Cisco NME-WAE-502-K9 - Wide Area Application Services Network Module Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco NME-WAE-502-K9 manuals!
Problems with Cisco NME-WAE-502-K9?
Ask a Question
Free Cisco NME-WAE-502-K9 manuals!
Problems with Cisco NME-WAE-502-K9?
Ask a Question
Popular Cisco NME-WAE-502-K9 Manual Pages
User Guide - Page 5
... are created the first time that maintains VLAN configuration consistency by software;
Only one SVI can be explicitly configured. Routed ports support only CEF switching (IP fast switching is a physical port that acts like a regular router interface, except that you wish to configure an SVI for the default VLAN (VLAN 1) to the VLAN tag associated...
User Guide - Page 50
For 802.1Q trunks, specifies the native VLAN.
(Optional) Configures the list of the default VLANs from a trunk. All VLANs are allowed by default.
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
50 Configures the interface as a Layer 2 trunk, use the description command in global configuration mode:
Step 1 Step 2
Step 3 Step 4 Step 5
Step 6 Step 7
Command
Router(config...
User Guide - Page 62
... on the same RADIUS server are configured for the same service-for 802.1x authentication.
To disable AAA, use the no aaa authentication dot1x {default | list-name} method1 [method2...] global configuration command.
The RADIUS host entries are identified by their host name or IP address, host name and specific UDP port numbers, or IP address...
User Guide - Page 65
...
Step 3 Step 4 Step 5
end show dot1x copy running -config startup-config
Purpose Enters global configuration mode. the default is 2. the default is 30. and 36-Port Ethernet Switch Module for a response to 65535 seconds; Sets the number of time that the switch waits for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Configuration Tasks
Note You should...
User Guide - Page 66
...-logoff message is set to be successfully authorized for a specific interface, use the show dot1x privileged EXEC command.
Allows multiple hosts (clients) on an 802.1x-authorized port that the dot1x port-control interface configuration command is received), all attached clients are indirectly attached. To disable multiple hosts on page 12.
Cisco IOS Release 12.2(2)XT...
User Guide - Page 81
..., and Cisco 3700 Series
Configuration Tasks
Supported parameters can be grouped into these categories: • TCP • UDP Table 12 lists the possible filtering parameters for ACEs for Cisco IOS Release 12.2. Table 12 Filtering Parameter ACEs Supported by Different IP Protocols
Filtering Parameter
TCP
UDP
Layer 3 Parameters: IP ToS byte1
No
No
Differentiated Services Code Point (DSCP...
User Guide - Page 85
... 1 Step 2
Step 3 Step 4
Command
Purpose
configure terminal
Enters global configuration mode. Beginning in }
end
Returns to have some remarks before reaching the end. The interface must be confusing to privileged EXEC mode.
Note these steps to control access to remove ACEs from an associated IP host address access list specification, 0.0.0.0 is assumed to 100 characters. After...
User Guide - Page 105
... or a specific interface.
Step 1 Step 2
Use the show storm-control command to display the count of global storm-control, use the following commands beginning in privileged EXEC mode:
Command
Purpose
show interface [interface-id] counters multicast Verifies the multicast suppression discard counter for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Configuration Tasks...
User Guide - Page 108
...Configuring a Single Subnet for the new Cisco IP phones, each of which requires a unique IP address.
• Administering a network with a VVID that there is physically the same. Layer 3 classification is already handled because the phone sets the Type of Service...deploy IP telephony.) When this marking changed to a Differentiated Services Code Point ([DSCP]) value of EF.) However, to provide...
User Guide - Page 159
... the Cisco IOS configuration file. The enable and line methods use the no authentication. aaa authentication dot1x {default | listname} method1 [method2...]
no aaa authentication dot1x {default | listname} method1 [method2...]
Syntax Description default
listname
method1 [method2...]
Uses the listed authentication methods that are saved in the given sequence to validate the password provided...
User Guide - Page 175
....1x-enabled port.
Cisco IOS Release 12.2(2)XT, 12.2(8)T, and 12.2(15)ZJ
175 Defaults
Multiple hosts are denied access to allow multiple hosts:
Switch(config)# interface fastethernet0/1 Switch(config-if)# dot1x port-control auto Switch(config-if)# dot1x multiple-hosts
You can verify your settings by entering the show dot1x
Description Enables manual control of the authorization...
User Guide - Page 180
... timeout quiet-period 30
You can verify your settings by entering the show dot1x
Description
Displays 802.1x statistics, administrative status, and operational status for the switch or for unusual circumstances such as unreliable links or specific behavioral problems with the client.
You should change the default value of this command.
dot1x timeout quiet-period...
User Guide - Page 196
....2(15)ZJ
Defaults
No match criteria are supported. Examples
The following example shows how to classify the packets. match {access-group acl-index-or-name}
no form of an IP standard or extended access control list (ACL).
This command was introduced.
Note For more information about configuring IP ACLs, refer to the "Configuring IP Services" chapter...
User Guide - Page 198
...port.
It replaced the switchport...Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers. To return to the default setting, use the no mls qos cos {default-cos | override}
Syntax Description default-cos override
Assigns a default CoS value to -Differentiated Services Code Point (DSCP) map.
This command was introduced.
mls qos cos
16- Command Modes Interface configuration...
User Guide - Page 207
... policy-map class configuration mode. You can configure up to six policers on the following platforms: Cisco 2600 series, Cisco 3600 series, and Cisco 3700 series routers. and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
police
police
To define a policer for classified traffic, use the end command. Defaults
No policers are...
Cisco NME-WAE-502-K9 Reviews
We have not received any reviews for Cisco yet.