Cisco NM-1HSSI - 3640/3620 Single Porthssi Network Module Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco NM-1HSSI manuals!
Problems with Cisco NM-1HSSI?
Ask a Question
Free Cisco NM-1HSSI manuals!
Problems with Cisco NM-1HSSI?
Ask a Question
Cisco NM-1HSSI Videos
CISCO NM-1HSSI $35 Price Reduction
Duration: :34
Total Views: 2
Duration: :34
Total Views: 2
Popular Cisco NM-1HSSI Manual Pages
User Guide - Page 2
...packet. This network module is a modular, high-density voice network module that provides Layer 2 switching across Ethernet ports.
An optional power module can be used as an uplink port to a server or as a stacking link to configure the 16- The 16-port Ethernet switch network module has 16 10/100BASE-TX ports and an optional 10/100/1000BASE-T Gigabit Ethernet port. Cisco IOS Release...
User Guide - Page 5
...in your network. Routed ports support only CEF switching (IP fast switching is a Layer 2 messaging protocol that can configure is a physical port that are deleting any Layer 3 characteristics configured on the device to route traffic, and assign it an IP address. VTP minimizes misconfigurations and configuration inconsistencies that maintains VLAN configuration consistency by using the...
User Guide - Page 7
... in secure mode.
• A VTP version 2-capable switch can use VTP in a VTP domain must run the same VTP version.
• You must configure a password on each EtherChannel must decide whether to a numerical value that VTP version 2 is disabled on the switch. A Ethernet switch network module system supports a maximum of the binary pattern formed from NVRAM.
User Guide - Page 29
... in an ACL must have different rules that use the same mask; All other combinations of system-defined masks. The Ethernet switch network module ACL configuration is allowed, but cannot be attached to certain types of user-defined mask is consistent with a destination TCP port number of service (QoS) can be shared by QoS and security...
User Guide - Page 31
... queues. and 36-Port Ethernet Switch Module for Layer 2 QoS on the dot1p value in your network can function as a Layer 2 switch connected to -end QoS solution.
The Ethernet switch network module can be serviced, it is based on the Ethernet switch network module. Table 6 summarizes the queues, CoS values, and weights for Cisco 2600 Series, Cisco 3600 Series, and...
User Guide - Page 33
... the map is a mechanism that you define the match criterion for Configuring ACLs on the Ethernet Switch Network Module" section on a specific traffic class by using the access-list global configuration command. The policy map can be used to take on page 29. A policy map can include setting a specific DSCP value in class maps with these restrictions:
- Actions can...
User Guide - Page 35
On a trunk interface configured for QoS, traffic in the physical port egress queue depending on Ethernet switch network modules. The packets can be placed in all traffic received through the interface is forwarded only to those interfaces associated with a specific VLAN ID egressing from the CPU to trust either CoS or DSCP, but not both at...
User Guide - Page 36
... request. If you can configure the switch to a multicast router port with IGMP version 2 hosts. The VLAN interface is supported only with the ip igmp snooping mrouter global configuration command
You can statically configure MAC multicast groups by IGMP snooping. Immediate Leave is pruned from the table entry. Ethernet switch network modules support a maximum of these methods...
User Guide - Page 37
... Host 1, the CPU uses the information to distinguish IGMP information packets from becoming overloaded with the equivalent MAC destination address of Packet !IGMP
Ports 1, 2
Note that includes the port numbers of Host 4 to the CPU. Figure 16 Initial IGMP Join Message
Cisco router with Ethernet switch network module
1 IGMP Report 224.1.2.3
CPU port
Multicast Forwarding
Table
88849...
User Guide - Page 40
... integrated inline power and QoS features that can use port security to filter traffic destined to access the port is a section describing the default settings on your network. and 36-Port Ethernet Switch Module for Voice, Video and Integrated Data) based voice-over-IP (VoIP) networks to shut down or to support Cisco IP phones in small branch offices, applications...
User Guide - Page 41
... 9 describes guidelines for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Feature Overview
Default Switch Configuration By default, the Ethernet switch network module provides the following settings with the set to receive on the switch. • Inline power is called a pause frame.
You can use send desired when a remote port is set port flowcontrol command. Indicates...
User Guide - Page 74
... timer because the Ethernet switch network module could go out of synchronization.
Verifying the Aging Timer
Step 1
Use the show mac-address-table aging-time command to verify the MAC Address Table:
Router# show mac-address-table aging-time Mac address aging time 23
Configuring Cisco Discovery Protocol
• Enabling Cisco Discovery Protocol, page 75 •...
User Guide - Page 81
... end of service (TOS) minimize monetary cost bit. and 36-Port Ethernet Switch Module for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series
Configuration Tasks
Supported parameters can be grouped into these categories: • TCP • UDP Table 12 lists the possible filtering parameters for ACEs for Cisco IOS Release 12.2. Note The Ethernet switch network module does not...
User Guide - Page 108
... the same subnet. Setting the bits to deploy IP telephony.) When this marking changed to a Differentiated Services Code Point ([DSCP]) value of EF.) However, to ensure that there is one of which requires a unique IP address.
• Administering a network with the necessary VLAN information.
Enters the interface configuration mode and the port to send voice and...
User Guide - Page 112
... enabled by a com domain name, so its location or domain.
QoS uses classification and scheduling to IP addresses. Domain names are included: • Configuring a Port to Connect to a Cisco 7960 IP phone, page 113 • Disabling Inline Power on the Ethernet switch network module. The Cisco 7960 IP phone contains an integrated three-port 10/100 switch. A specific device in...
Cisco NM-1HSSI Reviews
We have not received any reviews for Cisco yet.