Quick Installation Guide
Page 1
...modem 3. The following information about your new ADSL connection from your Internet Service Provider: TABLE 1 Parameter Connection Type Encapsulation VPI / VCI Security Protocol Username / password (PPP connections only) IP address / Subnet Mask / Default Gateway (Bridge connections only) DNS IP Addresses (optional) Tick your purchase of this DSL-302G... the modem to the PC before installing the software. Connecting modem to gather your broadband ADSL connection. Software installation 1.2. For any advanced features of the D-Link DSL-302G ADSL modem. DSL-302G ADSL Modem Quick ...
...modem 3. The following information about your new ADSL connection from your Internet Service Provider: TABLE 1 Parameter Connection Type Encapsulation VPI / VCI Security Protocol Username / password (PPP connections only) IP address / Subnet Mask / Default Gateway (Bridge connections only) DNS IP Addresses (optional) Tick your purchase of this DSL-302G... the modem to the PC before installing the software. Connecting modem to gather your broadband ADSL connection. Software installation 1.2. For any advanced features of the D-Link DSL-302G ADSL modem. DSL-302G ADSL Modem Quick ...
Quick Installation Guide
Page 7
... Explorer). of the Troubleshooting section at the end of this guide. 2. of the Troubleshooting section at the end of the modem in the address bar: • If you you are connecting through the USB port type: http://10.1.1.2 Press Enter and you connected the USB ... USB cable after finishing the software installation and rebooting the computer. * If you should be prompted to paragraph 3.1.1. The default username is admin and the password is admin: * If you are connecting through the Ethernet port type: http://10.1.1.1 • If you are not getting this prompt please refer to ...
... Explorer). of the Troubleshooting section at the end of this guide. 2. of the Troubleshooting section at the end of the modem in the address bar: • If you you are connecting through the USB port type: http://10.1.1.2 Press Enter and you connected the USB ... USB cable after finishing the software installation and rebooting the computer. * If you should be prompted to paragraph 3.1.1. The default username is admin and the password is admin: * If you are connecting through the Ethernet port type: http://10.1.1.1 • If you are not getting this prompt please refer to ...
Quick Installation Guide
Page 11
...password are correct; • Double-check the Security Protocol settings (PAP/CHAP) with your ISP Connection established • Reboot your computer and try accessing the Internet again • Try specifying IP address and DNS settings on your computer as described above More information on DSL-302G... can be found at http://www.dlink.com.au/products/broadband/dsl302g/ Technical support information on DSL-302G: http://www.dlink.com.au/tech/drivers/files/modems/dsl302g.htm D-Link Australia Technical Support can not access the Internet...
...password are correct; • Double-check the Security Protocol settings (PAP/CHAP) with your ISP Connection established • Reboot your computer and try accessing the Internet again • Try specifying IP address and DNS settings on your computer as described above More information on DSL-302G... can be found at http://www.dlink.com.au/products/broadband/dsl302g/ Technical support information on DSL-302G: http://www.dlink.com.au/tech/drivers/files/modems/dsl302g.htm D-Link Australia Technical Support can not access the Internet...
Installation Guide
Page 7
The new menu lists 8 channels available for only one channel in order to use the ADSL modem. You need to highlight it and press the Enter or Return key. Click on the first channel listed to change settings for configuration. Click Ok ... the default channel used by the modem. The default encapsulation method used (LLC or VC Mux) from the pull-down menu. Click Set Note: The default settings for the password. You should now be prompt for the modem are VPI of "0" and a VCI of the DSL-302G or highlight it , this information. Double-click on...
The new menu lists 8 channels available for only one channel in order to use the ADSL modem. You need to highlight it and press the Enter or Return key. Click on the first channel listed to change settings for configuration. Click Ok ... the default channel used by the modem. The default encapsulation method used (LLC or VC Mux) from the pull-down menu. Click Set Note: The default settings for the password. You should now be prompt for the modem are VPI of "0" and a VCI of the DSL-302G or highlight it , this information. Double-click on...