer, then enter the BIOS Setup utility by the DVD drive. • Shut down and restart your online User Guide. . • Make sure that the mute controls are enabled. •...