Cisco WS-C2950SX-48-SI Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-C2950SX-48-SI manuals!
Problems with Cisco WS-C2950SX-48-SI?
Ask a Question
Free Cisco WS-C2950SX-48-SI manuals!
Problems with Cisco WS-C2950SX-48-SI?
Ask a Question
Popular Cisco WS-C2950SX-48-SI Manual Pages
Software Guide - Page 29
.../Directory/DirTAC.shtml
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
xxix You and Cisco will commit all customers who have a valid Cisco service contract have complete access to the technical support resources on the Cisco TAC website. Cisco TAC Escalation Center
The Cisco TAC Escalation Center addresses priority level...
Software Guide - Page 32
...full duplex • Optional redundant power supplies
Catalyst 2948G Switch
Note For installation information and a complete description of the Catalyst 2948G switch hardware, refer to the Catalyst 2948G and 2980G Installation Guide.
Table 1-2 Catalyst 2948G Switch
Product Number WS-C2948G
Chassis Description Catalyst 2948G • Fixed-configuration switch • 12-Gbps backplane •...
Software Guide - Page 177
... centrally on configuring VLANs, see Chapter 10, "Configuring VLANs."
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1 9-1 You can use VTP to manage VLANs 1-1005 in your network. (VTP version 1 and VTP version 2 do not support VLANs 1025-4094.) With VTP, you can result in this chapter, refer to...
Software Guide - Page 203
... shown in length Console> (enable)
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
9-27 Console> (enable) set VTP passwords, perform this task in the configuration instead of hiding the VTP password from the password is removed.
Console> (enable) set vtp passwd command that is generated from the configuration...
Software Guide - Page 222
...the promiscuous port.
10-16
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01 ...set of private VLAN ports are isolated at Layer 2 from all the community and isolated ports.
• An isolated port has complete Layer 2 separation, including broadcasts, from the same Catalyst 4500 series switch. The three types of supporting...
Software Guide - Page 260
...OC3 MMF ATM 10 BASE-T
12-8
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01
Console> (enable) set to VMPS table as backup domain ...trunk ports or secure ports a dynamic port. Console> (enable) set vmps server ip_addr
Verify the VMPS server specification.
Console> (enable) show port [mod_num[/port_num]]
This example ...
Software Guide - Page 298
...error is set to 12000 milliseconds. Command set garp timer {join | leave | leaveall} timer_value show gmrp statistics 23 GMRP Statistics for leaveall must be greater than three times the join value (leave >= join * 3).
Configuring GMRP
Chapter 15 Configuring Multicast Services
When you set...14
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-...
Software Guide - Page 300
... and verify the configuration (the asterisks indicate that the entry was manually configured):
Console> (enable) set multicast router mod_num/port_num show multicast group CGMP enabled IGMP disabled
15-16
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01 Console> (enable) show multicast group [mac_addr] [vlan_id]
This...
Software Guide - Page 378
...
Console> (enable) set snmp access-list 2 172.20.60.7 Access number 2 has been updated with new IP Address 172.20.60.7
Console> (enable) set snmp ifalias {ifIndex}... SNMP configuration:
Console> (enable) show snmp ifalias [ifIndex]
24-10
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01 Console> (enable)
Console> (enable) clear...
Software Guide - Page 423
...swap or other short-term emergency, because you can support the switch configuration. • When using variable power supplies, ...mode in the Catalyst 4500 series switches: • The two power supplies must be the same type.
Modules are set to redundant mode...PS2). Note If you set to combined mode and only one power supply is installed, your switch is set the power budget to ...
Software Guide - Page 429
... 2-port 1000BASE-X (GBIC) Gigabit Ethernet WS-4232-GB-RJ
48-port 100BASE-FX Fast Ethernet switching module WS-4148-FX-MT
18-port server switching 1000BASE-X (GBIC) Gigabit Ethernet WS-4418-GB
Catalyst 4006 Backplane Channel Module WS-X4019
48-port 10/100 Fast Ethernet RJ-45 WS-X4148-RJ
Catalyst 4003 and 4006 Layer 3 Services Module WS-X4232-L3
12-port 1000BASE...
Software Guide - Page 430
... you insert the supervisor engine into the Catalyst 4500 series chassis. The network designates a new root switch; the Catalyst 4500 series switches have 64 MAC addresses. The bridge ID priority of the root bridge after you replace the chassis with MAC reduction enabled and a default spanning tree bridge ID priority set to 32,768 to the network, the...
Software Guide - Page 457
...4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
30-13 You must reset the password after installing software release 5.4 or a later release to set the enable password on the switch:
Console> (enable) set enablepass Enter old password: Enter new password: Retype new password: Password changed .
Note Passwords that are set password Return on...
Software Guide - Page 459
... the set password or set localuser user picard password captain privilege 15
Added local user picard. Creating a Local User Account
Local user accounts and passwords must contain at least one alphabetic character. Step 2 Verify the local user account. picard
15
Console> (enable)
78-15486-01
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release...
Software Guide - Page 480
... forward
30-36
Catalyst 4500 Series, Catalyst 2948G, Catalyst 2980G Switches Software Configuration Guide-Release 8.1
78-15486-01
To configure clients to forward user credentials as they connect to other services on the network with Kerberized clients. For example, Telnet prompts for users to authenticate to other network services:
Console> (enable) set kerberos clients mandatory...
Cisco WS-C2950SX-48-SI Reviews
We have not received any reviews for Cisco yet.