Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 20 Corepack Support and Manuals
Get Help and Manuals for this Garmin item
View All Support Options Below
Free Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 20 Corepack manuals!
Problems with Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 20 Corepack?
Ask a Question
Free Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 20 Corepack manuals!
Problems with Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 20 Corepack?
Ask a Question
Popular Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 20 Corepack Manual Pages
Flush Mount Template - Page 2
GMI™ 20 and GHC™ 20 Flush Mount Template
7/64 in. 2.8 mm
3 /17 32 in. 90 mm
April 2013
2 /23 64 in. 60 mm
190-01609-03_0A
Printed in Taiwan
Installation Instructions PDF - Page 1
... can consult the layout diagrams (Power and Data Layout, page 2) to operate the autopilot on your boat. Test any mounting hardware with the CCU. REACTOR™ 40 COMPACT HYDRAULIC
Installation Instructions
Important Safety Information
WARNING See the Important Safety and Product Information guide in the product box for product warnings and other than 1.5 m (5 ft.) to any...
Installation Instructions PDF - Page 3
... autopilot without a dedicated helm control, the autopilot CCU must be connected to the same NMEA 2000 network as a compatible Garmin chartplotter to the pump cannot be extended. You should install it to 24 Vdc power source. Pump
È
The pump must be located within 0.5 m (19 in the detailed installation instructions for planning purposes only. You should install a manual...
Installation Instructions PDF - Page 4
... 1/4 in the detailed installation instructions for easy pump disabling and removal, Garmin
recommends installing shut-off valves
Å
Helm
Æ
Steering cylinder
Ç
Dual-Helm Layout
Return line
À
Shadow Drive valve
Á
4 Important Considerations • The three hydraulic ports on all pipe threads in all autopilot packages. If needed, specific connection diagrams are not...
Installation Instructions PDF - Page 5
... network as indicated in place as a compatible Garmin chartplotter to avoid magnetic interference with a handheld compass to the boat battery, if possible. Detailed mounting instructions are present in . (20.3 cm) Up to the mounting
surface.
In addition, connecting the power cable without a dedicated helm control, the autopilot CCU must be extended (Power Cable Extensions...
Installation Instructions PDF - Page 6
... the port or starboard hydraulic line between the helm and the steering cylinder. If you install the autopilot without a dedicated helm control, the autopilot CCU must be connected to the same NMEA 2000 network as a compatible Garmin chartplotter to the mounting surface using the pump as a template. 2 Using a drill bit appropriate for manual steering. Item
Description...
Installation Instructions PDF - Page 8
... the installation instructions for the NMEA 0183 device to identify the transmit (TX) and receive (RX) wires. • The device provides one TX port and one internal NMEA 0183 output port (TX port) on the helm control or a compatible Garmin chartplotter to your chartplotter for more -specific information about bleeding the system. Solder all autopilot...
Configuration Guide PDF - Page 1
..., provide rudder-movement clearance to avoid damage to configure the autopilot. REACTOR™ 40 HYDRAULIC
Configuration Guide
Important Safety Information
WARNING See the Important Safety and Product Information guide in the opposite direction,
on a chartplotter, select Switch Direction, and repeat steps 1 though 3.
Instructions for product warnings and other important information. If the...
Configuration Guide PDF - Page 2
... do not move around on -screen instructions.
2 NMEA 2000 or GPS, configure... not align, there may be a problem with the speed source set to GPS, configure the maximum speed....Settings > My Vessel > Autopilot Installation Setup > Compass Setup > Compass Cal. > Begin.
2 Follow the directions until calibration is complete, taking care to keep the boat as steady and flat as possible. NOTE: Garmin...
Configuration Guide PDF - Page 3
... oscillate slightly, but it makes turns. When you manually adjust the acceleration limiter, make relatively small adjustments.
Adjusting the Acceleration Limiter Settings 1 On a helm control, enable Dealer Mode (Enabling Dealer
Configuration on a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Compass Setup > Fine Heading Adjustment > Begin.
2 Adjust the fine...
Configuration Guide PDF - Page 4
...Select Back > Back. Manually Defining Individual Configuration Settings Configuring certain configuration settings may be multiple sources of Sensor Information 1 Select an option:
• On a helm control, from the heading screen, select Menu > Setup > Dealer Autopilot Setup.
• On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Autopilot Tuning.
3 Select an...
Configuration Guide PDF - Page 5
... transitions from displacement to adjust how tightly the rudder
corrects turn rate. On a chartplotter, select Settings > My Vessel > Autopilot Installation Setup > Autopilot Tuning. controlled turns. Speed Source: Allows you to planing speed. Planing RPM: Allows you can manually adjust any setting to adjust the RPM reading on the dashboard of your boat. If the value does not...
Owners Manual - Page 7
... the installation instructions included with the Autopilot You can steer the boat according to a route defined on a compatible GPS device. 1 Create and navigate a route on a GPS waypoint to which the autopilot turns your GPS device. 2 Select Menu > GPS Steering > Follow Route. Sailboat Autopilot Operation
3 Cancelling a Steering Pattern • Physically steer the boat. CAUTION Garmin®...
Owners Manual - Page 8
... pairing the remote control according to the instructions
that you assign a pattern to the helm control. Pairing a Remote 1 Search for a remote control (Searching for Remote.
For day color mode, you from manually performing a gybe using the helm or step steering. System Settings
Select Menu > Setup > System.
Adjusting the Autopilot Response
When in sailboat mode, the...
Owners Manual - Page 9
GHC Low Volt. System Information: Allows you to set the operating mode to
normal or store demo mode. If a third-party GPS compass is unavailable, the autopilot screen does not display ...specified level. The autopilot needs timely information, and therefore cannot often use a Garmin sensor for GPS location or speed. If the selected heading source is used, the autopilot will likely report ...
Garmin Compact Reactor 40 Hydraulic Autopilot with GHC 20 Corepack Reviews
We have not received any reviews for Garmin yet.