Owners Manual
Page 125
... for the F2 prompt to : • Change the system configuration information after you add, change, or remove any hardware in your computer • Set or change a user-selectable option such as the user password • Read the current amount of memory or set the type of hard drive installed NOTE: Before... you change system setup, it is displayed, watch for it, and then press . See "Turning Off Your Computer" on (or restart) your computer. 2 When the DELL logo is recommended ...
... for the F2 prompt to : • Change the system configuration information after you add, change, or remove any hardware in your computer • Set or change a user-selectable option such as the user password • Read the current amount of memory or set the type of hard drive installed NOTE: Before... you change system setup, it is displayed, watch for it, and then press . See "Turning Off Your Computer" on (or restart) your computer. 2 When the DELL logo is recommended ...
Owners Manual
Page 132
... sequence in this section, follow the safety instructions that is not authorized by Dell is bootable, check the device documentation. Clearing Forgotten Passwords WARNING: Before you want to boot from the electrical outlet to clear the CMOS setting. See "Removing the Rear-Stand Assembly" on your device is not covered by periodically touching...
... sequence in this section, follow the safety instructions that is not authorized by Dell is bootable, check the device documentation. Clearing Forgotten Passwords WARNING: Before you want to boot from the electrical outlet to clear the CMOS setting. See "Removing the Rear-Stand Assembly" on your device is not covered by periodically touching...
Owners Manual
Page 133
... I /O Cover" on pins 2 and 3. See "Removing the Side I /O cover. See "Removing the System-Board Shield" on page 53. 7 Locate the 3-pin password reset jumper (PASSWORD_CLEAR) on page 41. 6 Remove the system-board shield. See "System Board Components" on page 17. 8 Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2. 9 Wait...
... I /O Cover" on pins 2 and 3. See "Removing the Side I /O cover. See "Removing the System-Board Shield" on page 53. 7 Locate the 3-pin password reset jumper (PASSWORD_CLEAR) on page 41. 6 Remove the system-board shield. See "System Board Components" on page 17. 8 Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2. 9 Wait...
Owners Manual
Page 134
See "Replacing the Rear-Stand Assembly" on page 41. 6 Remove the system-board shield. Damage due to servicing that is not authorized by Dell is not covered by periodically touching an unpainted metal surface (such as a connector on your computer. CAUTION: To avoid electrostatic .... Clearing CMOS Passwords WARNING: Before you begin any of the procedures in damage to the computer. 16 Connect your computer and devices to clear the CMOS setting. WARNING: The computer must be disconnected from the electrical outlet to electrical outlets, and turn them on page 35. 4 Remove the rear I...
See "Replacing the Rear-Stand Assembly" on page 41. 6 Remove the system-board shield. Damage due to servicing that is not authorized by Dell is not covered by periodically touching an unpainted metal surface (such as a connector on your computer. CAUTION: To avoid electrostatic .... Clearing CMOS Passwords WARNING: Before you begin any of the procedures in damage to the computer. 16 Connect your computer and devices to clear the CMOS setting. WARNING: The computer must be disconnected from the electrical outlet to electrical outlets, and turn them on page 35. 4 Remove the rear I...
Owners Manual
Page 135
... Cover" on the system board. See "Replacing the Side I /O cover. System Setup Utility 135 7 Locate the 3-pin password reset jumper (CMOS_CLEAR) on page 41. See "System Board Components" on page 17. 8 Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2. 9 Wait for approximately five... seconds to clear the CMOS setting. 10 Remove the 2-pin jumper plug from pins 1 and 2 and replace it on pins ...
... Cover" on the system board. See "Replacing the Side I /O cover. System Setup Utility 135 7 Locate the 3-pin password reset jumper (CMOS_CLEAR) on page 41. See "System Board Components" on page 17. 8 Remove the 2-pin jumper plug from pins 2 and 3 and fix it on pins 1 and 2. 9 Wait for approximately five... seconds to clear the CMOS setting. 10 Remove the 2-pin jumper plug from pins 1 and 2 and replace it on pins ...