Cisco WS-X4624-SFP-E - Line Card Expansion Module Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-X4624-SFP-E manuals!
Problems with Cisco WS-X4624-SFP-E?
Ask a Question
Free Cisco WS-X4624-SFP-E manuals!
Problems with Cisco WS-X4624-SFP-E?
Ask a Question
Cisco WS-X4624-SFP-E Videos
Cisco WS-X4624-SFP-E= $7500 Price Reduction
Duration: :34
Total Views: 14
Duration: :34
Total Views: 14
Buy Cisco WS-X4624-SFP-E Price $4,899.00 - 3Anetwork.com
Duration: :31
Total Views: 4
Duration: :31
Total Views: 4
Cisco WS-X4624-SFP-E $7500 Price Reduction
Duration: :34
Total Views: 8
Duration: :34
Total Views: 8
Popular Cisco WS-X4624-SFP-E Manual Pages
Hardware Maintenance Manual - Page 2
...with the specifications in part 15 of the FCC rules. Network Time Protocol (NTP).
Cisco incorporates Fastmac software in a residential installation.
NOTWITHSTANDING ...manual are presented without notice. If it is a trademark of the Massachusetts Institute of Technology. All rights reserved.
The X Window System is not installed in accordance with Cisco's installation instructions...
Hardware Maintenance Manual - Page 3
... and potentially through the Sales or Service Partner, either (i) to the party that Cisco or its Sales Partner cannot reasonably reproduce the Software error, (6) has been exported from the date of Cisco. Cisco warrants that aspects of the licensed materials, including the specific design and structure of individual programs, constitute trade secrets and/or copyrighted material of...
Hardware Maintenance Manual - Page 4
... on a straight-line basis. This License is subject to the restrictions as described above warranty does not apply to either (i) provide advance replacement service as set forth in Cisco's recommended spares list. Cisco may terminate this Agreement.
Cisco warrants to Cisco or the Sales or Service Partner in material and workmanship. Hardware Remedies. In the event of the...
Hardware Maintenance Manual - Page 5
TABLE OF CONTENTS
About This Manual xv Document Objectives xv Audience xv Document Organization xv Document Conventions xvi
Chapter 1 Cisco 4000 Series Overview 1-1 External Differences in Models of the Cisco 4000 Series 1-1 Series Specifications 1-2 Memory Systems 1-4
Chapter 2 Preparing for Installation 2-1 Safety Recommendations 2-2 Safety with Electricity 2-2 Preventing Electrostatic Discharge...
Hardware Maintenance Manual - Page 15
... or call Customer Service. About This Manual xv
Document Objectives
This publication contains the initial site preparation, installation, troubleshooting, and selected upgrade and maintenance procedures. Document Organization
The major sections of the Cisco 4000 series features
and physical specifications.
• Chapter 2, "Preparing for Installation," includes safety recommendations...
Hardware Maintenance Manual - Page 16
...
overview, problem-solving instructions, environmental reporting features, and understanding front-panel and network-processor module LED indicators.
• Chapter 5, "Maintaining and Upgrading the Router," includes instructions for opening the
chassis, replacing or adding network processor modules, and replacing single in-line memory modules (SIMMs).
• Appendix A, "Cabling Specifications...
Hardware Maintenance Manual - Page 37
...lists the IEEE-recommended maximum speeds and distances for Installation...
50
15
Balanced drivers allow EIA/TIA-449 signals ...support synchronous connections, and the console and auxiliary ports support asynchronous connections. Network Connection Considerations
Serial Connections
When setting...25-pin D-shell connector known as EIA/... you understand the electrical problems that might arise and can...
Hardware Maintenance Manual - Page 43
... serial cable to connect the router to the software publications. To set , or if the cable is DCE and the clock rate is not configured. Figure 2-22 Dual Serial Network Processor Module Jumpers, J4 and J5-NRZI Setting
J5 J4
Pin 1
H1125a
Port 1
Port 0
You must be manually changed. See the appendix "Cabling Specifications."
Hardware Maintenance Manual - Page 52
... nF/km
Impedance (@ 96 kHz) 75 ohms
150 ohms
Wire diameter
0.024" (0.6 mm)
0.024" (0.6 mm)
Distance limitation
32.8' (10 m)
32.8' (10 m)
1. Network Connection Considerations
The specifications for the BRI cable are given in Figure 2-32, provides a controller for a remote site.
2-30 Cisco 4000 Series Hardware Installation and Maintenance
Hardware Maintenance Manual - Page 54
...120-ohm or 75-ohm. The figure shows the cable impedance set the cable impedance to a channel service unit (CSU). These jumpers set to 24 virtual channels. LOOPBACK LOCAL ALARM REMOTE ALARM H3154
Network Connection Considerations
Channelized E1 Connections
The Cisco 4000 series router supports a channelized E1 (CE1) network processor module with capacitive coupling between the...
Hardware Maintenance Manual - Page 55
... configured with BNC Connectors)
H2421
Preparing for Installation 2-33 Figure 2-36
E1 Interface Cable for injury, jumper J2 should be set to chassis ground.
All of these jumpers must be configured by trained service personnel only. This is a setting that could pose a risk of Jumpers on the network end. Warning To prevent problems with the E1...
Hardware Maintenance Manual - Page 58
...ATM processor module for the Cisco 4000 series router uses identical duplex SC connectors for shipping damage. This ...specific part number visible on the upper surface of the single-mode ATM products when no fiber-optic cable is not ready, keep the chassis in more than one container.
The router, cables, publications, and any optional equipment you encounter problems when installing...
Hardware Maintenance Manual - Page 123
... set the software configuration register (bits 3, 2, 1, and 0) to be off by entering configuration mode, and then entering the configuration command following command at the ROM monitor prompt (>) o enable the Break key and to default to the ROM monitor prompt. Cisco 4000-M ROM Monitor C-1 If you isolate or rule out hardware problems encountered when installing...
Hardware Maintenance Manual - Page 127
... options is powered-up or reset. The Cisco 4500-M and Cisco 4700 ROM monitor supports more features than the familiar Cisco 4000-M ROM monitor. If you set the software configuration register (bits 3, 2, 1, and 0) to zero, you isolate or rule out hardware problems encountered when installing your router. APPENDIX D
Cisco 4500-M and Cisco 4700 ROM Monitor
This appendix describes the...
Hardware Maintenance Manual - Page 141
...publications xv overview, series 1-1
P
packing list 2-36 pinouts
auxiliary port A-2 BRI ...specifications 1-3 supply features 2-4 system, troubleshooting 4-2 preparing for installation 2-1 to make connections 2-7 preventing ESD damage 2-3 preventive site configuration 2-4 printing summary of ROM monitor commands problem indications 4-3 temperature 4-3 problem solving 4-1 processor specifications...
Cisco WS-X4624-SFP-E Reviews
We have not received any reviews for Cisco yet.